Sanus CFR2100 Series Bedienungsanleitung

CFR2115, CFR2127, CFR2136, CFR2144

Instruction Manual

We’ll Make It Stress-Free

If you have any questions along the way, just give us a call.

1-800-359-5520. We’re ready to help!

Scan for more information

san.us/891

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the

damaged item to your dealer; contact Customer Service. Never use damaged parts!

Supplied parts are located inside of the rack. To access the parts, remove the back panel.

Thank you for choosing a Sanus Component Series Rack. The CFR2100 series is designed to support audio/video equipment.

The total weight capacity for the CFR2100 series:

CFR2115 226.8 kg (500 lb)

CFR2127 340.2 kg (750 lb)

CFR2136 385.5 kg (850 lb)

CFR2144 453.6 kg (1,000 lb)

Each 2U shelf supports up to 22.6 kg (50 lb), and each 1U shelf supports up to 13.6 kg (30 lb).

Each optional 3U shelf supports up to 36.2 kg (80 lb).

CAUTION: Avoid potential personal injuries and property damage!

•Do not exceed the stated weight capacities.

•Do not shake, tilt, rock, sit, stand, or climb on your Component Series Rack. Tipping may cause injury or death.

•Do not move large racks by yourself; due to weight and height, assistance is required.

•To avoid instability do not pull out more than one optional drawer or slide out equipment at a time.

•Before moving, make sure all optional drawers and slide out equipment are secured and door is closed and secured.

•Use extreme caution when moving a loaded rack! Push, DO NOT pull, loaded rack slowly over a short, smooth, level distance. Avoid

sudden starts and stops to minimize the strain placed on casters.

•Do not use this product for any purpose not explicitly specified by manufacturer.

•If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this product,

contact manufacturer Customer Service or call a qualified contractor.

•Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.

NOTE: Due to continuous product improvement, images shown in this manual may vary from actual product.

IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE MANUAL PRIOR TO USE

Do you have all of the tools needed?

Unpacking

Parts and Hardware

CFR2115 8

CFR2127 12

CFR2136 16

CFR2144 18

CFR2115 4

CFR2127 6

CFR2136 8

CFR2144 9

CFR2115 8

CFR2127 8

CFR2136 8

CFR2144 8

M5 x 10 mm 10-32 x 3/4 in.

CFR2115 4

CFR2127 8

CFR2136 12

CFR2144 16

05 06

01 x1

02 x2

CAUTION: Failure to follow loading requirements could lead to instability causing personal injury and/or property damage:

To prevent instability:

• Always load the rack from the bottom up and load the heaviest item first.

• 50% of the total weight should be mounted in the lower 1/3 of the rack.

Load Your Components

CAUTION: Failure to follow loading requirements could lead to instability causing personal injury and/or property damage:

To prevent instability:

• Always load the rack from the bottom up and load the heaviest item first.

• 50% of the total weight should be mounted in the lower 1/3 of the rack.

• Follow these additional requirements when loading rack on its back and then lifting rack to an upright position:

1. Leveling feet, if installed, need to be adjusted all the way in.

2. You must not load more than 20% of the total rated load prior to lifting rack to upright position.

3. All equipment should be securely fastened to the rack.

4. Use caution when lifting rack to upright position as casters may roll. Assistance is required.

2 / 3

OPT

Rack Shelf Backstops

NOTE: rear view with back panels removed.

1. Insert backstop 03 into slot behind component.

2. Slide backstop 03 forward until firmly against component and twist 90 degrees.

Component Straps

NOTE: side view with panels removed.

A. Slide straps 04 through slots in sides of shelves.

B. Wrap straps 04 over component to secure.

Using Backstops and Component Straps

A B

OPT

Access Panels for Cable Management

OPT

CAUTION: Avoid damage to your components due to overheating. Make sure that there is adequate space between each unit for

proper airﬂow. Operating temperature inside the rack must not exceed 104°F (40°C).

To install fan:

Remove the vented panel. CAUTION: Cut edges may be sharp.

Remove any metal burrs that remain in the panel frame. Mount the cooling fan using the screws 05 included.

Install Fan for Additional Ventilation (Top or Bottom)

OPT

05 05

Adjust Shelves and Blanking Panels

L L

NOTE: Align the bottom of the shelf or blanking panel Bwith the lines Lon the rack rail.

OPT

Adjust Rack Rails

OPT

Remove the shelves and blanking panels before adjusting the rails. Adjust the right and left rails evenly.

NOTE: For clarity, the front door, top, and side panels are not shown.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sanus Rack & Stand Handbücher

Sanus

Sanus BSSATM1 Bedienungsanleitung

Sanus

Sanus VM300 Bedienungsanleitung

Sanus

Sanus HTB7 Bedienungsanleitung

Sanus

Sanus VLF510 Bedienungsanleitung

Sanus

Sanus VLL10 Bedienungsanleitung

Sanus

Sanus VMA401 Bedienungsanleitung

Sanus

Sanus VLL5 Bedienungsanleitung

Sanus

Sanus VTM27 Montageanleitung

Sanus

Sanus CFR21 Series Bedienungsanleitung

Sanus

Sanus CFR1610 Bedienungsanleitung

Sanus

Sanus F80 Bedienungsanleitung

Sanus

Sanus SSASB2 Bedienungsanleitung

Sanus

Sanus WSSATM1 Bedienungsanleitung

Sanus

Sanus SAN55BA Bedienungsanleitung

Sanus

Sanus F107 Bedienungsanleitung

Sanus

Sanus VML5 Bedienungsanleitung

Sanus

Sanus SAN213 Bedienungsanleitung

Sanus

Sanus Sanus VisionMount ML22 Bedienungsanleitung

Sanus

Sanus DLT1 Bedienungsanleitung

Sanus

Sanus WMS3 Bedienungsanleitung

Sanus

Sanus BLF328 Bedienungsanleitung

Sanus

Sanus SAN18B Bedienungsanleitung

Sanus

Sanus VSL4 Bedienungsanleitung

Sanus

Sanus WSS21 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung