Samsung SCC-B9372 Bedienungsanleitung

SCC-B9372

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at

www.samsung.com/global/register

operating instructions

DAY&NIGHT IR LED CAMERA

ENG FRA GER SPA ITA

01-SCC_B9372_EU-ENG.indd 1 2008-03-10 오후 3:57:55

safety precautions

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)NO USER-SERVICEABLE PARTS

INSIDEREFER SERVICING TO QUALIFIED SERVICE PERSONNEL

This symbol indicates that dangerous voltage consisting a risk of electric shock is present

within this unit.

This symbol indicates that there are important operating and maintenance instructions in

the literature accompanying this unit.

WARNING

To reduce the risk of ﬁre or electric shock, do not expose this appliance to rain or moisture.

WARNING

1. Be sure to use only the standard adapter that is speciﬁed in the speciﬁcation sheet.

Using any other adapter could cause ﬁre, electrical shock, or damage to the product.

2. Incorrectly connecting the power supply or replacing battery may cause explosion,

ﬁre, electric shock, or damage to the product.

3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may

cause abnormal heat generation or ﬁre.

4. Securely plug the power cord into the power receptacle. Insecure connection may

cause ﬁre.

5. When installing the camera, fasten it securely and ﬁrmly. A falling camera may cause

personal injury.

6. Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or

containers ﬁlled with water on top of the camera.

Doing so may cause personal injury due to ﬁre, electric shock, or falling objects.

7. Do not install the unit in humid, dusty, or sooty locations.

Doing so may cause ﬁre or electric shock.

8. If any unusual smells or smoke come from the unit, stop using the product.

In such case, immediately disconnect the power source and contact the service

centre. Continued use in such a condition may cause ﬁre or electric shock.

9. If this product fails to operate normally, contact the nearest service centre.

Never disassemble or modify this product in any way. (SAMSUNG is not liable for

problems caused by unauthorized modiﬁcations or attempted repair.)

10. When cleaning, do not spray water directly onto parts of the product.

Doing so may cause ﬁre or electric shock.

•

01-SCC_B9372_EU-ENG.indd 2 2008-03-10 오후 3:57:55

CAUTION

1. Do not drop objects on the product or apply strong shock to it.

Keep away from a location subject to excessive vibration or magnetic interference.

2. Do not install in a location subject to high temperature (over 122°F), low temperature

(below 14°F), or high humidity. Doing so may cause ﬁre or electric shock.

3. If you want to relocate the already installed product, be sure to turn off the power

and then move or reinstall it.

4. Remove the power plug from the outlet when then there is a lightning.

Neglecting to do so may cause ﬁre or damage to the product.

5. Keep out of direct sunlight and heat radiation sources. It may cause ﬁre.

6. Install it in a place with good ventilation.

7. Avoid aiming the camera directly towards extremely bright objects such as sun,

as this may damage the CCD image sensor.

8. Apparatus shall not be exposed to dripping or splashing and no objects ﬁlled with

liquids, such as vases, shall be placed on the apparatus.

9. The Mains plug is used as a disconnect device and shall stay readily operable at

any time.

01-SCC_B9372_EU-ENG.indd 3 2008-03-10 오후 3:57:55

important safety instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers,

or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong is provided for your safety.

If the provided plug does not ﬁt into your outlet, consult an electrician for replacement

of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with cart, stand, tripod, bracket, or table speciﬁed by the manufacturer,

or sold with the apparatus.

13. Unplug this apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

14. Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been exposed to rain or moisture,

does not operate normally, or been dropped.

01-SCC_B9372_EU-ENG.indd 4 2008-03-10 오후 3:57:55

_01

contents

FEATURES

02 Features

FUNCTION &

INSTALLATION

03 Function

04 Installation method

TROUBLESHOOTING

05 Troubleshooting

SPECIFICATIONS

06 Speciﬁcations

DIMENSIONS

07 Dimensions

contents

THINGS TO KEEP IN MIND

DURING INSTALLATION

AND USE

02 Things to keep in mind during installation and

use

01-SCC_B9372_EU-ENG.indd 1 2008-03-10 오후 3:57:55

02_

features

SONY 1/3” Super HAD High-resolution Colour CCD

Resolution: 540TVL (Colour), 570TVL (B/W)

Externally Adjustable Focal Length & Focus by Rings

Filter Changeable Vari-Focal DC Auto Iris 3.8~9.5mm F1.2 Lens Built -in.

Colour & B/W Auto Switchable by Photocell and Sensitivity

CDS Auto Switching IR LED Control (42 IR LEDs)

Externally Adjustable DC Iris Level

Dip Switch control of Day & Night time delay, Flickerless

BLC and White Balance

AC24V/DC12V Dual Power Available

Waterproof Outdoor Installation (IP-66)

things to keep in mind during

installation and use

Do not disassemble the camera on your own.

Always be careful when handling the camera. Do not strike the camera by your

ﬁsts or shake it. Please be careful not to be careless when storing and operat-

ing it.

Do not place or operate the camera in any wet environment such as rain or

wet surfaces.

Do not clean the camera with rough sandpaper. Please always use a dry cloth

when cleaning it.

Put the camera in a cool area free from direct sunlight. Otherwise, the camera

may be damaged.

•

features

01-SCC_B9372_EU-ENG.indd 2 2008-03-10 오후 3:57:55

_03

ENG

function & installation

FUNCTION

1Protective Film over Front Glass : Remove this ﬁlm before operating the Camera.

2Focus/Zoom Lever Bolt Screws: Used to ﬁx the Focus/Zoom ring to the lens internally.

Be careful not to lose this small bolt screws which need not be touched other than by a

service technician.

