Sanyo MPR-1411 Bedienungsanleitung

- 38 -- 38 -

MPR-1411

MPR-1411R

Pharmaceutical Refrigerator

INSTRUCTION MANUAL

MPR-1411R

- 39 -- 39 -

CONTENTS

INTRODUCTION P.2

PRECAUTIONS FOR SAFE OPERATION P. 3

ENVIRONMENTAL CONDITIONS P. 7

REFRIGERATOR COMPONENTS P. 8

Control panel P. 10

Inside of front cover P. 11

INSTALLATION SITE P. 12

INSTALLATION P. 13

START-UP OF UNIT P. 14

STOCK OF CONTAINERS P. 15

CHAMBER TEMPERATURE SETTING P. 16

ALARM TEMPERATURE SETTING P. 17

SETTING OF DELAY OF DOOR ALARM P. 18

SETTING OF ALARM RESUME TIME P. 19

KEY LOCK FUNCTION P. 20

DEFROST CYCLES P. 21

REMOTE ALARM TERMINAL P. 21

ALARMS & SAFETY FUNCTIONS P. 22

ROUTINE MAINTENANCE

Cleaning of cabinet P. 23

Cleaning of evaporating tray P. 23

Replacement of fluorescent lamp P. 24

Replacement of glow starter P. 25

Cleaning of condenser filter P. 25

TROUBLESHOOTING P. 26

DISPOSAL OF UNIT P. 27

OPTIONAL COMPONENTS

Automatic temperature recorder P. 32

Attachment of recorder MTR-0621LH P. 32

Attachment of recorder MTR-G04A P. 33

Attachment of battery kit MPR-48B P. 35

Setting for battery before starting P. 37

SPECIFICATIONS P. 38

PERFORMANCE P. 38

SAFETY CHECK SHEET P. 39

- 40 -- 40 - 2

INTRODUCTION

ŶRead this manual carefully before using the appliance and follow the instructions for safety operation.

ŶSanyo never guarantee any safety if the appliance is used for any objects other than intended use or

used by any procedures other than those mentioned in this manual.

ŶKeep this manual in an adequate place to refer to it as necessary.

ŶThe contents of the manual will be subjected to change without notice due to the improvement of

performance or functions.

ŶContact Sanyo sales representative or agent if any page of the manual is lost or page order is incorrect.

ŶContact Sanyo sales representative or agent if any point in this manual is unclear or if there are any

inaccuracies.

ŶNo part of this manual may be reproduced in any form without the expressed written permission of

Sanyo.

CAUTION

SANYO guarantees the product under certain warranty conditions. SANYO in no way shall be

responsible for any loss of content or damage of content.

- 41 -- 41 -

PRECAUTIONS FOR SAFE OPERATION

It is imperative that the user complies with this manual as it contains

important safety advice.

Items and procedures are described so that you can use this unit correctly and safely.

If the precautions advised are followed, this will prevent possible injury to the user and

any other person.

Precautions are illustrated in the following way:

WARNING

Failure to observe WARNING signs could result in a hazard to personnel

possibly resulting in serious injury or death.

CAUTION

Failure to observe CAUTION signs could result in injury to personnel and

damage to the unit and associated property.

Symbol shows;

this symbol means caution.

this symbol means an action is prohibited.

this symbol means an instruction must be followed.

Be sure to keep this manual in a place accessible to users of this unit.

< Label on the unit >

This mark is labeled on the cover in which the electrical components of high voltage

are enclosed to prevent the electric shock.

The cover should be removed by a qualified engineer or a service personnel only.

- 42 -- 42 - 4

PRECAUTIONS FOR SAFE OPERATION

Do not use the unit outdoors. Current leakage or electric shock may result if the unit is exposed to

rain water.

Only qualified engineers or service personnel should install the unit. The installation by

unqualified personnel may cause electric shock or fire.

Install the unit on a sturdy floor and take an adequate precaution to prevent the unit from

turning over. If the floor is not strong enough or the installation site is not adequate, this may result

in injury from the unit falling or tipping over.

Never install the unit in a humid place or a place where it is likely to be splashed by water.

Deterioration of the insulation may result which could cause current leakage or electric shock.

Never install the unit in a flammable or volatile location. This may cause explosion or fire.

Never install the unit where acid or corrosive gases are present as current leakage or electric

shock may result due to corrosion.

Always ground (earth) the unit to prevent electric shock. If the power supply outlet is not

grounded, it will be necessary to install a ground by qualified engineers.

Never ground the unit through a gas pipe, water main, telephone line or lightning rod. Such

grounding may cause electric shock in the case of an incomplete circuit.

Connect the unit to a power source as indicated on the rating label attached to the unit. Use

of any other voltage or frequency other than that on the rating label may cause fire or electric shock.

Never store volatile or flammable substances in this unit if the container cannot be sealed. These

may cause explosion or fire.

Do not insert metal objects such as a pin or a wire into any vent, gap or any outlet on the unit.

This may cause electric shock or injury by accidental contact with moving parts.

Use this unit in safe area when treating the poison, harmful or radiate articles. Improper use

may cause bad effect on your health or environment.

Turn off the power switch (if provided) and disconnect the power supply to the unit prior to any

repair or maintenance of the unit in order to prevent electric shock or injury.

Do not touch any electrical parts (such as power supply plug) or operate switches with a wet

hand. This may cause electric shock.

WARNING

- 43 -- 43 -

PRECAUTIONS FOR SAFE OPERATION

Ensure you do not inhale or consume medication or aerosols from around the unit at the time of

maintenance. These may be harmful to your health.

Never splash water directly onto the unit as this may cause electric shock or short circuit.

Never put containers with liquid on the unit as this may cause electric shock or short circuit when

the liquid is spilled.

Never bind, process, or step on the power supply cord, or never damage or break the power

supply plug. A broken supply cord or plug may cause fire or electric shock.

Do not use the supply cord if its plug is loose. Such supply cord may cause fire or electric shock.

Never disassemble, repair, or modify the unit yourself. Any such work carried out by an

unauthorized person may result in fire, or electric shock or injury due to a malfunction.

Disconnect the power supply plug if there is something wrong with the unit. Continued

abnormal operation may cause electric shock or fire.

When removing the plug from the power supply outlet, grip the power supply plug, not the cord.

Pulling the cord may result in electric shock or fire by short circuit.

Disconnect the power supply plug before moving the unit. Take care not to damage the power

cord. A damaged cord may cause electric shock or fire.

Disconnect the power plug when the unit is not used for long periods. Keeping the connection

may cause electric shock, current leakage, or fire due to the deterioration of insulation.

If the unit is to be stored unused in an unsupervised area for an extended period, ensure that

children do not have access and that doors cannot be closed completely.

The disposal of the unit should be accomplished by appropriate personnel. Remove doors to

prevent accidents such as suffocation.

Do not put the packing plastic bag within reach of children as suffocation may result.

WARNING

- 44 -- 44 - 6

PRECAUTIONS FOR SAFE OPERATION

Use a dedicated power source (a dedicated circuit with a breaker) as indicated on the rating label

attached to the unit. A branched circuit may cause fire resulting from abnormal heating.

Connect the power supply plug to the power source firmly after removing the dust on the plug.

A dusty plug or improper insertion may cause a heat or ignition.

Never store corrosive substances such as acid or alkali in this unit if the container cannot be

sealed. These may cause corrosion of inner components or electric parts.

Check the setting when starting up of operation after power failure or turning off of power

switch. The stored items may be damaged due to the change of setting.

Be careful not to tip over the unit during movement to prevent damage or injury.

Prepare a safety check sheet when you request any repair or maintenance for the safety of service

personnel.

CAUTION

- 45 -- 45 -

ENVIRONMENTAL CONDITIONS

This equipment is designed to be safe at least under the following conditions (based on the IEC 61010-1):

1. Indoor use;

2. Altitude up to 2000 m;

3. Ambient temperature 5oC to 40oC

4. Maximum relative humidity 80% for temperature up to 31oC decreasing linearly to 50% relative

humidity at 40oC;

5. Mains supply voltage fluctuations not to exceed ±10% of the nominal voltage;

6. Other supply voltage fluctuations as stated by the manufacture;

7. Transient overvoltages according to Installation Categories (Overvoltage Categories) II; For mains

supply the minimum and normal category is II;

8. Pollution degree 2 in accordance with IEC 60664.

- 46 - 8

REFRIGERATOR COMPONENTS

11 10

MPR-1411R

MPR-1411

Rear side

- 47 -

REFRIGERATOR COMPONENTS

1. Front cover: A front cover opens when a bottom part is pulled to the front. Open this cover when you

use cleaning of the condenser filter, a remote alarm terminal. Refer to page 11.

2. Control panel: Panel opens when the right top of the lower part cover is pushed. Refer to page 10.

3. Light switch: This switch is used for turning the fluorescent lamp off and on.

4. Space for temperature recorder: An temperature recorder (optional accessory) can be mounted here.

See page 32.

5. Fluorescent lamp: 40 W white lamp. See page 24 for replacement.

6. Lock: Turn the key clockwise through 180oto securely lock the door.

7. Glass window: The window may have condensation in high humidity environment. Wipe off the

condensation with a soft dry cloth.

8. Handle: Always hold the handle when opening/closing the door.

9. Dew receiver: The condensation on the outer door is accumulated on this dew receiver. Wipe off the

water on the dew receiver with a cloth.

10. Leveling foot: Adjust the height of the leveling feet by turning the screw bolts until the unit is level.

11. Caster: When installing the unit, the castors can be raised from the floor by using the leveling feet

above.

12. Drawer (MPR-1411R only): Items to be stored in the chamber must be placed on the drawers.

The maximum storage weight for each drawer is 40 kg.

Shelf (MPR-1411 only): Items to be stored in the chamber must be placed on the shelves. The

maximum storage weight for each shelf is 50 kg. Do not put stored items directly onto the interior floor of

the chamber. See page 15.

13. Access port: This port allows temperature measurement cables to enter the chamber from outside.

A total of three (3) ports are provided; left side, right side and top.

14. Exhaust air vent: Do not block this vent. If this vent is blocked, temperature regulation will become

unstable. Do not place stored items in the path of the cold air.

15. Intake air vent: Do not block this vent. If this vent is blocked, temperature regulation will become

unstable. Do not insert a finger or any foreign object into this vent as there is danger from the internal fan.

16. Door switch: When a door opens, a fan for the cold circulation is stopped, and the leakage of the

cold is prevented. And, the check lamp of the door is turned on.

17. Fixture: 2 fixtures are attached on the rear side of the unit. These keep adequate space between

the unit and wall and also can be used for fixing the unit. See page 13.

18. Evaporating tray: Defrost water from the evaporator accumulates on the tray and evaporates into

the atmosphere. See page 23 for cleaning.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sanyo Kühlschrank Handbücher

Sanyo

Sanyo MPR-721 Bedienungsanleitung

Sanyo

Sanyo MPR-1014 Bedienungsanleitung

Sanyo

Sanyo SRR-23GD-MED - Commercial Solutions Lab Bedienungsanleitung

Sanyo

Sanyo MBR-1404G Bedienungsanleitung

Sanyo

Sanyo SR4433S - Refridgerator 4.4 Cu FTF Bedienungsanleitung

Sanyo

Sanyo SR-3770S Bedienungsanleitung

Sanyo

Sanyo SR-S701TW Bedienungsanleitung

Sanyo

Sanyo SR-3720M - Counter-High Refrigerator Bedienungsanleitung

Sanyo

Sanyo SR-6100K Bedienungsanleitung

Sanyo

Sanyo SR-2410K Leitfaden

Sanyo

Sanyo MPR-414F - Commercial Solutions Refrigerator Leitfaden

Sanyo

Sanyo SR-257 Bedienungsanleitung

Sanyo

Sanyo SR-3620W Bedienungsanleitung

Sanyo

Sanyo Validation Bedienungsanleitung

Sanyo

Sanyo SR-2570M Bedienungsanleitung

Sanyo

Sanyo MPR-311D(H) Bedienungsanleitung

Sanyo

Sanyo SR-368W/K - Counter-High Refrigerator With Timer Auto... Montageanleitung

Sanyo

Sanyo MPR-311D(H) Bedienungsanleitung

Sanyo

Sanyo SR-2570M - 2.5 cu. Ft. Mid-Size Refrigerator Bedienungsanleitung

Sanyo

Sanyo SR-S52TW Bedienungsanleitung

Sanyo

Sanyo MPR-414FS Bedienungsanleitung

Sanyo

Sanyo SR-6100K Betriebsanleitung

Sanyo

Sanyo SR-1730 Bedienungsanleitung

Sanyo

Sanyo SRR-23FD-MED Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung