Samsung SND-7080F Bedienungsanleitung

NETWORK CAMERA

Quick Guide SND-7080F

English

PT01-000156A-SND-7080FN-QG_ENGLI1 1 2011-03-24 오후 6:51:48

2_ English2

WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package.

Appearance Item Name Quantity Description

User Manual,

Installer S/W DVD,

CMS S/W DVD

Quick Guide 1

Iron Screw 3 Used for fixing to an iron plate

Cable for the testing

monitor 1Used to test the camera connection to a

portable display device

Template 1 Product installation guide

Tapping Screw 1 Used to fix the safety bracket

Bracket Safety 1 Safety Bracket

PT01-000156A-SND-7080FN-QG_ENGLI2 2 2011-03-24 오후 6:51:48

English

English _3

AT A GLANCE

Appearance

Item Description

Top cover Case cover used to protect the lens and the main unit.

Camera Case Covers the lens and camera body.

Power Port Used to plug the power cable.

Alarm In /

Out terminals

ARM-IN BLUE : Used to connect the alarm input signal.

ARM-OUT WHITE : Used to connect the alarm output signal.

A-COM GRAY : Common port where the alarm output signal is

connected.

GND YELLOW : Used for earth-grounding.

Network Port Used to connect a PoE or LAN cable.

Video Out Port Analog video output port. (for installation)

Audio In Jack Used to connect to a microphone.

Audio Out Jack Used to connect to speakers.

PT01-000156A-SND-7080FN-QG_ENGLI3 3 2011-03-24 오후 6:51:49

4_ English4

Inside

Item Description

Monitor Out Using the test monitor cable, you can connect to a mobile display for camera

test.

Reset Button

Resets the camera settings to the default. Press and hold it for about 5

seconds to turn off the system indicator and restart the system.

If you reset the camera, the network settings will be adjusted so that

DHCP can be enabled. If there is no DHCP server in the network, you

must run the IP Installer program to change the basic network settings

such as IP address, Subnet mask, Gateway, etc., before you can

connect to the network.

SD Memory Card

Compartment Compartment for the SD memory card.

PT01-000156A-SND-7080FN-QG_ENGLI4 4 2011-03-24 오후 6:51:49

English

English _5

INSTALLATION

Precautions before installation

Ensure you read out the following instructions before installing the camera:

Select an installation site (ceiling or wall) that can endure at least 5 times of the

camera weight.

Stuck-in or peeled-off cables can cause damage to the product or a ﬁre.

For safety purposes, keep anyone else away from the installation site. And put aside

personal belongings from the site, just in case.

Disassembling

Take the camera body with one hand and take the

top cover with the other hand. Then, turn the cover

counter clockwise to remove it.

Installation

Use the provided template to drill one hole for

the camera, and one for the screw (5 mm in

diameter, at least 35 mm in depth), and insert

the plastic anchor (HUR 5) to the end of the

screw hole.

Connect and arrange the necessary cables

lest that they should be damaged or twisted

while installing the camera.

Insert the camera body into the hole so that it

ﬁts to the camera hole, and ﬁx the body using

the ASSY tapping screws (TH M4xL30). (x3)

Refer to “Adjusting the monitoring direction for the camera” to adjust the lens in a

desired direction.

Close the top cover.

Fit the top cover into the ﬁxing tips of the camera body and turn the cover clockwise.





Top cover

Camera Body

PT01-000156A-SND-7080FN-QG_ENGLI5 5 2011-03-24 오후 6:51:49

6_ English6

Adjusting the monitoring direction for the camera

Adjusting the monitoring direction

You can adjust the camera direction only when the camera is fixed on the ceiling.

Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called

Tilt, and turning the lens on its axis is called Rotate.

The effective range of pan is a total of 355 degrees.

The effective range of rotation is a total of 355 degrees.

The effective range of tilt is a total of 90 degrees.

In some angles, the top cover may cause cutting some part of the monitoring object.

Do not rotate the focus/zoom lens by force after removing the cover front.

Otherwise, it may cause an incorrect focus due to a motor failure.

Methods of adjustment

After installing the camera, adjust the panning angle in consideration of the

monitoring direction.

When tilting the camera, you should adjust the horizontal angle lest that the image

be displayed reversely.

Adjust the rotation angle to correct the image display position (up/down/left/right).

Rotating means rotation on the basis of the rear lens unit.

Adjust the tilt angle so that the camera faces toward the monitoring object.

❖

J



❖



Panning

Tilting

Lens rotation

Cover Front

PT01-000156A-SND-7080FN-QG_ENGLI6 6 2011-03-24 오후 6:51:49

English

English _7

CONNECTING WITH OTHER DEVICE

Connecting to the monitor

Connect the video out port of the camera to the video input port of the monitor.

In the initial installation of the camera, you can connect the camera to the monitor for checking

the connection status.

You can set the video output type to either NTSC or PAL.

Ethernet Connection

Connect the Ethernet cable to the local network or to the Internet.

Power Supply

Use the screwdriver to connect each line (+, –) of the power cable to the corresponding

power port of the camera.

Be careful not to reverse the polarity when you connect the power cable.

You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.

If PoE and DC 12V are both applied, this camera will get supplied with power from PoE.

Please make sure the monitor and camera are turned off when connecting them.

M



J



Monitor

Power

Ethernet

Monitor Out

PT01-000156A-SND-7080FN-QG_ENGLI7 7 2011-03-24 오후 6:51:50

8_ English8

Connecting to Audio Input/Output

Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT

port of the ampliﬁer that the microphone is connected to.

Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker.

Check the speciﬁcations for audio input.

Audio Codec

G.711 PCM. μ-law 64kbps 8kHz sampling

Full duplex Audio

Audio in

Used for mono signal line input (Max.2.4 Vpp)

Audio out

Used for mono signal line output (Max.2.4 Vpp)

Line out impedance

600Ω



Network

Speaker

Microphone

Amp

Microphone

Speaker

PT01-000156A-SND-7080FN-QG_ENGLI8 8 2011-03-24 오후 6:51:50

English

English _9

IP SETUP

Manual Network Setup

Run <IP Installer_vX.XX.exe> to display the camera search list.

At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.

For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not

support this function.

Select a camera in the search list.

Find the MAC (Ethernet) address

labeled on the rear of the camera.

Both the [Auto Set] and [Manual Set]

buttons will be activated.

Click [Manual Set].

The Manual Setting dialog appears.

The default values of <IP Address>,

<Subnet Mask>, <Gateway>, <HTTP Port> and <VNP Port> of the camera will

be displayed.

In the <Address> pane, provide the

necessary information.

MAC (Ethernet) Address : The MAC

(Ethernet) address of the applicable

camera will be set automatically so

you don't need to input it manually.

You can conﬁgure the static IP settings

only if the DHCP checkbox is unchecked.

In the <Port> pane, provide necessary information.

HTTP Port : Used to access the camera using the Internet browser, defaulted to

80. Use the spin button to change the HTTP Port value.

VNP Port : Used to control the video signal transfer, defaulted to 4520.

Enter the password.

This is the login password for the “admin” user who accesses the camera.

The default password is “4321”.

Click [OK].

Manual network setup will be completed.

M



M



PT01-000156A-SND-7080FN-QG_ENGLI9 9 2011-03-24 오후 6:51:50

10_ English10

USING THE LIVE SCREEN

Item Description

Monitoring Move to the monitoring screen.

Playback Switch to the monitoring screen that plays recording data in the SD memory.

Setup Move to the Setup screen.

Viewer Screen Displays the Live video on the screen.

Alarm Output Activate the Alarm Out port.

Audio Display the audio Listen and Talk toggle button on the screen.

Hide the alarm

indicator Hides the alarm indicator near the border of the viewer screen.

PT01-000156A-SND-7080FN-QG_ENGLI10 10 2011-03-24 오후 6:51:50

Andere Handbücher für SND-7080F

Inhaltsverzeichnis

Sprachen:

Andere Samsung Sicherheitskamera Handbücher

Samsung

Samsung SCC-C6407 Bedienungsanleitung

Samsung

Samsung BW-2302 SERIES Bedienungsanleitung

Samsung

Samsung SNP-6200 Bedienungsanleitung

Samsung

Samsung SNC-B2335 Bedienungsanleitung

Samsung

Samsung SCC-B5313 Bedienungsanleitung

Samsung

Samsung SCD-3081 Bedienungsanleitung

Samsung

Samsung SCC-B5353 Bedienungsanleitung

Samsung

Samsung SCV-2010F Bedienungsanleitung

Samsung

Samsung SMARTCAM SNH-V6110BN Bedienungsanleitung

Samsung

Samsung SNP-5300 Bedienungsanleitung

Samsung

Samsung SNB-6010A Bedienungsanleitung

Samsung

Samsung SMARTCAM SNH-1011N Bedienungsanleitung

Samsung

Samsung SCC-641 - 22x Zoom Smart Dome Camera Bedienungsanleitung

Samsung

Samsung SCC-B5300(G)(P) Bedienungsanleitung

Samsung

Samsung SNB-1001 Bedienungsanleitung

Samsung

Samsung SCC-C6455N Bedienungsanleitung

Samsung

Samsung SNP-6321 Bedienungsanleitung

Samsung

Samsung SCC-B5393 Bedienungsanleitung

Samsung

Samsung SCD-2020R Series Bedienungsanleitung

Samsung

Samsung SNC-550 iPOLiS Bedienungsanleitung

Samsung

Samsung SIR-60 Bedienungsanleitung

Samsung

Samsung iPolis SNB-5000 Bedienungsanleitung

Samsung

Samsung SID-47 Bedienungsanleitung

Samsung

Samsung SCC-C4253 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung