Samsung SRP-350 Bixolon Bedienungsanleitung

Operator’s Manual

All specifications are subjected to change without notice

SRP - 350

RECEIPT PRINTER

1-7. Adjustments and Settings

The SRP-350 is set up at the factory to be appropriate for almost all users. It does,

however, offer some settings for users with special requirements.

It has DIP switches that allow you to change communication settings, such as

handshaking and parity check, as well as print density.

The SRP-350 also has a near-end sensor for the paper. This can give you a warning

when the paper is almost out. If you find that there is not enough paper remaining on

the roll when the near-end detector is triggered, you can change the near-end sensor

setting.

1-8. Using the Printer

Control Panel

Button

The button can be disabled by the ESC c 5 command.

Press the FEED button once to advance paper one line. You can also hold down the

FEED

button to feed paper continuously.

Panel lights

POWER

The POWER light is on whenever the printer is on.

ERROR

This indicates an error.

PAPER OUT

This light indicates the near end of the paper roll. Install a new paper roll and the

printer

will continue printing.

When the light blinks, it indicates the self-test printing standby state or macro

execution

standby state when the macro execution command is used.

Serial Interface Specification

DIP Switch Set 1 Functions

SW FUNCTION ON OFF DEFAULT

1 Data Receive Error Ignore Print ‘‘ ?’’ OFF

2 Mode Selection STAR EPSON OFF

3 HandShaking XON/OFF DTR/DSR OFF

4 Word length 7 bits 8 bits OFF

5 Parity check Yes No OFF

6 Parity selection EVEN ODD OFF

7 ON

8 Baud rate selection Refer to the Following Table OFF

Baud rate selection

Transmission speed SW – 7 SW – 8

2400 baud ON ON

4800 baud OFF ON

9600 baud ON OFF

19200 baud OFF OFF

Dip Switch Set 2 Functions

SW FUNCTION ON OFF DEFAULT

1 Reserved - - -

2 Reserved - - -

3 Reserved - -

4 Reserved - -

5 OFF

6 Select Print Density Refer to the Following Table OFF

7 Reserved - - -

8 Reserved - - -

Print Density

Print Density SW - 5 SW – 6

1 ( Light ) ON ON

2 OFF OFF

3 ON OFF

4 ( Dark ) OFF ON

Parallel Interface Specification

Dip Switch Set 1 Functions

SW FUNCTION ON OFF DEFAULT

1 Reserved - - OFF

2 Reserved - - OFF

3 Reserved - - OFF

4 Reserved - - OFF

5 Reserved - - OFF

6 Reserved - - OFF

7 Reserved -- OFF

8 Reserved - - OFF

Dip Switch Set 2 Functions

SW FUNCTION ON OFF DEFAULT

1 Reserved - - -

2 Reserved - - -

3 Reserved - -

4 Reserved - -

5 OFF

6 Select Print Density Refer to the Following Table OFF

7 Reserved - - -

8 Reserved - - -

Print Density

Print Density SW - 5 SW – 6

1 ( Light ) ON ON

2 OFF OFF

3 ON OFF

4 ( Dark ) OFF ON

Chapter 2. Hexadecimal Dumping

This feature allows experienced users to see exactly what data is coming to the printer.

This can be useful in finding software problems. When you turn on the hexadecimal dump

function, the printer prints all commands and data in hexadecimal format along with a

guide section to help you find specific commands.

To use the hexadecimal dump function, follow these steps:

1. After you make sure that the printer is off, open the cover.

2. Turn on the printer, while holding down the FEED button.

3. Close the cover, then the printer enters the hexadecimal dump mode.

4. Run any software program that sends data to the printer. The printer will print all the

codes it receives in a two-column format. The first column contains the hexadecimal

codes and the second column gives the ASCII characters that corresponds to the

codes.

1B 21 00 1B 26 02 40 40 40 40 . ! . . & . @ @ @ @

02 0D 1B 44 0A 14 1E 28 28 28 . . . D . . . . ( ( (

00 01 0A 41 0D 42 0A 43 43 43 . . . A . B . C C C

 A period (.) is printed for each code that has no ASCII equivalent.

 During the hex dump, all commands except DLE EOT and DLE ENQ are

disabled.

5. When the printing finishes, turn off the printer.

6. Turn on the printer and then the hexadecimal mode is off.

Chapter 3. The self test

The self-test checks whether the printer has any problems. If the printer does not function

properly, contact your dealer. The self-test checks the following;

1. Make sure paper roll has been installed properly.

2. Turn on the power while holding down the FEED button. The self-test begins.

3. The self-test prints the current printer status, which provides the control ROM

version

and the DIP switch setting.

4. After printing the current printer status, self-test printing will print the following, and

pause(ThePAPERLEDlightblinks).

Self-testprinting.

PleasepresstheFEEDbutton

5. Press the FEED button to continue printing. The printer prints a pattern using the

built-in character set.

6. The self-test automatically ends and cuts the paper after printing the following.

*** completed ***

The printer is ready to receive data as soon as it completes the self-test.

Control Commands

[Name] Horizontaltab.

[Format] ASCII HT

Hex 09

Decimal 9

[Description] Moves the print position to the next horizontal tab position.

[Name] Print and line feed.

[Format] ASCII LF

Hex 0A

Decimal 10

[Description] Prints the data in the print buffer and feeds one line based on the current

line spacing.

[Name] Print and return to standard mode in page mode.

[Format] ASCII FF

Hex 0C

Decimal 12

[Description] Prints the data in the print buffer collectively and returns to standard

mode.

[Name] Print and carriage return.

[Format] ASCII CR

Hex 0D

Decimal 13

[Description] When automatic line feed is enabled, this command functions the same as

LF; when automatic line feed is disabled, this command is ignored.

CAN

[Name] Cancel print data in page mode.

[Format] ASCII CAN

Hex 18

Decimal 24

[Description] In page mode, deletes all the print data in the current printable area.

DLE EOT n

[Name] Real-time status transmission.

[Format] ASCII DLE EOT n

Hex 10 04 n

Decimal 16 4 n

[Range] 1 ≤n ≤4

[Description] Transmits the selected printer status specified by n in real time, according

the following parameters:

n = 1 : Transmit printer status.

n = 2 : Transmit off-line status.

n = 3 : Transmit error status.

n = 4 : Transmit paper roll sensor status.

n = 1 : Printer status.

Bit Off/On Hex Decimal Function

0 Off 00 0 Not used. Fixed to Off.

1 On 02 2 Not used. Fixed to On.

Off 00 0 Drawer open/close signal is LOW

(connector pin 3).

On 04 4 Drawer open/close signal is HIGH

(connector pin 3).

Off 00 0 On-line.3 On 08 8 Off-line.

4 On 10 16 Not used. Fixed to On.

5-6 - - - Undefined.

7 Off 00 0 Not used. Fixed to Off.

n=2:Off-linestatus.

Bit Off/On Hex Decimal Function

0 Off 00 0 Not used. Fixed to off.

1 On 02 2 Not used. Fixed to On.

Off 00 0 Cover is closed.2 On 04 4 Cover is open.

Off 00 0 Paper is not being fed by using the PAPER

FEED button.

3 On 08 8 Paper is being fed by the PAPER FEED

button.

4 On 10 16 Not used. Fixed to On.

Off 00 0 No paper-end stop.5 On 20 32 Printing stops due to paper end.

Off 00 0 No error.6 On 40 64 Error occurs.

7 Off 00 00 Not used. Fixed to Off.

Bit 5 : Becomes on when the paper end sensor detects paper end and printing stops.

n = 3 : Error status

Bit Off/On Hex Decimal Function

0 Off 00 0 Not used. Fixed to Off.

1 On 02 2 Not used. Fixed to On.

2 - - - Undefined.

Off 00 0 No auto-cutter error.3 On 08 8 Auto-cutter error occurs.

4 On 10 16 Not used. Fixed to On.

Off 00 0 No unrecoverable error.5 On 20 32 Unrecoverable error occurs.

Off 00 0 No auto-recoverable error.6 On 40 64 Auto recoverable error occurs.

7 Off 00 0 Not used. Fixed to Off.

Bit 3: If these errors occur due to paper jams or the like, it is possible to

recover by

correcting the cause of the error and executing DLE ENQ n(1 ≤n ≤2).

Ifanerrorduetoacircuitfailure (e.g. wire break) occurs, it is impossible

recover.

Bit 6: When printing is stopped due to high print head temperature until the print

head temperature drops sufficiently or when the paper roll cover is open

during printing, bit 6 is On.

n = 4 : Continuous paper sensor status.

Bit Off/On Hex Decimal Function

0 Off 00 0 Not used. Fixed to off.

1 On 02 2 Not used. Fixed to On.

2 Off 00 0 Paper roll near-end sensor. Paper adequate.

3 On 0C 12 Paper near-end is detected by the paper roll

near-end sensor.

4 On 10 16 Not used. Fixed to On.

5 Off 00 0 Not roll end sensor. Paper present.

6 On 60 96 Paper is detected by the paper roll end

sensor.

7 Off 00 0 Not used. Fixed to Off.

DLE ENQ n

[Name] Real-time request to printer.

[Format] ASCII DLE ENQ n

Hex 10 05 n

Decimal 16 5 n

[Range] 1 ≤n ≤2

[Description] Recover from an error and restart printing from the line where the error

occurred

ESC FF

[Name] Print data in page mode

[Format] ASCII ESC FF

Hex 1B 0C

Decimal 27 12

[Description] In page mode, prints all buffered data in the printing area collectively.

ESC SP n

[Name] Set right-side character spacing.

[Format] ASCII ESC SP n

Hex 1B 20 n

Decimal 27 32 n

[Range] 0 ≤n ≤255

[Description] Sets the character spacing for the right side of the character to [n x

horizontal or vertical motion units].

ESC ! n

[Name] Select print modes.

[Format] ASCII ESC ! n

Hex 1B 21 n

Decimal 27 33 n

[Range] 0 ≤n ≤255

[Description] Selects print mode(s) using n as follows:

Bit Off/On Hex Decimal Function

Off 00 0 Character font A (12 × 24)0 On 01 1 Character font B (9 × 17)

1 - - - Undefined.

2 - - - Undefined.

Off 00 0 Emphasized mode not selected.3 On 08 8 Emphasized mode selected.

Off 00 0 Double-height mode not selected.4 On 10 16 Double-height mode selected.

Off 00 0 Double-width mode not selected.5 On 20 32 Double-width mode selected.

6 - - - Undefined.

Off 00 0 Underline mode not selected.7 On 80 128 Underline mode selected.

Andere Handbücher für SRP-350 Bixolon

Inhaltsverzeichnis

Andere Samsung Drucker Handbücher

Samsung

Samsung ML-3561N Series Bedienungsanleitung

Samsung

Samsung ML-1440 Bedienungsanleitung

Samsung

Samsung SRP-350 Bixolon Bedienungsanleitung

Samsung

Samsung CLP-770ND - Color Laser Printer Bedienungsanleitung

Samsung

Samsung ML-3750ND Bedienungsanleitung

Samsung

Samsung Xpress C181xW Series Bedienungsanleitung

Samsung

Samsung ML 4050N - B/W Laser Printer Bedienungsanleitung

Samsung

Samsung ML-2251NP - Network Business Laser Printer Benutzerhandbuch

Samsung

Samsung C41x Series Bedienungsanleitung

Samsung

Samsung CPL-36 Series Bedienungsanleitung

Samsung

Samsung CLP-650 Series Bedienungsanleitung

Samsung

Samsung ML-1450 Series Bedienungsanleitung

Samsung

Samsung CLP-775ND Bedienungsanleitung

Samsung

Samsung CLX-9250ND Gebrauchs- und Pflegehandbuch

Samsung

Samsung ML-5050G Series Bedienungsanleitung

Samsung

Samsung SCX-5635FN - Mono Laser P/s/c/f USB Enet 1200X1200 128MB... Bedienungsanleitung

Samsung

Samsung ML-4500/XAA Bedienungsanleitung

Samsung

Samsung CLP-315 Series Bedienungsanleitung

Samsung

Samsung ML--6100 Kurzanleitung

Samsung

Samsung SL-C460FW Bedienungsanleitung

Samsung

Samsung CLP-775ND Benutzerhandbuch

Samsung

Samsung CLX-9201NA Bedienungsanleitung

Samsung

Samsung ML-6040 Bedienungsanleitung

Samsung

Samsung ML-2851ND/SEE Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung

IRA3D

IRA3D POETRY4 Bedienungsanleitung