3Focus/Zoom Ring Fixing Screws: Used to ﬁx the Focus/Zoom Ring at the desired

position after adjusting the lens angle and focus setting as described below.

4Focus and Zoom Ring: These two rings are used to accurately adjust the viewing angle

and to sharply focus all objects within the lens ﬁeld of view.

- Loosen the ﬁxing screws ( 3) to turn the Zoom and Focus ring.

i) To widen the viewing angle turn the “Zoom Ring” to “W” (Wide).

ii) To obtain a closer view turn this ring to “T” (Tele).

- After adjustment of the viewing angle then adjust the “Focus Ring” between “N” (Near) or “ ”

(Far) until the sharpest focus is achieved.

- Then tighten the ﬁxing screws ( 3) on each ring.

- After tightening you should check that angle and focus is still accurate.

5DC Level Volume Screw Cap :

- Loosen the DC level volume screw cap on the camera body.

i) For a brighter screen turn the DC level volume slowly toward “H” (counter-clockwise),

ii) For a darker screen turn it toward “L” (clockwise) with a driver.

6Bracket : Used to install the camera to the desired location.

function & installation

[THE OTHER SIDE VIEW]

VIDEO

POWER

01-SCC_B9372_EU-ENG.indd 3 2008-03-10 오후 3:57:56

04_

function & installation

INSTALLATION METHOD

Bracket & Camera Mounting

- Install the Mounting Bracket at the desired location.

Connecting to Monitor and Power

- Set the impedance switch to the 75 standard position unless a video equipment is connected

to the monitor video out.

- Adaptor: AC24V / 800mA or DC12V / 1A (AC24V / DC12V Model)

• Be sure to connect power after all the installation is done.

• Do not use power sources other than that speciﬁed.

- After adjusting view angle, cap over the camera with the sun-shield and ﬁx it to the camera with

the sun-shield bolt.

01-SCC_B9372_EU-ENG.indd 4 2008-03-10 오후 3:57:56

_05

ENG

troubleshooting

If you have trouble operating the camera, check the following guides for the

possible problem.

Nothing appears on the screen.

- Check the power connection and video signal line connection.

- Check the brightness level of DC Auto Iris volume of the camera.

The video image is not clear.

- Check if the camera glass has dust on the surface.

Clean the camera glass with a clean cloth or brush.

- Make sure that the screen is not exposed directly to a bright light.

Adjust the position of the camera if necessary.

- Check if protective ﬁlm of camera glass is removed.

The screen is dark

- Adjust the brightness feature of the monitor.

- Check the brightness level of DC Auto Iris volume of the camera.

The screen does not properly display when IR LEDs work.

- Check if the camera glass has dust.

- Clean the camera glass with a clean cloth or brush.

If you cannot solve the problem with above guidelines, please contact an

authorized technician.

•

01-SCC_B9372_EU-ENG.indd 5 2008-03-10 오후 3:57:56

06_

specifications

ITEM PAL

Image Sensor 1/3" Interline transfer type colour CCD (SONY)

Effective Pixels 752H × 582V (440K pixels)

Scanning System 625 Lines 2:1 Interlace

Scanning Frequency 15.625KHz (H), 50Hz (V)

Resolution 540TVL (Colour), 570TVL (B/W)

Shutter Speed 1/50 sec.

S/N Ratio More than 48dB (AGC Off)

Sync. System Internal

Min. Illumination 0 Lux (IR LED On)

White Balance ATW / AWC selectable

Video Output VBS 1.0 Vp-p (75 Load)

Lens 3.8~9.5mm Vari -Focal, DC Auto Iris F1.2 Day & Night Lens

Power Supply(*) AC24V±10%, DC12V±10%

Power Consumption 2.5W(LED Off)/7.8W(LED On)

Operating Temp. -10˚C~50˚C (14˚F~122˚F)

Operational Humidity Max. 90% RH

Dimensions 77.5mm (Ø) × 129mm (L)

(*) Must use regulated & specified power supply.

speciﬁcations

01-SCC_B9372_EU-ENG.indd 6 2008-03-10 오후 3:57:56

Inhaltsverzeichnis

Andere Samsung Sicherheitskamera Handbücher

Samsung

Samsung SCC-C6435(P) Bedienungsanleitung

Samsung

Samsung HCO-E6070R Bedienungsanleitung

Samsung

Samsung SDC-415 Series Bedienungsanleitung

Samsung

Samsung SNB-6005 Bedienungsanleitung

Samsung

Samsung SCC-B2003P Bedienungsanleitung

Samsung

Samsung SNV-3120 Bedienungsanleitung

Samsung

Samsung SDC-435 Bedienungsanleitung

Samsung

Samsung SCC-B9371 Bedienungsanleitung

Samsung

Samsung SCZ-3250PD Bedienungsanleitung

Samsung

Samsung iPolis SNV-6084 Bedienungsanleitung

Samsung

Samsung SNC-B5399 Bedienungsanleitung

Samsung

Samsung SID-600P Bedienungsanleitung

Samsung

Samsung SCC-641 - 22x Zoom Smart Dome Camera Bedienungsanleitung

Samsung

Samsung SCV-5085 Bedienungsanleitung

Samsung

Samsung SCC-B9374 Bedienungsanleitung

Samsung

Samsung SCD-3083 Installationsanleitung

Samsung

Samsung AB68-00504B Bedienungsanleitung

Samsung

Samsung SND-560 Bedienungsanleitung

Samsung

Samsung SCD-1020P Bedienungsanleitung

Samsung

Samsung SNF-7010 Bedienungsanleitung

Samsung

Samsung SCC-C6453P Bedienungsanleitung

Samsung

Samsung SHC-730N/P Bedienungsanleitung

Samsung

Samsung SDZ-375 Bedienungsanleitung

Samsung

Samsung SND-5080 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung