Sanus CFR2115 Bedienungsanleitung
CFR2115, CFR2127, CFR2136, CFR2144
Instruction Manual
We’ll Make It Stress-Free
If you have any questions along the way, just give us a call.
1-800-359-5520. We’re ready to help!
Scan for more information
san.us/891
2
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the
damaged item to your dealer; contact Customer Service. Never use damaged parts!
Supplied parts are located inside of the rack. To access the parts, remove the back panel.
Thank you for choosing a Sanus Component Series Rack. The CFR2100 series is designed to support audio/video equipment.
The total weight capacity for the CFR2100 series:
CFR2115 226.8 kg (500 lb)
CFR2127 340.2 kg (750 lb)
CFR2136 385.5 kg (850 lb)
CFR2144 453.6 kg (1,000 lb)
Each 2U shelf supports up to 22.6 kg (50 lb), and each 1U shelf supports up to 13.6 kg (30 lb).
Each optional 3U shelf supports up to 36.2 kg (80 lb).
CAUTION: Avoid potential personal injuries and property damage!
•Do not exceed the stated weight capacities.
•Do not shake, tilt, rock, sit, stand, or climb on your Component Series Rack. Tipping may cause injury or death.
•Do not move large racks by yourself; due to weight and height, assistance is required.
•To avoid instability do not pull out more than one optional drawer or slide out equipment at a time.
•Before moving, make sure all optional drawers and slide out equipment are secured and door is closed and secured.
•Use extreme caution when moving a loaded rack! Push, DO NOT pull, loaded rack slowly over a short, smooth, level distance. Avoid
sudden starts and stops to minimize the strain placed on casters.
•Do not use this product for any purpose not explicitly specified by manufacturer.
•If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this product,
contact manufacturer Customer Service or call a qualified contractor.
•Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
NOTE: Due to continuous product improvement, images shown in this manual may vary from actual product.
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS
PLEASE READ ENTIRE MANUAL PRIOR TO USE
Do you have all of the tools needed?
Unpacking
3
Parts and Hardware
CFR2115 8
CFR2127 12
CFR2136 16
CFR2144 18
CFR2115 4
CFR2127 6
CFR2136 8
CFR2144 9
CFR2115 8
CFR2127 8
CFR2136 8
CFR2144 8
M5 x 10 mm 10-32 x 3/4 in.
CFR2115 4
CFR2127 8
CFR2136 12
CFR2144 16
05 06
01 x1
02 x2
03
04
CAUTION: Failure to follow loading requirements could lead to instability causing personal injury and/or property damage:
To prevent instability:
• Always load the rack from the bottom up and load the heaviest item first.
• 50% of the total weight should be mounted in the lower 1/3 of the rack.
4
Load Your Components
5
Load Your Components
CAUTION: Failure to follow loading requirements could lead to instability causing personal injury and/or property damage:
To prevent instability:
• Always load the rack from the bottom up and load the heaviest item first.
• 50% of the total weight should be mounted in the lower 1/3 of the rack.
• Follow these additional requirements when loading rack on its back and then lifting rack to an upright position:
1. Leveling feet, if installed, need to be adjusted all the way in.
2. You must not load more than 20% of the total rated load prior to lifting rack to upright position.
3. All equipment should be securely fastened to the rack.
4. Use caution when lifting rack to upright position as casters may roll. Assistance is required.
1
4
2 / 3
OPT
6
Rack Shelf Backstops
NOTE: rear view with back panels removed.
1. Insert backstop 03 into slot behind component.
2. Slide backstop 03 forward until firmly against component and twist 90 degrees.
Component Straps
NOTE: side view with panels removed.
A. Slide straps 04 through slots in sides of shelves.
B. Wrap straps 04 over component to secure.
Using Backstops and Component Straps
04
1
A B
2
03
03
03
04
OPT
7
Access Panels for Cable Management
OPT
8
CAUTION: Avoid damage to your components due to overheating. Make sure that there is adequate space between each unit for
proper airflow. Operating temperature inside the rack must not exceed 104°F (40°C).
To install fan:
Remove the vented panel. CAUTION: Cut edges may be sharp.
Remove any metal burrs that remain in the panel frame. Mount the cooling fan using the screws 05 included.
Install Fan for Additional Ventilation (Top or Bottom)
OPT
05 05
9
Adjust Shelves and Blanking Panels
B
B
L L
NOTE: Align the bottom of the shelf or blanking panel Bwith the lines Lon the rack rail.
OPT
10
Adjust Rack Rails
OPT
Remove the shelves and blanking panels before adjusting the rails. Adjust the right and left rails evenly.
NOTE: For clarity, the front door, top, and side panels are not shown.
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Sanus Rack & Stand Handbücher
Sanus
Sanus SASB1 Bedienungsanleitung
Sanus
Sanus WSWMU Bedienungsanleitung
Sanus
Sanus VUEPOINT F55 Bedienungsanleitung
Sanus
Sanus WSEDM2 Bedienungsanleitung
Sanus
Sanus SSASB2 Bedienungsanleitung
Sanus
Sanus Secura QML12 Bedienungsanleitung
Sanus
Sanus 6901-170053 Bedienungsanleitung
Sanus
Sanus VSF716-B2 Bedienungsanleitung
Sanus
Sanus VTM27 Montageanleitung
Sanus
Sanus SECURA QSL12 Bedienungsanleitung
Sanus
Sanus CAPS27 Bedienungsanleitung
Sanus
Sanus WSWM21 Bedienungsanleitung
Sanus
Sanus WSEPM21 Bedienungsanleitung
Sanus
Sanus VisionMount VMPl50A Bedienungsanleitung
Sanus
Sanus WSSATM1 Bedienungsanleitung
Sanus
Sanus LR1A Bedienungsanleitung
Sanus
Sanus WSECS1-B2 Bedienungsanleitung
Sanus
Sanus CFR518RR Bedienungsanleitung
Sanus
Sanus CILT3-B1 Bedienungsanleitung
Sanus
Sanus HTBS Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
