Sanyo MCD-Z330F Bedienungsanleitung

INSTRUCTION MANUAL

CD Radio Cassette Recorder

MCD-Z330F

,’

,-..<-.

,., . ,, PRECAUTIONS

,. .& .*. a+-~. =..... . ... .>...-...:.

. ... ........... ...... :

CAUTION-INVISIBLE LASER RAOtATION WHEN OPEN ANOINTERLOCKS DEFEATEO.

AVOIOEXPOSURE TO BEAM.

AOVARSEL-USYNLIG LASER STRALING VED ABNING, NAR SIKKERHEOSAFBRYOERE ER

UOE AF FUNKTION, UNOGAUOS /+TTELSE FOR STRALING.

VARNING-OSYNLIG LASER STRALNING NAR OENNAOEL AR OPPNAD OCHSPARR AR

URKOPPIAO. STRALEN AR FARLIG. A

VORSICHT! -UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEL GEOFFNET

UNO ENN SICHERHEITSVERRIEGELUNG UBERBRUCKT 1ST. NICHT, OEM STRAHL

AUSSETZEN

VARO !-AvattaessalasuojalukAusohltettaessaolet alttimanakymanbmalleIasersdeilylle.

Alakalso sateeseen.

CAUTION- USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

THE COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT

PROPERLY QUALIFIED PERSONNEL.

The apparatus shall not be exposed to drip- -Sudden changes in the ambient temperature

ping or splashing. may cause condensation to form on the opti-

Do not use where there are extremes of tem- cal lens inside the unit. If this happens, take

perature (below 5“C or exceeding 350C). out the disc, leave the unit for about 1hour,

Because of the CD player’s extremely low and then proceed to operate.

noise and wide dynamic range, there might -Do not install this equipment in aconfined

be atendency to set the volume on the ampli- space, such as a book case or built in

fier unnecessarily high. Doing so may pro- cabinet.

duce an excessively large output from the -The rating label is located on the bottom of

amplifier which could damage your speakers. the unit.

-1-

CONTROLS

456789

ru+l+tl e‘) ‘? ‘3 1?

23 22 2i 20 19 18 i7 /6 /5

28 27 26 25

1. Bass expander button (BASSXPANDER)

2. Q-sound button (QSOUND)

3. Display

I4. Record button (REC)

5. Play button (PIA~

6. Rewind button (RE~

7. Fast forward button (FFWD)

8. Stop/Eject button (STOP/EJEC~

9. Pause button (PAUSE)

10. Telescopic aerial

11. Cassette holder

12. Radio band button (BAND)

13. Preset button (PRESET)

14. Memoty button (MEMORY)

15. Volume control (VOLUME)

16. CD compartment opening button (CD OPEN)

17. Repeat /FM mode button (REPEAT/FM ~

MODE)

18. Tuning up/Skip/Search button (TUNING UP/ ~

SKIP/SEARCH)

19. Play/ Pause button (PIAY/PAUSE)

20. CD compartment :

21. Stop/Clear button (STOP/CLEAR)

22. Tuning down/Skip/Search button (TUNING ‘

DOWN/SKlp/SEARCH)

23. Function switch (TAPE/CD/RADIO)

24. Remote sensor (IR) “,

25. AC input socket (AC INPUT ,

<’

26. Headphones socket (PHONES)

27. Battery compartment lid :

28. Beat cancel switch (BEAT CANCEL) 4

-2- ..

POWER SUPPLY

AC POWER

Connect one end of the mains lead to the AC lN-

PUT socket and the other end to an AC outlet.

Note:

-The installed batteries are automatically dis-

connected when the mains lead is connected

to the unit

-The function (lAPE/CD/RADIO) switch is

mounted on the secondary side. The unit is

not disconnected from mains, even switched

off.

BAITERY POWER

Installing batteries

Install eight “D/R20” batteries (not supplied) as

shown below.

Battery

compartment

lid

,.” -.,

‘:

Cautions on batteries

To prevent battery electrolyte leakage, which may

result in injury and damage to the unit or other

objects, observe the following precautions:

1. All batteries must be installed with the proper $

polarity (see diagram on the rear of the unit).

2. Do not mix new with old or used batteries.

3. Only use batteries of the same type and

brand. .

4. Remove the batteries when they are not to be

used for along period time.

5. When the batteries have become discharged,

they must be disposed of in asafe manner

which complies with all applicable laws.

REMOTE CONTROL

——. .. ... ... ....... i.. .. . . .. .-..——.....——————— ----- ..-.

Controls 1.

Number buttons (1-9, O)

Play/ Pause button (PL4Y/PAUSE)

Memory button (MEMORY)

Radio band button (BAND)

Stop/ Clear button (STOP)

Volume buttons (VOLUME)

Preset button (PRESETI

Repeat/ FM mode button

(REPEAT/FM MODE)

Tuning/ Skip/Search buttons

(TUNING+, -/SKlP/SEARCH)

‘.

-3-

Number buttons (1-9, O)

If the function is “CD”, the buttons select the

track numbers on adisc.

If the function is”RADIO’’,the buttons select pre-

set radio stations.

With any other function,the buttons will not func-

tion.

i-Two buttons must always be pressed.

Example:

To select No.3, press O, then 3.

To select No.1 O, press 1, then O.

;To select No.25, press 2, then 5.

Installing batteries

Install two “AANR03” batteries (not supplied) as

shown below. IE2!ll

@) Q

GENERAL

..—.—----- ...%..... ... -. . ., . ...-.

Adjusting the volume

Turn the VOLUME control (or press the +or -

VOLUME button on the remote control). The vol-

ume level appears on the display (VOL Oto VOL

40).

Qsound button

Press the QSOUND button to ON. A3dimen-

sional sound effect is created.

Bass expander button

Press the BASSXPANDER button to ON to en-

hance the bass sound.

NOTE:

If the volume level is set to “VOL.30” or more, the

bass expander effect may reduce depending on

the input sources.

Headphones

Connect stereo headphones (not supplied) to the

PHONES socket for monitoring or for private

listening. The speakers are automatically discon-

nected when headphones are connected.

Remote control range

/r/- (

Remote control sensor

window

/1+ within WWOX.7meters

rll

7& {!j”

000

Oclo

‘a

OPERATION

. .. . . .. .,.,..,,-. --

The buttons on the re-

mote control perform

similar functions to simi-

larly marked buttons on

the front panel.

. ,. ...... .........,

WHAT TO DO IF ...

If the operation of the unit or display is not

normal.

Set the function (TAPE/CD/RADIO) switch to

CD or RADIO.

Disconnect the mains lead from the unit and

remove all batteries.

Press the BAND button on the front panel for

at least 1minute.

Connect the mains lead. and install all batter-

ies.

Operate the unit.

‘!

-4-

—

Use compact discs bearing the symbol shown

below. In addition to conventional 12 cm CDs,

this system can be used to play 8cm CDs with-

out an adapter.

~THg

DIGITAL AUDIO

Set the function (TAPE /CD/RADIO) switch to

CD.

Press the CD OPEN button. The CD compart-

ment opens.

Place the disc with the label facing upon the

turntable. (Place only one disc at atime.)

Label faci~g up \

Press the CD compartment to close it

The total playing time and total number of

tracks on the disc appear.

Press the PIAY/PAUSE button.

IlR I

. .../

-To start play from the desired track, se-

lect the track by using the SKIP/SEARCH

buttons (or number buttons on the re-

mote control), then press the PLAY/

PAUSE button. )

Note:

If adisc is loaded upside down, or if no disc

is loaded, the CD player will not operate.

Press the STOP/CLEAR button to end disc [

play.

When the last track has been played, the

player stops automatically.

To turn the CD cdaver off, set the function

switch to TAPEIOF;.

Note:

Do not open the CD compartment during CD

play. Always press the STOP/ CLEAR button and

wait for the disc to stop rotating before opening

the CD compartment.

Notes on handling compact discs

Do not expose the disc to direct sunlight,

high humidity or high temperatures for ex-

tended periods of time.

Discs should be returned to their cases after

use.

Do not apply paper or write anything on the

disc surface.

Handle the disc by its edge. Do not touch the

playing surface (glossy side).

Fingerprints and dust should be carefully

wiped off the playing surface of the disc with

asoft cloth.

Wipe in astraight motion from the centre to

the outside of the disc.

Never use chemicals such as record cleaning

sprays, antistatic sprays or fluids, benzene or

thinner to clean compact discs.

;

“➤“appears, and play starts from the first

track. The elapsed playing time for the cur-

rent track and track number are displayed.

-5-

Temporarily stopping play

Press the PLAY/PAUSE button. “➤“blinks. To

resume play, press the button again.

Skip play

To skip to track 6while track 3is playing, press

the” ➤M” SKIP/ SEARCH button repeatedly until

“6“appears (in the track section)on the display.

To skip back to track 3while track 6is playing,

press the “14< “SKIP/ SEARCH button repeat-

edly until “3“appears.

-The number buttons on the remote control

can also be used for skip play. To skip to

track 6while one track is @laying, press O,

then 6.

Search (forward/reverse)

If the “➤N“or “K< “SKIP/SEARCH button is

pressed during play, the player will search at high

speed in the forward or reverse direction while

the button is being pressed. When the button is

released, normal play will continue.

Repeat play

Press the REPEAT button before or during play.

The player will play all the tracks or all the pro-

grammed tracks repeatedly. “REP” appears. To

cancel repeat play, press the REPEAT button

again. “REP” disappears.

PROGRAMMED PLAY

Up to 20 tracks on adisc can be programmed tor

play in any order.

To begin the programming procedure, select

“CD” function first.

The same track can be programmed more

than once.

Load adisc that you want to programme be-

fore starting programmed play.

Press the STOP/CLEAR button.

Press the MEMORY button.

Y1-.;

\MW lR J

Select atrack by using the SKIP/SEARCH

buttons.

-The number buttons on the remote con-

trol can also be used.

IMU lR J

Press the MEMORY button. “MEM” remains lit.

Repeat steps 3-4 to programme additional

tracks.

Press the PLAY/PAUSE button to start play.

When all programmed tracks have been

played, the player stops automatically.

-The programme contents are retained in

memory.

Any attempt to programme more than 20

tracks will result in “FULL” being displayed

and discontinuation of the programming.

To cancel programmed play, press the STOP/

CLEAR button twice.

Checking the programme

Each time the MEMORY button is pressed in the

stop mode, the programmed details sequentially

appear on the display.

-6-

LISTENING

Set the function (TAPE /CD /RADIO) switch

to TAPE.

Press the STOP/ EJECT button. The cassette

holder opens.

Load the cassette into the cassette holder.

18After loading the

cassette, press the

o0cassette holder back

into position.

Press the PLAY button to begin playback.

“TAPE” appears on the display.

Press the STOP/ EJECT button to stop play-

back at any time. Press it again to remove the

cassette

TO TAPES

....,,.’.. ....,.

When the end of the tape has been reached,

the tape stops automatically.

Note:

-Use the normal tape (TYPE 1).

Endless tapes cannot be used.

Do not use C-100 (or longer) tapes.They may

jam in the mechanism.

Pause

Press the PAUSE button to temporarily stop play-

back or recording. Press it again to resume

operation.

Fast forward and rewind

Press the FFWD or REW button. When the de-

sired location has been reached, press the

STOP/EJECT button.

LISTENING TO THE RADIO

Before use

When the unit is shipped from the factory, its AM

frequency band is set as “522 -1611 kHz (in 9kHz

steps)”.

If your local AM broadcast system is organized in

10 kHz steps, change the frequency band to

“520-1 710 kHz (in 10 kHz steps)” as follows.

1. Set the function (lAPE/CD/RADIO) switch to

RADIO.

2. Press the BAND button to select “AM”.

3. Slide the function switch to CD.

4. While pressing the BAND button on the front

panel, slide the function switch to RADIO.

To return the original setting, repeat steps above.

Set the function switch to RADIO. The radio

frequency appears.

Select the desired radio band with the BAND

button.

Automatic tuning:

Press the TUNING UP or TUNING DOWN

button for at least 1second to tune in a

station.

Automatic /Manual tuning

-7-

,,. ,.,,, .,+,,,,,,, ,., ,:,, ,~~. !.(

The unit will scan up or down the band and

receive the next receivable station. Press the

button again to continue.

Manual tuning:

Press the TUNING UP or TUNING ,DOWN

button briefly until the desired frequency is

displayed.

4. To turn the radio off, set the function switch

to TAP130FF.

To receive FM stereo broadcasts

Make sure that “MONO” is not displayed. If

‘“MONO” appears, press the FM MODE button to

turn the “MONO” indication off.

“ST” appears when an FM stereo broadcast is re-

ceived.

-If the signal from an FM stereo station is weak

and reception is poor, press the FM MODE

button to change to the MONO mode. The re-

ception may be improved, but the sound will

be monaural.

To improve reception

FM: Pull out the telescopic aerial and adjust its

position.

AM: Rotate the unit.

To preset stations

Up to 20 FM and 12 AM stations can be preset.

Tune in the station to be preset as described

above.

Press the MEMORY button.

While “MEM” is blinking, press the PRESET

button to select the channel to be preset.

IMM Cti I

While “MEM” is blinking, press the MEMORY

button. “MEM” disappea&..

-In this example, “103.25 MHz” FM station

is preset on FM channel 9.

-The number buttons on the remote con-

trol can also be used. In this example,

press O, then 9after the step 2above.

5. Repeat steps above to add more preset

stations.

-When presetting anew station, the previ-

ous preset station is cleared.

Listening to preset stations

1. Select “RADIO” function and select the band.

2. Press the PRESET button briefly.

The number buttons on the remote con-

trol can also be used.

Preset scan tuning

1. Select “RADIO” function and select the band.

2. Press the PRESET button for at least 1

second. “PS” blinks on the display. Each of

the preset stations is tuned in for 5seconds.

3. When the desired station has been tuned in,

press the PRESET button again to keep the

reception locked at that station.

RECORDING

Recording copyright material without permission

of the copyright owners is usually an

infringement. If you wish to re-record copyright

material, permission from the copyright owner is

necessary. SANYO does not approve of, and

cannot be held responsible for, any unlawful use

of this machine.

Recording compact discs (Synchronous

recording)

1. Load ablank cassette.

2. Select “CD” function.

3. Load the disc to be recorded.

-Select the track number if required.

-For programmed recording, programme

the material in advance (as described un-

der “PROGRAMMED PLAY”).

4. Press the REC button. The PLAY button is

engaged simultaneously and CD recording

starts.

. ... .-—.-. ...—

-When you want to record music as you

listen, press the REC button. Recording

starts automatically from the beginning of

the track.

5. Press the STOP/EJECT button to stop

recording.

When the end of the tape is reached, the CD

player and deck stop automatically.

Recording from the radio

1. Load ablank cassette.

2. Tune in the radio station to be recorded.

3. Press the REC button to start recording.

4. Press the STOP/EJECT button to stop

recording.

When beat is heard

Beat (a high-pitched noise) may sometimes be

heard during the recording of radio broadcasts. If

this occurs, set the BEAT CANCEL switch to the

position that reduces the level of the beat noise.

‘.

!’.

,:,:

>,,

j’

;,;

.,.

‘4

,.. .

....

‘i

,,”.

:.’,

....

.’

..,.

.“!

,..<

.’,

,.}

., !

-8-

,..4;

.,. . {

,, ,’!

,,..,

,,.,

. .

,..,

.,,,

‘,’.

:., :

.: :

,,-

, ..

:.+“.

.: ..!

:,:

.,, .

,..’.

,.. .

,,’:

,,. .

,.. ,

:.:,

.- ...

.7. .

!,, ,

,., ,

,.,

,; .”,

:.“,,.

,.,

Safeguards against accidental erasure

To protect side A, break out tab (1). To protect

side B, break out tab (2).

-To erase or record aprotected cassette,

cover the tab openings with adhesive tape

(3).

Note:

The REC button cannot be depressed when us-

ing aprotected cassette.

MAINTENANCE . .....,,..-,,-.+.... -_ ... ..=

Cleaning the unit

Clean the outside of the unit with aclean soft

cloth, moistened with lukewarm water. Do not

use benzene, thinners, or alcohol since they will

mar the finish of the surfaces.

Cleaning the tape heads and tape path

To ensure continued high performance, use a

cleaning tape (available from your local audio

dealer) to clean the head block of the deck after

about every 10 hours of use.

Cleaning the CD player lens

The lens should never be touched. If dust is on

the lens, blow it off using acamera lens blower.

(Consult your dealer.)

+9=@

-9-

Andere Handbücher für MCD-Z330F

Inhaltsverzeichnis

Andere Sanyo Kassettenspieler Handbücher

Sanyo

Sanyo M9998 Bedienungsanleitung

Sanyo

Sanyo MCD-Z150F Bedienungsanleitung

Sanyo

Sanyo CWM-240 Bedienungsanleitung

Sanyo

Sanyo M-1075C Bedienungsanleitung

Sanyo

Sanyo MCD-Z18F Bedienungsanleitung

Sanyo

Sanyo M GP9 Bedienungsanleitung

Sanyo

Sanyo M7700L Bedienungsanleitung

Sanyo

Sanyo MCD-Z90F Bedienungsanleitung

Sanyo

Sanyo M-1060C Bedienungsanleitung

Sanyo

Sanyo MCD-ZX100F Bedienungsanleitung

Sanyo

Sanyo MCD-ZX200F Bedienungsanleitung

Sanyo

Sanyo MCD-Z16F Bedienungsanleitung

Sanyo

Sanyo MCD-Z31F Bedienungsanleitung

Sanyo

Sanyo MCD-X75L Bedienungsanleitung

Sanyo

Sanyo MCD-UB685M/AU-2 Bedienungsanleitung

Sanyo

Sanyo TRC-2050C Bedienungsanleitung

Sanyo

Sanyo MCD-XJ780A Bedienungsanleitung

Sanyo

Sanyo MCD-Z22L Bedienungsanleitung

Sanyo

Sanyo MCD-Z12F Bedienungsanleitung

Sanyo

Sanyo ES-P7 Bedienungsanleitung

Sanyo

Sanyo TRC-960C Bedienungsanleitung

Sanyo

Sanyo MCD-Z110F Bedienungsanleitung

Sanyo

Sanyo M9930K Bedienungsanleitung

Sanyo

Sanyo MG-3 Bedienungsanleitung

Beliebte Kassettenspieler Handbücher anderer Marken

Aiwa

Aiwa TP-VS535 Bedienungsanleitung

Philips

Philips AW 7300 Bedienungsanleitung

Philips

Philips Video Cassette Recorder Bedienungsanleitung

Yamaha

Yamaha MT8X Bedienungsanleitung

Sherwood

Sherwood Newcastle D-480 Bedienungsanleitung

Manta

Manta MA408 Bedienungsanleitung

GPO

GPO W0162B Bedienungsanleitung

Sony

Sony HST-471 Bedienungsanleitung

Sharp

Sharp JC-AV1 Bedienungsanleitung

Pioneer

Pioneer CT-W103 Bedienungsanleitung

Aiwa

Aiwa HS-JX899 Bedienungsanleitung

Sony

Sony TC-K615S Bedienungsanleitung

Sony

Sony CFS-B15 - Am/fm Stereo Cassette Recorder Bedienungsanleitung

Sony

Sony WMFS220 - Portable Sports AM/FM Cassette... Bedienungsanleitung

Aiwa

Aiwa HS-TA21 Bedienungsanleitung

Aiwa

Aiwa CS-P77 Bedienungsanleitung

Sony

Sony Pressman TCM-465V Bedienungsanleitung

Sony

Sony WALKMAN WM-GX808 Bedienungsanleitung