Samsung SOC-4020 SERIES Bedienungsanleitung

SAMSUNG CCD CAMERA

SOC-4020SERIES

LENS BUILT INCOLOR CCDCAMERA

INSTRUCTION MANUAL

About this manual

Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.

P/No. : 6806-0438-01B

VAN 04. 9

•SAMSUNG TECHWIN CO., LTD.

Optics & Digital Imaging Division 145-3, Sangdaewon 1-Dong,

Jungwon-Gu,Sungnam,Kyungki-Do,Korea462-703

TEL:82-31-740-8137~41 FAX:82-31-740-8145

•SAMSUNG OPTO-ELECTRONICS AMERICA, INC. (SOA)

Closed Circuit Division 40 Seaview Drive, Secaucus NJ 07094,

U.S.A

TEL: (201) 902-0347 FAX:(201)902-0429

•SAMSUNG OPTO-ELECTRONICS UK LTD (SOUK)

Samsung House, 1000 Hillswood Drive Hillswood Business

ParkChertseySurreyKT16OPS

TEL:44-(0)1932-45-5308 FAX:44-(0)1932-45-5325

•

TIANJINSAMSUNGOPTO-ELECTRONICSCO.,LTD(TSOE)

7PingchangRd,NankaiDist, Tianjin, P.R China

PostCode:300190

TEL: 86-22-2761-9698 FAX: 86-22-2761-6514

SALES NETWORK

www.samsungtechwin.com

www.samsungcctv.com

This installation should be made by a qualified service

person and should conform to all local codes.

INFORMATION -This equipment has been tested and

found to comply with limits for a Class A digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference

to radio communications.

Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be

required to correct the interference at his own expense.

WARNING - Changes or modifications not expressly

approved by the manufacturer could void the user’s authority

to operate the equipment.

CAUTION -

To prevent electric shock and risk of fire hazards:

Do NOT use power sources other than that specified.

Do NOT expose this appliance to rain or moisture.

WARNING- TO PREVENT ELECTRIC SHOCK AND RISK OF FIRE HAZARDS,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

Thank you for purchasing a SAMSUNG CCD CAMERA. Before

operating the camera, confirm the camera model and proper

input power voltage. In order that you can understand this

manual thoroughly, we'll introduce our model description.

SOC-4020 Series (410,000 pixels)

• NTSC models • PAL models

SOC- 4020ND SOC- 4020PD

SOC- 4020NA SOC- 4020PA

SOC- 4020NDW SOC- 4020PDW

SOC- 4020NAW SOC- 4020PAW

Model Description

SOC- 4020 X X X

• Signal System

N NTSC Model

P PAL Model

• Power Source

D DC 12V

A AC 24V ~

• Lens Type

Blank 3.8~9.5mm

W 2.5~6.0mm

Power Source

Signal System

Lens Type

COLORCCD CAMERACOLORCCD CAMERA User’s ManualUser’s Manual

Features Contents

Auto Iris Vari-focal Lens Built-in

The focal length of lens is 3.8 to 9.5mm,

equivalent to 2.5x zoom.(2.5 to 6.0mm,

equivalent to 2.4x zoom) The built-in

lens allows the camera to have a Wider

Dynamic Range, therefore you can use

in various applications.

Fashionable and Stylish Design

Fashionable design is best suited to many

modern places moreover silver color adds

lusterto that.

High Resolution

The horizontal resolution of 480 TV lines

can be achieved by using a high density

CCD having effective 410,000 pixels,

which provides clean, noiseless and

reliablepictures.

Backlight Compensation

The backlight compensation technology

allows the camera to find the best picture

conditions in any environment and

automatically gives a necessary light level

compensation, so that you can always

obtain the clear picture, the finest detail

andperfect lightcontrast.

High Sensitivity

DSP LSI technology provides best picture

with min illumination of 0.5Lux / F1.2

(30IRE).

White Balance (ATW)

ATW function allow the camera to

adjust the white balance automatically

in response to light conditions.

SYNC. System

Youcan selectINT(Internal Synchronization)

modeor L.L(Linelock Synchronization)mode.

(SOC-4020SERIES)

Front

Back

Bottom

Lens

Connecting To Monitor

Connecting To Power

Precautions

Composition

Name and Function of Each Part

Connection

Troubleshooting

Specification

COLORCCD CAMERACOLORCCD CAMERA User’s ManualUser’s Manual

Precautions

Do not install the camera in

extreme temperature conditions.

Only use the camera under conditions

where temperatures are between -10˚C

and +50˚C. Be especially careful to provide

ventilation when operating under high

temperatures.

Do not install or use the camera in an

environment where the humidity is high.

Itcancausetheimagequalitytobepoor.

Do not install the camera under

unstable lighting conditions.

Severe lighting change or flicker can

cause the camera to work improperly.

Do not touch the front lens of

the camera.

It is one of the most important parts of

the camera. Be careful not to be stained

by fingerprint.

Do not drop the camera or

subject them to physical shocks.

It can cause malfunctions to occur.

Never keep the camera face to

strong light directly.

It can damage the CCD.

Do not expose the camera to

rain or spill beverage on it.

If it gets wet, wipe it dry immediately.

Liquids can contain minerals that corrode

the electronic components.

• If the camera is exposed to spotlight or object reflecting strong light, smear or

blooming may occur.

• Please check that the power satisfies the normal specification before connecting

the camera.

Notes

COLORCCD CAMERACOLORCCD CAMERA User’s ManualUser’s Manual

Composition

1. Color CCD Camera SOC-4020

2. Instruction Manual

Front

Lens Built-in

Vari-focal Lens built-in camera.

Control Cover

Used to access focus or zoom handle. After access, be sure to close it.

Focus Handle

Used to providefor accurate focusing of an objectwithinthelensfieldofview.

Zoom Handle

Used to adjustzoommagnification by turning.

Name and Function of Each Part

COLORCCD CAMERACOLORCCD CAMERA User’s ManualUser’s Manual

1110

Back

Video Out Jack

Connecttothevideo input connector of monitor. Thisjackoutputsa

composite video signal. Use a coaxial cable for connection.

DC Level Adjustment V.R

Used to adjust video output level of DC driven auto iris lens. When the

brightness control of the monitor does not operate correctly, you can get the

optimum picture by controlling the DC level of camera.

V. PHASE Adjustment V.R: AC type

If the camera is to be used in the LL mode, the vertical phase may require

adjustment to synchronize the vertical phase of the camera with other camera

in the system. Make this adjustment when the vertical phase of the camera

does not match with other cameras or systems. For correct adjustment, use a

multi-channeloscilloscope. The V. PHASE adjustment canbereadjusted.

Power Input Terminal

UsedtoconnectAC/DC power source.

Power Lamp

Thepowerlampturns on when power is properlysupplied.

Function Selection Switch

(1) BLC(Backlight Compensation) ON/OFF Switch

This switch improves an image that is darkened because of backlighting.

When the lighting source is in the rear of an object, the object might be seen

somewhat dark. If you want to see the object clearly, turn this switch ON.

The effective area where backlight compensation is activate is fixed in the

centerof the screen.

Monitor Picture Adjustment direction

To make it brighter Turn clockwise

Monitor Picture Adjustment direction

To make it darker

Turn counterclockwise

• This adjustment is necessary only when linelock is performed.

• There is no V. PHASE adjustment VR on the rear of DC power type.

Notes

Name and Function of Each Part

* Use the select switches on the rear of camera.

*This diagram is based on SOC-4020Series

COLORCCD CAMERACOLORCCD CAMERA User’s ManualUser’s Manual

1312

Name and Function of Each Part

(2) White Balance Control Mode

•ATW(Auto Tracing White balance): The camera automatically controls the

white balance in any environment.

•AWC(Auto White balance Control): The white balance is automatically

adjusted in a specific environment.

(3) Sharpness

Theswitch emphasize the sharpness. Tosoften the edgeturn this switch off.

(4) Flickerless

Flickerless function. In this function, electronic shutter is fixed in 1/100sec

(1/120sec: PAL model). FL function can compensate the flicker caused by

power frequency, but set OFF in the area not using a 60Hz (50Hz: PAL

model)AC Power.

(5) INT/LL Switch: SOC-4020Series

Used to choose INT or LL mode.

•INT(Internal) mode :The camera may be operated independently with its

internal crystal control.

• LL(Linelock) mode : It synchronizes the video signal between cameras using

thefrequencyofthe AC power supply without external synchronousgenerator.

(6) Not Used

• The LL mode can be used in the areas of 60Hz(NTSC models), 50Hz(PAL models).

Notes

Bottom

You can remove and install this bracket on the top of

the camera. You must use the supplied screw or the

equivalent (within 6mm). If not, the bracket may not

be fixed properly.

Tripod Mounting Hole

Usedto install the camera onan optional tripod.

Thetripod must be equipped withthe screw

specifiedas shown below.

1/4"-20 UNC (20 THREAD)

L:4.5mm±0.2mm (ISO standard),

or 0.197" (ASA standard)

COLORCCD CAMERACOLORCCD CAMERA User’s ManualUser’s Manual

1514

Connection

LENS

TheDC lens is supplied withthis camera.

•Ifthe lensis markedwith fingerprintsor othermarks,the imagequality mightbe poor.

•It is recommended to use the built-in iris lens to improve the image quality under low

illumination.

Notes

Connect the VIDEO out jack to the monitor video in jack.

Connecting to Monitor

CCD Camera Monitor

•As the connecting method varies with the instruments, refer to the manual

supplied with the instrument.

• Connect the cable after power is turned off.

•

Setthe75Ω/ Hi-Z selection switch asshown below ifyou have anintermediate device.

CCD Camera Intermediate End monitor

Connecting to Power

Each model has different power specification, please check the name of the model

and power specification before connecting to power source.

Please refer to the sticker identifying the model, which is attached on the product,

for power specification.

• The wire is polarized. Be careful of polarity.

• Use DC 12V power source for SOC-4020SERIES

Resistance of copper wire [at 20C˚ (68˚F)]

•As voltage may drop according to the length of electric cord as above table, a

cameramay malfunction if too longoutput line ofadaptor is connected to the

camera.

* Voltage for camera operation: DC 12V ± 10%

* Voltage drops on above table are variable according to types of electric cord and makers.

For DC Power Type

Copper wire size (AWG)

#24(0.22mm2)#22(0.33mm2)#20(0.52mm2)#18(0.83mm2)

Resistance ( Ω/ m) 0.078 0.050 0.030 0.018

Voltage Drop (V/m) 0.028 0.018 0.011 0.006

COLORCCD CAMERACOLORCCD CAMERA User’s ManualUser’s Manual

1716

Connection

• The wire is non-polarized.

• Use AC24V ~ 60Hz power source for SOC-4020NA/W

• Use AC24V ~ 50Hz power source for SOC-4020PA/W

For AC Power Type

• Be sure to connect power after all the installation is done.

• Note that AC adaptor is not supplied with camera.

• Use only AC 24V UL listed class 2 power supply.

• Since the wire of DC power type is polarized, be careful when connecting it.

• Do not use power sources other than that specified.

• To prevent fire or electric shock hazard, use a UL listed cable (VW-1, Style 1007).

Notes

If you have trouble operating your camera, refer to the following table. If the

guidelines do not enable you to solve the problem, contact an authorized

technician.

Problem

Nothing appears on

the screen.

The image on the

screen is dim.

The image on the

screen is dark.

The camera is not working

properly, and the surface

of the camera is hot.

The image on the

screen flickers.

L/L mode isn’t able to

be selected.

Solution

•Check that the power cord and line connection

betweenthe camera andmonitorare fixedproperly.

•Check that you have properly connected VIDEO

cabletothecameraVIDEO output jack.

•Is lens stained with dirt? Clean your lens with soft,

clean cloth.

• Set the monitor to proper condition.

•If the camera is exposed to too strong light, change

the camera position.

• Adjust the lens’ focus properly.

•Adjustthecontrastfeatureofthemonitor.

•If you have an intermediate device, set the 75Ω/ Hi-z

properly.(refer topage14)

•AdjustDCLevel,VR Level properly (refer to page 10)

•Check that you have properly connected the camera

to an appropriate power source. (refer to page 15)

• Is the camera facing to direct sunlight or fluoresent

lighting? Change the camera position.

•Have you connected your camera to DC power

source? Connect it to AC power source.

