Samsung ML-4600/XET Bedienungsanleitung

SERVICE

LASER PRINTER

ML-4600/XET

SAMSUNG

Manual

LASER PRINTER CONTENTS

1. Precautions

2. Specifications

3. Disassembly and Reassembly

4. Troubleshooting

5. Exploded Views and Parts List

6. Electrical Parts List

7. Block Diagrams

8. Connection Diagrams

9. PCB Diagrams

10.Schematic Diagrams

ELECTRONICS

Printed in Korea.

VERSION NO. : 1.00 P/N.: JC-0029A

1. Precautions

Follow these safety, ESD, and servicing precautions to prevent personal injury and equipment damage.

1-1 Safety Precautions

1. Be sure that all built-in protective devices are in

place. Restore any missing protective shields.

2. Make sure there are no cabinet openings through

which people- particularly children- might insert

fingers or objects and contact dangerous voltages.

3. When re-installing chassis and assemblies, be

sure to restore all protective devices, including

control knobs and compartment covers.

4. Design Alteration Warning:

Never alter or add to the mechanical or electrical

design of this equipment, such as auxiliary

connectors, etc. Such alterations and

modifications will void the manufacturer’s

warranty.

5. Components, parts, and wiring that appear to

have overheated or are otherwise damaged

should be replaced with parts which meet the

original specifications. Always determine the

cause of damage or overheating, and correct any

potential hazards.

6. Observe the original lead dress, especially near

sharp edges, AC, and high voltage power

supplies. Always inspect for pinched, out-of-

place, or frayed wiring. Do not change the

spacing between components and the printed

circuit board.

7. Product Safety Notice:

Some electrical and mechanical parts have special

safety-related characteristics which might not be

obvious from visual inspection. These safety

features and the protection they provide could be

lost if a replacement component differs from the

original. This holds true, even though the

replacement may be rated for higher voltage,

wattage, etc.

Components critical for safety are indicated in

the parts list with symbols . Use only

replacement components that have the same

ratings, especially for flame resistance and

dielectric specifications. A replacement part that

does not have the same safety characteristics as

the original may create shock, fire, or other safety

hazards.

Samsung Electronics 1-1

1-2 Samsung Electronics

Precautions

1-2 ESD Precautions

Certain semiconductor devices can be easily

damaged by static electricity. Such components are

commonly called “Electrostatically Sensitive (ES)

Devices”, or ESDs. Examples of typical ESDs are:

integrated circuits, some field effect transistors, and

semiconductor “chip” components.

The techniques outlined below should be followed

to help reduce the incidence of component damage

caused by static electricity.

CAUTION: Be sure no power is applied to the

chassis or circuit, and observe all other safety

precautions.

1. Immediately before handling a semiconductor

component or semiconductor-equipped assembly,

drain off any electrostatic charge on your body

by touching a known earth ground. Alternatively,

employ a commercially available wrist strap

device, which should be removed for your personal

safety reasons prior to applying power to the unit

under test.

2. After removing an electrical assembly equipped

with ESDs, place the assembly on a conductive

surface, such as aluminum or copper foil, or

conductive foam, to prevent electrostatic charge

buildup in the vicinity of the assembly.

3. Use only a grounded tip soldering iron to solder

or desolder ESDs.

4. Use only an “anti-static” solder removal device.

Some solder removal devices not classified as

“anti-static” can generate electrical charges

sufficient to damage ESDs.

5. Do not use Freon-propelled chemicals. When

sprayed, these can generate electrical charges

sufficient to damage ESDs.

6. Do not remove a replacement ESD from its

protective packaging until immediately before

installing it. Most replacement ESDs are

packaged with all leads shorted together by

conductive foam, aluminum foil, or a comparable

conductive material.

7. Immediately before removing the protective

shorting material from the leads of a replacement

ESD, touch the protective material to the chassis

or circuit assembly into which the device will be

installed.

8. Maintain continuous electrical contact between

the ESD and the assembly into which it will be

installed, until completely plugged or soldered

into the circuit.

9. Minimize bodily motions when handling

unpackaged replacement ESDs. Normal motions,

such as the brushing together of clothing fabric

and lifting one’s foot from a carpeted floor, can

generate static electricity sufficient to damage an

ESD.

1. Exercise caution when replacing a super

capacitor or Lithium battery. There could be a

danger of explosion and subsequent operator

injury and/or equipment damage if incorrectly

installed.

2. Be sure to replace the battery with the same or

equivalent type recommended by the

manufacturer.

3. Super capacitor or Lithium batteries contain toxic

substances and should not be opened, crushed,

or burned for disposal.

1-3 Super Capacitor or Lithium Battery Precautions

2. Specification

2-1 Printer

Print Speed 8 PPM (Letter Size, 5% Charcter Pattern) At Copy Mode

Resolution 1200dpi class

Source of Light Laser Diode(LSU)

Print Method Non-impact Electrophotography, Laser Beam

Feed Method Manual Feeder and Auto Tray

Feed Reference Center Reference Loading

Paper Size Bin Type

Normal Paper : A4,Letter,Legal,B5,

Executive, A5

Envelope : Normal Envelope

Length : 149 ~ 365mm

Width : 100 ~ 216mm

Weight : For MPF, 60 ~ 90g/m2

For Manual, 60 ~163g/m2

Paper Capacity MPF : 150 Sheets (based on 75g/m2)

Manual Slot : 1 Sheet

Paper Stacker Capacity Face up : 100 Sheets (75g/m2,20 lb)

Warming up Time Under 30 Sec

First Printing Time Stand-By : Under 20Sec

Power Save Mode :Less than 5min

Power Rating AC 110V ~120V ± 15% 50/60Hz ± 3Hz,

AC 220V ~ 240V ± 15% 50/60Hz ± 3Hz

Power Consumption Avg. 180Wh

Power Saving Consumption Avg. 10Wh Sleep Mode

Certification & Compliance FCC, C-UL, CE, CB,TUV

Acoustic Noise Stand-by : Less than 35dB

Sleep Mode : Less than 29dB

Operating : Less than 50dB

Samsung Electronics 2-1

2-2 Samsung Electronics

Toner Cartridge One-Cartridge type

Expected Life Span 50,000 Sheets

Operating Environment Temperature : 10 ~ 32°C

Humidity : 20 ~ 85%

Storage Environment Temperature : -20 ~ 40°C

Humidity : 10 ~ 95%RH

Weight Net : Max.6.5kg(with Accessory)

Gross : Max. 9kg

External Dimension 329(W) X 343(D) x 224(H)mm

Developer . Life Span : 5% Pattern,Min. 2,500/1,000 Sheets

. Developing : Non-magnetic

Contact Developing

. Charging : Conductive Roller Charging

. Density Adjustment : Normal/Economic Mode selectable by the

PC driver (Only ML-4500)

. Toner Supply Method : Exchanging

Toner Cartridge

. New Developer Checkable

. Transfer System : Conductive Roller Transfer

. Fusing System : Temperature & Pressure

. OZONE Emission : Max. 0.1 PPM(8 Hours)

Specification

Samsung Electronics 2-3

Specification

2-2 Quality

Conditions

Paper Normal Paper 75g/m2

Environment Temperature : 20 ~ 25°C

Humidity : 40 ~ 60%

Print Quality

Image Density Min. 1.3

Min. 1.0(Temperature : 10 ~ 15°C)

Background Max. 0.2

Uniformity Max. 0.2(Including Continuous Print)

Fusing Min. 80% (All Black) 75g/m2

Start Position Top : x ± 4.23mm, Side : y ± 4mm From Left

Skew Top : Max. ± 1.5mm/117.9mm

Side : Max. ±1.8mm/241.3mm

Orthogonality ± 1.0mm

Horizontal Scan ± 0.6mm/208mm

(Bowed Line Skew : Pattern 1)

Special Paper Exception Image Density : Min 1.0 (Envelope)

Fusing : Min. 70% (All Black)

(Envelope/OHP/Postcard)

Paper Jam Less than 1/1,000(75g/m2Paper)

Paper Curl First : Less than 10mm (10 Sheets, 75g/m2Paper)

After Cooling : Less than 10mm (10 Sheets, 75g/m2Paper)

Reliability

Insulation Resistance Less than 10 MΩ(at DC 500V)

Dielectric Strength AC 1000V (DC 1420V), 10mA

Ground Continuity Less than 0.1Ω

Voltage DIP Rated Voltage ± 15%

AC Impulse Noise AC 1000V 10, 100, 200, 400, 1000ns Rated Power

Leakage Current Less than 3.5mA

Surge 6 KV, 500A/3 KV, 500A

OZONE Emission Less than 0.1 ppm (8 Hours)

Top Cover Open Isolating the input power of the LSU,

High Voltage Part, and Fuser

Overcurrent Protect Fuse inside the SMPS

Fusing System

Trouble Sensing .The temperature doesn’t rise to the specific

temperature in the specific time.

.The temperature is too high.

Overheat Sensing 240 ~ 250°C (The thermostat cuts off the Fuser

from the power.)

Thermistor Open Sensing .Without the initial temperature change of the Fuser

Indicate the

Fuser error

2-4 Samsung Electronics

Specification

2-3 SMPS (Switching Mode Power Supply)

Input (AC)

AC Input Voltage Europe USA

Minimum 198V 90V

Typical 230V 120V

Maximum 264V 135V

Max. AC Input Current 2.5Amps 3Amps

Max. Inrush Current Ap-p (at 20°C)

Output (DC)

Line Regulation 24V ± 10%

5V ± 5%

Road Regulation 24V ± 10%

5V ± 5%,-5V ± 5%

Ripple Noise 24V : Peak 300mV

-5V : Peak 500mV

5V : Peak 500mV

Over Current Protect 24V : 2.7A ± 10% (by Circuit)

5V : A ± 10% (by Circuit)

Over Voltage Protect 24V : 33VDC

5V : 5.6VDC

3-1Samsung Electronics

3. Disassembly and Reassembly

3-1 General Precautions on Disassembly

When you disassemble and reassemble components, you must use extreme caution. The close proximity of

cables to moving parts makes proper routing a must. If components are removed, any cables disturbed by the

procedure must be restored as close as possible to their original positions. Before removing any component

from the machine, note the cable routing that will be affected.

Whenever servicing the machine, you must perform as follows:

1. Remove the print cartridge. Do not expose the cartridge to direct room light or sun light, and be careful not

to scratch the drum surface.

2. Turn the power switch off.

3. Unplug all the cables from the printer.

4. Replace with only an authorized component.

5. Do not force to open or fasten a plastic material component.

6. Be careful no obstacles are included when you reassemble components.

7. When you reassemble components, be careful small size components are located in place.

8. If you turn the machine over to replace some parts, toner or paper particles may contaminate the LSU win-

dow. Protect the LSU window with clean paper.

Releasing Plastic Latches

Many of the parts are held in place with plastic

latches. The latches break easily; release them care-

fully. To remove such parts, press the hook end of

the latch away from the part to which it is latched.

Disassembly and Reassembly

3-2 Samsung Electronics

3-2 OPE Cover

1. Hold both sides of the cover and pull it towards

you. 3. Release the right-bottom of the cover, then pull it

in the direction of arrow to release the other end.

2. Remove the one screw to release the stopper

securing the cover to the main body. 4. Unplug the connector connecting the OPE cover

to the main body and remove the cover.

Inhaltsverzeichnis

Andere Samsung Drucker Handbücher

Samsung

Samsung ML-551x Bedienungsanleitung

Samsung

Samsung ML-1630W/SEE Bedienungsanleitung

Samsung

Samsung Xpress CLP-41 series Bedienungsanleitung

Samsung

Samsung ML-2950ND Bedienungsanleitung

Samsung

Samsung SL-M3820DW/XAA Bedienungsanleitung

Samsung

Samsung Xpress C1810W Bedienungsanleitung

Samsung

Samsung ML-6050 Bedienungsanleitung

Samsung

Samsung CLP-680ND: CLP-775ND Benutzerhandbuch

Samsung

Samsung CLP-36x Series Bedienungsanleitung

Samsung

Samsung ML-2525 Bedienungsanleitung

Samsung

Samsung ML-2240 Series Bedienungsanleitung

Samsung

Samsung ML-1450 Series Benutzerhandbuch

Samsung

Samsung SL-C460FW Benutzerhandbuch

Samsung

Samsung ML-7300N Bedienungsanleitung

Samsung

Samsung CLP-775ND Bedienungsanleitung

Samsung

Samsung SCX-4833FD Bedienungsanleitung

Samsung

Samsung SCX-1100 Bedienungsanleitung

Samsung

Samsung ML 2250 Montage- und Wartungsanleitung

Samsung

Samsung Multifunction MultiXpress X322 Series Bedienungsanleitung

Samsung

Samsung ML 3050 - B/W Laser Printer Bedienungsanleitung

Samsung

Samsung SCX-5315F Bedienungsanleitung

Samsung

Samsung Xpress C1810 series Bedienungsanleitung

Samsung

Samsung CLP CLP-300N Bedienungsanleitung

Samsung

Samsung Multifunction ProXpress C267 Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung

Lexmark

Lexmark Infoprint 1332 Bedienungsanleitung