S&C TripSaver Betriebsanleitung

May 22, 2017

S&C TripSaver®Dropout Recloser

Outdoor Distribution (15 kV and 25 kV)

Table of Contents

Section Page Section Page

Introduction

Qualified Persons ..............................2

Read this Instruction Sheet ......................2

Retain this Instruction Sheet......................2

Proper Application..............................2

Warranty .....................................3

Safety Information

Understanding Safety-Alert Messages ..............4

Following Safety Instructions .....................4

Replacement Instructions and Labels...............4

Location of Safety Label ........................5

Safety Precautions.............................6

Packing and Inspection

Packing ......................................7

Inspection ....................................7

Handling .....................................7

Installation ................................8

Operation

If TripSaver Dropout Recloser Has Dropped Out .....14

If Line Work Is to Be Performed Downstream

of TripSaver Dropout Recloser .................16

Operation Counter ............................17

Service .....................................17

Under Ice Conditions ..........................17

Service Soon Indicator .........................18

Overload Ratings .............................18

Contact Position Indicator .......................18

Operation with Loadbuster®—The S&C Loadbreak

Tool .....................................19

Installation and Operation

2S&C Instruction Sheet 461-500

Qualified Persons WARNING

The equipment covered by this publication must be installed, operated, and maintained

by qualified persons who are knowledgeable in the installation, operation, and main-

tenance of overhead electric power distribution equipment along with the associated

hazards. A qualified person is one who is trained and competent in:

• The skills and techniques necessary to distinguish exposed live parts from non-live

parts of electrical equipment

• The skills and techniques necessary to determine the proper approach distances cor-

responding to the voltages to which the qualified person will be exposed

• The proper use of the special precautionary techniques, personal protective equipment,

insulating and shielding materials, and insulated tools for working on or near exposed

energized parts of electrical equipment

These instructions are intended only for such qualified persons. They are not intended

to be a substitute for adequate training and experience in safety procedures for this type

of equipment.

Read this

Instruction Sheet

Thoroughly and carefully read this instruction sheet before installing or operating your

S&C TripSaver Dropout Recloser. The latest version is available online in PDF format at www.

sandc.com. Select: Support/Product Literature Library. Familiarize yourself with “SAFETY

INFORMATION” on pages 4–6.

Retain this

Instruction Sheet

This instruction sheet should be available for reference wherever the TripSaver Dropout

Recloser is used. Retain this instruction sheet in a location where you can easily retrieve

and refer to it.

Proper Application CAUTION

TripSaver Dropout Recloser must only be used for specific fusing applications that are

within the ratings of the model selected. TripSaver Dropout Recloser ratings are listed on

a ratings label attached to the unit.

NOTICE

When retrofitting TripSaver Dropout Recloser in an existing cutout mounting: To

ensure proper performance, TripSaver Dropout Recloser must only be installed in a

current-production (“-R10” catalog number supplement) S&C Type XS Cutout mounting.

See Figure 1. The warranty set forth in S&C Price Sheet 150 does not apply if TripSaver

Dropout Recloser is installed in an earlier-production S&C mounting, as shown in Figure 2,

or another manufacturer’s cutout mounting.

Introduction

S&C Instruction Sheet 461-500 3

Introduction

Warranty The warranty and/or obligations described in S&C’s standard conditions of sale, as set forth

in Price Sheet 150, plus any special warranty provisions, as set forth in the applicable product-

line specication bulletin, are exclusive. The remedies provided in the former for breach of

these warranties shall constitute immediate purchaser’s or end user’s exclusive remedy and

a fulllment of all seller’s liability. In no event shall seller’s liability to immediate purchaser

or end user exceed the price of the specic product which gives rise to immediate purchaser’s

or end user’s claim. All other warranties whether express or implied or arising by operation

of law, course of dealing, usage of trade or otherwise, are excluded. The only warranties are

those stated in Price Sheet 150, and THERE ARE NO EXPRESS OR IMPLIED WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ANY EXPRESS

WARRANTY OR OTHER OBLIGATION PROVIDED IN PRICE SHEET 150 IS GRANTED ONLY

TO THE IMMEDIATE PURCHASER AND END USER, AS DEFINED THEREIN. OTHER THAN

AN END USER, NO REMOTE PURCHASER MAY RELY ON ANY AFFIRMATION OF FACT OR

PROMISE THAT RELATES TO THE GOODS DESCRIBED HEREIN, ANY DESCRIPTION THAT

RELATES TO THE GOODS, OR ANY REMEDIAL PROMISE INCLUDED IN PRICE SHEET 150.

Figure 1. Current-production (“-R10” catalog number supplement)

S&C Type XS Fuse Cutout mounting.

Figure 2. Earlier-production (“-R9” catalog number supplement)

S&C Type XS Fuse Cutout mounting. “-R8” and earlier versions

have similar upper contact.

4S&C Instruction Sheet 461-500

Safety Information

Understanding

Safety-Alert

Messages

Several types of safety-alert messages may appear throughout this instruction sheet as well

as on labels attached to the crate, packing, and equipment. Familiarize yourself with these

types of messages and the importance of the various signal words, as explained below.

DANGER

“DANGER” identifies the most serious and immediate hazards that will likely result in

serious personal injury or death if instructions, including recommended precautions, are

not followed.

WARNING

“WARNING” identifies hazards or unsafe practices that can result in serious personal

injury or death if instructions, including recommended precautions, are not followed.

CAUTION

“CAUTION” identifies hazards or unsafe practices that can result in minor

personal injury if instructions, including recommended precautions, are not followed.

NOTICE

“NOTICE” identifies important procedures or requirements that can result in product or

property damage if instructions are not followed.

Following Safety

Instructions

If you do not understand any portion of this instruction sheet and need assistance,

contact your nearest S&C Sales Office or S&C Authorized Distributor. Their

telephone numbers are listed on S&C’s website sandc.com Or call S&C Headquarters

at (773) 338-1000; in Canada, call S&C Electric Canada Ltd. at (416) 249-9171.

NOTICE

Thoroughly and carefully read this instruction sheet

before operating your S&C TripSaver Dropout Recloser.

Replacement

Instructions

and Labels

If you need additional copies of this instruction sheet, contact your nearest S&C Sales Ofce,

S&C Authorized Distributor, S&C Headquarters, or S&C Electric Canada Ltd.

It is important that any missing, damaged, or faded labels on the equipment be replaced

immediately. Replacement labels are available by contacting your nearest S&C Sales Office,

S&C Authorized Distributor, S&C Headquarters, or S&C Electric Canada Ltd.

S&C Instruction Sheet 461-500 5

Safety Information

Reorder Information for Safety Information

Safety Alert Message Description Part Number

DANGER TripSaver may be energized from either side and in any position. Always consider all parts live until

de-energized, tested, and grounded G-9248

Location of Safety Labels

G-9248-E

ÇDANGER

TripSaver®II may be energized

from either side and in any

position. Always consider all

parts live until de-energized,

tested, and grounded.

6S&C Instruction Sheet 461-500

Safety Precautions

DANGER

TripSaver Dropout Reclosers operate at high voltage. Failure to observe the precau-

tions below will result in serious personal injury or death.

Some of these precautions may differ from your company’s operating procedures and

rules. Where a discrepancy exists, follow your company’s operating procedures and rules.

1. QUALIFIED PERSONS. Access to TripSaver Dropout

Reclosers must be restricted only to qualified persons.

See “Qualified Persons” on page 2.

2. SAFETY PROCEDURES. Always follow safe operating

procedures and rules.

3. PERSONAL PROTECTIVE EQUIPMENT. Always use

suitable protective equipment such as rubber gloves,

rubber mats, hard hats, safety glasses, and flash clothing

in accordance with safe operating procedures and rules.

4. SAFETY LABELS AND TAGS. Do not remove or

obscure any of the“DANGER,”“WARNING,”“CAUTION,”

or “NOTICE” labels and tags. Remove tags ONLY if

instructed to do so.

5. ENERGIZED COMPONENTS. Always consider all

parts live until de-energized, tested, and grounded.

6. OPERATING TOOLS. To close a TripSaver Dropout

Recloser, use a conventional insulated hookstick or

S&C Universal Pole and Pole Extension fitted with an

S&C Talon™ Handling Tool or a distribution prong. To

open the TripSaver Dropout Recloser, use a

Loadbuster®—The S&C Loadbreak Tool, attached to a

conventional insulated hookstick or S&C Universal Pole.

7. MAINTAINING PROPER CLEARANCE. Always

maintain proper clearance from energized components.

S&C Instruction Sheet 461-500 7

Shipping and Handling

Packing

A complete S&C TripSaver Dropout Recloser includes the

following:

1. A single-pole TripSaver Dropout Recloser.

2. Miscellaneous mounting hardware (less through-bolts)

for securing the TripSaver Dropout Recloser to the pole.

Inspection

Examine the shipment for external evidence of damage as

soon after receipt as possible, preferably before removal

from the carrier’s conveyance. Check the bill of lading to

make sure that shipping skids, crates, and containers listed

thereon are present:

If there is visible loss and/or damage:

1. Notify the delivering carrier immediately.

2. Ask for a carrier inspection.

3. Note condition of shipment on all copies of the delivery

receipt.

4. File a claim with the carrier.

If concealed damage is discovered:

1. Notify the delivering carrier within 15 days of receipt of

shipment.

2. Ask for a carrier inspection.

3. File a claim with the carrier.

Also notify S&C Electric Company in all instances of loss

and/or damage.

Handling

CAUTION

DO NOT drop TripSaver Dropout Recloser or subject

any parts to undue stress during installation.

8S&C Instruction Sheet 461-500

Installation

STEP 1. For Overhead Pole-Top Style TripSaver Dropout

Reclosers: Attach the mounting to its mounting

bracket as illustrated in Figure 3. A mounting

bracket—suitable for crossarm, pole, or wall

mounting—is furnished only if specied through

the addition of sufx “-B” or “-C” to the TripSaver

Dropout Recloser catalog number. Note the

placement of the external-tooth lockwasher

between the mounting bracket and the center insert

of the mounting. Pivot the mounting to a position

that will provide maximum ease of operation,

then securely tighten the carriage bolt nut.

For Branch Feeder Style TripSaver Dropout

Reclosers: Attach the mounting base support to the

crossarm(s) or structure. A backup member with

carriage bolts, at washers, lockwashers, and nuts

is furnished only if specied through the addition of

sufx “-D1,” “-D2,” “-D3,” or “-D4” to the TripSaver

Dropout Recloser catalog number.

Carriage bolt

Carriage bolt nut

Lockwasher

Mounting bracket Overhead pole-top

mounting center insert

External tooth

lockwasher

Figure 3. Attaching Overhead Pole-Top Style TripSaver Dropout

Recloser mounting to mounting bracket.

S&C Instruction Sheet 461-500 9

Installation

Lifting eye

Figure 4a. Inserting 15-kV TripSaver Dropout Recloser into

mounting.

Figure 4b. Inserting 15-kV TripSaver Dropout Recloser into

mounting.

Figure 4c. Inserting 15-kV TripSaver Dropout Recloser into

mounting.

STEP 2. Make electrical connections to the mounting. If

aluminum conductors are used, be sure to wire-

brush them, then apply a coating of oxidation

inhibitor before inserting them into the connectors.

STEP 3. a) Insert 15-kV TripSaver Dropout Recloser into the

mounting by hand as shown in Figures 4a and 4b.

Alternately, while in a bucket and using a short hot

stick, insert the curled prong of an S&C Talon

Handling Tool or a distribution prong into the

lifting eye on the trunnion, and raise TripSaver

Dropout Recloser into the mounting. See Figure 4c.

If a Talon tool is used, rotate the universal pole

counterclockwise 180° to disengage it.

10 S&C Instruction Sheet 461-500

Figure 5d. Inserting 15/27-kV TripSaver Dropout Recloser into

mounting.

Figure 5c. Inserting 15/27-kV TripSaver Dropout Recloser into

mounting.

Figure 5b. Inserting 15/27-kV TripSaver Dropout Recloser into

mounting.

Figure 5a. Inserting 15/27-kV TripSaver Dropout Recloser into

mounting.

Installation

b) Insert 15/27-kV TripSaver Dropout Recloser into

the mounting by hand as shown in Figures 5a and

5b. Ensure that the end of the trunnion slides under

the connector bracket, as shown in Figure 5d. This

allows the trunnion to be lowered into the hinge.

Alternately, insert the curled prong of an S&C Talon

Handling Tool or a distribution prong into the lifting

eye on the trunnion, and raise TripSaver Dropout

Recloser into the mounting. See Figures 5c and

5d. If a Talon tool is used, rotate the universal pole

counterclockwise 180° to disengage it.

Inhaltsverzeichnis

Andere S&C Industrieelektrik Handbücher

S&C

S&C TripSaver II Kurzanleitung

S&C

S&C TripSaver II Bedienungsanleitung

S&C

S&C Mark VI Leitfaden

S&C

S&C Scada-Mate SD Betriebsanleitung

S&C

S&C TripSaver II Kurzanleitung

S&C

S&C Vista SD Bedienungsanleitung

S&C

S&C TripSaver II Bedienungsanleitung

S&C

S&C IntelliRupter PulseCloser Bedienungsanleitung

S&C

S&C Vista Series Bedienungsanleitung

S&C

S&C IntelliRupter PulseCloser Bedienerhandbuch

S&C

S&C IntelliRupter PulseCloser Bedienungsanleitung

S&C

S&C IntelliRupter PulseCloser Bedienungsanleitung

S&C

S&C PMH Series Bedienungsanleitung

S&C

S&C TripSaver II Betriebsanleitung

S&C

S&C IntelliRupter PulseCloser Fault Interrupter Bedienungsanleitung

Beliebte Industrieelektrik Handbücher anderer Marken

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Technisches Handbuch

Abtech

Abtech HVJB Series Leitfaden

Murata

Murata GRM0335C1H8R1DA01 Series Bedienungsanleitung

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Bedienungsanleitung

Eaton

Eaton Ulusoy HMH24-04 Bedienungsanleitung

Murata

Murata GJM0335C1E4R4BB01 Series Bedienungsanleitung

Newlong

Newlong NP-7H Bedienungsanleitung

Stahl

Stahl 8575/12 Bedienungsanleitung

SI Pegasus Bedienungsanleitung

Murata

Murata GRM1555C1H2R7CA01 Seies Bedienungsanleitung

Murata

Murata GRM0225C1E6R4BA03 Series Bedienungsanleitung

Cooper Power Systems

Cooper Power Systems VXE15 Bedienungsanleitung

Murata

Murata GRM0335C2A7R3CA01 Series Bedienungsanleitung

Siemens

Siemens 3VA9988-0BM10 Bedienungsanleitung

Siemens

Siemens SITRANS LVS100 Bedienungsanleitung

Murata

Murata GRM32ER60G227ME05 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MP-Series Bedienungsanleitung

Phasemation

Phasemation DG-100 Bedienungsanleitung