(SOC-4020Series)

Troubleshooting

COLORCCD CAMERA User’s Manual

Specifications

SOC-4020NA/W SOC-4020ND/W SOC-4020PA/W SOC-4020PD/W

Item

Power Source

Power Consumption

Synchronization

Image Pick-up Device

Total Pixels

Effective Pixels

Scanning

Min. Illumination

Resolution

Video Output

Scanning Frequency

AGC

White Balance

BLC Function

Sharpness

Flickerless

Lens Type

S/N Ratio

Operating Temperature

Dimention

Weight (Without Lens)

INT/LL Selectable

(0~270˚ Adjustable)

INT

INT/LL Selectable

(0~270˚ Adjustable)

INT

AC 24V, 60Hz DC 12V AC 24V, 50Hz DC 12V

3.5W (Max) 2.5W (Max) 3.5W (Max) 2.5W (Max)

1/3” Color Interline-Transfer CCD

816(H) x 494(V) 798(H) x 584(V)

771(H) x 492(V) 753(H) x 582(V)

2:1 Interlace

0.5Lux / F1.2 (30IRE)

480 TV Line

VBS ; 1Vp-p, 75Ωunbalanced

15.734KHz(H) / 60Hz(V) 15.625KHz(H) / 50Hz(V)

Built in

ATW / AWC Selectable

ON / OFF Selectable

High / Normal Selectable

ON / OFF Selectable (ON: 1/100sec) ON / OFF Selectable (ON: 1/120sec)

more than 48dB (weight ON)

-10˚C ~ +50˚C [14˚F~122˚F] / 30% ~ 90%RH

62(W) x 58(H) x 165(D)mm

300g 290g 300g 290g

* Design and specifications are subject to change without notice

DECLARATION OF CONFORMITY

Application of Council Directive(s) 89 / 336 / EEC

Manufacturer's Name SAMSUNG TECHWIN CO., LTD

Manufacturer's Address SAMSUNG TECHWIN CO., LTD

42, SUNGJU-DONG CHANGWON-CITY,

KYUNGNAM, KOREA, 641-120

European Representative Name

European Representative Address

Equipment Type/Environment CCTV Camera

Model Name SOC-4020Series

Beginning Serial NO. S3900001

Year of Manufacture 2003. 9. 1

Conformance to EN 50081-1 : 1992

EMC-Directive 89/336 EEC and 92/31/EEC

EN 50130-4 : 1996

We, the undersigned, hereby declare that the equipment specified above conforms

totheaboveDirective(s).

Manufacturer SAMSUNGTECHWINCO.,LTD

LegalRepresentativeinEurope

Signature Signature

FullName YOUNGTAEKSON FullName

Position QUALITYCONTROLMANAGER Position

Place CHANGWON,KOREA Place

Date 2003.9.1 Date

Blank : X2.5 vari-focal, f=3.8~9.5, F=1:1.3~2.0

W Series : X2.4 vari-focal, f=2.5~6.0, F=1:1.3~2.0

(DC Iris Lens adjustable)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Samsung Sicherheitskamera Handbücher

Samsung

Samsung SCP-2371 Bedienungsanleitung

Samsung

Samsung SCC-100BP Bedienungsanleitung

Samsung

Samsung SCP-3370TH Bedienungsanleitung

Samsung

Samsung BW-4302 Series Bedienungsanleitung

Samsung

Samsung SND-L6013 Bedienungsanleitung

Samsung

Samsung SNB-6010A Bedienungsanleitung

Samsung

Samsung SND-5080 Bedienungsanleitung

Samsung

Samsung SCC-B5344 Bedienungsanleitung

Samsung

Samsung SCO-2080RH Bedienungsanleitung

Samsung

Samsung SCD-6023R Bedienungsanleitung

Samsung

Samsung SCC-B2303(P) Bedienungsanleitung

Samsung

Samsung iPolis SNP-3300A Bedienungsanleitung

Samsung

Samsung SCC-B9371 Bedienungsanleitung

Samsung

Samsung SCC-931TP Bedienungsanleitung

Samsung

Samsung SNC-550 iPOLiS Bedienungsanleitung

Samsung

Samsung HCD-E6070R Bedienungsanleitung

Samsung

Samsung SCP-3370TH Bedienungsanleitung

Samsung

Samsung SID-500 Bedienungsanleitung

Samsung

Samsung SCP-2273 Bedienungsanleitung

Samsung

Samsung SCC-A2033P Bedienungsanleitung

Samsung

Samsung SID-53 Bedienungsanleitung

Samsung

Samsung SCC-C4301 Bedienungsanleitung

Samsung

Samsung SNP-6200 Bedienungsanleitung

Samsung

Samsung SCC-C7478 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung