Sanyo PLC-WXU30 Bedienungsanleitung

Memory Viewer function

This is the manual for the Memory Viewer function.

Read this manual thoroughly to operate the Memory Viewer function.

First, read the owner's manual of the projector to understand the basic operation of the

projector and the safety instructions.

The safety instructions in the owner's manuals should be followed strictly.

Owner's Manual

Memory viewer function

Memory Viewer function

The Memory Viewer function is to make a presentation or project an image without using computers

or some other external equipment. You do not have to carry a computer or other equipment to project

images.

Store images on a dedicated SD memory card and insert it into the SD memory card slot of the

projector, then you can project those images.

This projector is also equipped with dedicated Network Viewer 4 software to edit the presentation

images to project with the Memory Viewer function. With this function, you can edit images, photo

data, or Power Point data into a more effective presentation data. For further information of the

Network Viewer software, see the chapter "9. Network viewer function" on the separated booklet of

"Network Owner's manual".

Which images can be projected with the Memory Viewer function?

With the Memory Viewer function, you can project images in these formats below.

• Bitmap data

• JPEG data converted with the Network Viewer 4 [File Converter 1 and 2] software.

• Text data

• Program file created with the Network Viewer 4 [Program Editor].

*Some data may not be projected even with these formats.

Text data used with Memory Viewer

Memory viewer supports the text file with the ASCII format for single byte. Other text formats cannot

be supported.

Back up the data

It is recommended that important data to edit with Network Viewer and store in SD memory card

should be stored in other media in advance. We are not responsible for any data losses or damages

resulting from use of the Memory Viewer function.

Trademarks

Microsoft, Windows, and PowerPoint are either registered trademarks or trademarks of Microsoft

Corporation in the United States and/or other countries. Each name of corporation or product in this

owner's manual is either a registered trademark or a trademark of its respective corporation.

• The On-Screen Menu and figures in this manual may differ slightly from the product.

• The contents of this manual are subject to change without notice.

LOCK

Top Bottom

Lock

Memory card for the Memory Viewer function

The memory card is not provided with this projector. The types of memory card which can be used

with the Memory Viewer function of this projector is "SD Memory Card". It may not be used with this

projector depending on the type of the SD memory card. A new SD memory card or a card formatted

by computer or camera must be formatted by this projector. The Memory Viewer function may not

operate properly with a card formatted by other equipment.

SD memory card slot

SD memory card indicator

SD memory card slot

The projector provides an SD memory card slot on the back side. The SD memory card indicator lights

up when the SD memory card is inserted rightly.

Shape of SD memory card

Capacity of SD Memory Card: up to 8GB

* There may not be used with this projector depending

on the type or manufacturer of the SD memory card.

Memory viewer function

Note:

✐During accessing to the SD memory card, do not turn off the power or eject the card because the

data in the card might get damaged. During accessing, the SD memory card indicator is blinking

✐The SD memory card allows you to insert or remove regardless of the power status of the projector.

Removing the SD memory card

Push the SD memory card in the arrow direction gently to remove. The card comes out and you can

remove it.

Push the card until

it clicks. The card

comes out.

Inserting the SD memory card

Insert the SD memory card into the card slot on the back side of the projector as shown in the figure

below.

Insert a card with

cutting side up until

it clicks.

Entering the memory viewer mode

1. Select “Wired” or "Wireless" from the input menu of the projector. The “Please wait...” message will be

displayed on the screen. After short time, the network connection standby display screen "Ready for

use" will appear.

2. Insert the SD memory card into the card slot on the back side of the projector. The card indicator

lights up.

3. Select “Wired setting” or "Wireless setting" in the projector menu, and press SELECT button.

4. Select "Memory Viewer" with the point ed button and press SELECT button. The "Enter/Exit" pallet

of the memory viewer appears.

5. Select "Enter" and press SELECT button. The memory viewer start-up image appears briefly and an

image stored in the SD memory card is displayed on the screen.

* If the image file is not available in the root directory of the SD memory card, the memory viewer

browser window appears.

Memory viewer

Wireless setting

Wired setting

Memory viewer function

Displaying the memory viewer browser window

When you press AUTO SETUP/CANCEL button in the memory viewer mode, following browser window

"Thumbnail" or "Filename list" appears on the screen.

Filename list display

Displays current directory path

Moves

to upper

directory

Thumbnail display Displays current directory path

* When you set up the custom screen size with the screen setting of the projector, a part of the browser

window of the memory viewer may get cut off from the custom screen size. In that case, readjust the

custom screen size.

Menu tree

Menu Sub menu Description

Menu Manual mode Mode to select a playing file respectively

Available file types are JPEG(.jpg), Bitmap(.bmp), Text(.txt). Others are not

available.

Program mode Mode to select a program file (.dpf) created by the program editor.

Format Formats the SD memory card

Display Thumbnail Displays files with the thumbnail on the browser window.

Filename list Displays files with the file name on the browser window.

Set English < > Selects display menu language, Japanese or English. Set with 7 8 button

3 sec. < > Sets display period of an image in the auto display mode. (3 to 240

seconds) Set with point 7 8 button.

0 times < > Sets the repeating times in the auto display mode. (0 to 255 times). 0

means endless play. Set with point 7 8 button.

Exit Quits the Memory Viewer operation.

Icon indication

Folder icon. Displays the contents of the selected folder with SELECT button

Top directory icon. Moves to upper directory with SELECT button

JPEG file icon

Bitmap file icon

Text file icon

Program file icon (Playback with the program mode)

Un-supported file icon

Note:

* The memory viewer does not support the resolution of image more than the panel resolution of the

projector.

* Text file can be displayed up to 15,000 rows with 110 characters per row.

Selection of memu

1. To select the menu, press AUTO SETUP/CANCEL button in the memory viewer mode. The cursor

moves from file selection window to menu.

2. Select the sub-menu with point buttons and press SELECT button. To cancel the selection, press

AUTO SETUP/CANCEL button.

Memory viewer function

Image viewer in the manual mode

1. Select "Manual mode" from "Menu" on the browser window of the memory viewer and press SELECT

button.

2. Select a file to display with point buttons and press SELECT button. The selected file image is

displayed on the screen.

3. During displaying the image, you can control the displayed image with control buttons as described

in the table below.

* The display time of the image and the number of repeat at the auto-playback mode are set up

from the "Set" menu on the browser window.

* Point 78buttons operate as the scroll key during displaying the text file .

Note:

During operating the memory viewer, the Network Viewer and Network Capture function cannot be used.

The program file does not support in the manual mode. Use it in the program mode.

Point Operation

dManual playback with next file

eManual playback with previous file

8Start auto-playback*

7 Stop auto-playback*

* To display the portrait documents such as text files, use the point 7 8 buttons to scroll up and down the page.

Image viewer in the program mode

1. Select "Program" on "Menu" of the browser window of the memory viewer. And press SELECT button.

The program files (.dpf) in the DispParam folder under the top directory are displayed.

* If the DispParam folder is not placed in the top directory, the list of the folder name is displayed. Find

the DispParam folder which stores the program file manually to display the contents of the folder.

2. Select a program file with point buttons and press SELECT button. The dialogue window appears

and select "Yes" and press SELECT button to start the auto display. The images programmed by

program file are displayed on the screen. The display period of the image and the number of repeat

are set with the program file.

3. During displaying the image, you can control the displayed image with control buttons as described

in the table below.

* The program file (.dpf) is created with the program editor software. For further information, see the

item "Creating the program file [Program Editor]" (p.115) described on the separated booklet of

network owner's manual.

* The DispParam folder is automatically created when the program file with the program editor is

stored. For further information, see the item "Creating the program file [Program Editor]" (p.115)

described on the separated booklet of network owner's manual.

* When storing the program file into the SD memory card manually, create folder with the name of

"DispParam" and store the program file into this folder.

* In the program mode, the browser window lists the program files and folders only. Other files are

not listed.

Point Operation

dManual playback with next file

eManual playback with previous file

8Start auto-playback

7 Stop auto-playback

Termination of memory viewer

To terminate the memory viewer function, take one of methods described below.

- Terminate with projector's on-screen menu.

1. Select “Wired” or "Wireless" from the input menu of the projector. Press SELECT button.

2. Select "Memory Viewer" with the point ed buttons and press SELECT button. The "Enter/Exit" pallet

of the memory viewer appears.

3. Select "Exit" and press the SELECT button.

- Terminate with memory viewer mode

1. During the image displaying, press AUTO SETUP/CANCEL button. The browser window appears on

the screen.

2. Press AUTO SETUP/CANCEL button again. The cursor moves to menu item.

3. Select "Exit" on the browser window with the point 78 buttons and press SELECT button.

While operating the memory viewer, the Network Viewer and Network Capture function cannot be used.

Memory viewer function

Duplicating the data into the SD memory card

It is described how to duplicate the data converted with the Network Viewer 4 [File Converter 1, File

Converter 2] into the SD memory card through the network.

1. Launch the explorer software of the computer and type the IP address of the network board which

has the SD memory card onto the address column. For example, "ftp://192.168.1.201".

The contents of the SD memory card appear on the explorer window as below.

2. Move the projection data from the computer into the SD memory card.

Note:

If the network PIN code is set for the projector, the authentication window appears as below. In that

case, enter "user" into the User Name column and the network PIN code of the projector into the

Password column. *User Name must be "user".

Andere Handbücher für PLC-WXU30

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sanyo Projektor Handbücher

Sanyo

Sanyo PLC-ZM5000L - 5000 Lumens Bedienungsanleitung

Sanyo

Sanyo PLC-XF47K Bedienungsanleitung

Sanyo

Sanyo PLC-XM150L Bedienungsanleitung

Sanyo

Sanyo PLC-XU106 Installationshandbuch

Sanyo

Sanyo PLC-XU45 Bedienungsanleitung

Sanyo

Sanyo PLC-SU22N Bedienungsanleitung

Sanyo

Sanyo PDG-DSU30 - 2500 Stücklistenhandbuch

Sanyo

Sanyo PLC-WK2500 - 2500 Lumens Bedienungsanleitung

Sanyo

Sanyo PLC-750M Bedienungsanleitung

Sanyo

Sanyo PLC-XF10NZ Bedienungsanleitung

Sanyo

Sanyo PLC-XW20 Bedienungsanleitung

Sanyo

Sanyo PLC-XF30 Bedienungsanleitung

Sanyo

Sanyo PLC-XU300A - 3000 Lumens Bedienungsanleitung

Sanyo

Sanyo PLC-XR201 Bedienungsanleitung

Sanyo

Sanyo PLC-XP21N Bedienungsanleitung

Sanyo

Sanyo PLC-XP07N Bedienungsanleitung

Sanyo

Sanyo PLC-XW60 Bedienungsanleitung

Sanyo

Sanyo PDG-DSU21N - SVGA DLP Projector Bedienungsanleitung

Sanyo

Sanyo PLC-XT35L Bedienungsanleitung

Sanyo

Sanyo PLC-WL2503 Bedienungsanleitung

Sanyo

Sanyo PLC-XM100 Bedienungsanleitung

Sanyo

Sanyo PLC-XD2200 Produktinformationsblatt

Sanyo

Sanyo LNS LNS-W03 Gebrauchs- und Pflegehandbuch

Sanyo

Sanyo PLC-WL2500 - 2500 Lumens Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung