Sanyo VCB-3424 Bedienungsanleitung

INSTRUCTION MANUAL VCB-3424

B/W CCD Camera

About this manual

Before installing and using the camera, please read this manual

carefully. Be sure to keep it handy for later reference.

L73T4/US GB 1999, 8, 3

SANYO INDUSTRIAL VIDEO

B/W VIDEO CAMERA LIMITED WARRANTY

OBLIGATIONS

In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and

addresses of Authorized Sanyo Service Centers may be obtained by writing to SFS Corporation, SFC’s warranty administrator, at any of the addresses listed below, or by calling (toll-free) 1-800-421-5013.

New Jersey Office

210 Riser Road

Little Ferry, NJ 07643

201-641-3000

California Office

1200 W. Artesia Blvd.

Compton, CA 90220

310-537-5830

Illinois Office

900 N. Arlington Heights Rd.

Itasca, IL 60143

708-775-1414

THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING HAWAII AND ALL U.S. TERRITORIES AND PROTECTORATES. THIS

WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER

AT THE TIME WARRANTY SERVICE IS REQUESTED.

Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO FISHER (USA) CORPORATION warrants this SANYO product against defects in materials and workmanship for the periods specified below. SFC

will repair or replace (at its option) the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail.

LABOR PARTS IMAGE DEVICE

3 YEARS 3 YEARS 3 YEARS

EXCLUSIONS

This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model’s instruction manual, or (B) the repair of any product whose serial number has been altered, defaced

or removed.

This warranty shall not apply to the cabinet or cosmetic parts, antenna, knobs, batteries or image burns to projection or picture tubes caused by electronic devices or games.

This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.

This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized

service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire,

flood or other Acts of God, or normal wear and tear.

The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability.

THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS) IS LIMITED TO THE TERM OF THIS WARRANTY. IN NO EVENT

SHALL SFC BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS

UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.

ATTENTION

For your protection in the event of theft or loss of this product, please fill in the information below for you own personal records.

Model No._____________________________________________________________________ Serial No. _____________________________________________________________________

(Located on back or bottom side of unit.)

Date of Purchase _______________________________________________________________ Purchase Price _________________________________________________________________

Where Purchased _________________________________________________________________________________________________________________________________________________

L73T4/US GB 1999, 8, 3

14 English

Depending on the conditions of use, installation and environment,

please be sure to make the appropriate settings and adjustments. If

you need help with installation and/or settings, please consult your

dealer.

CONTENTS

INFORMATION TO USER .................................................................... 2

PRECAUTIONS..................................................................................... 3

PARTS NAMES..................................................................................... 4

MOUNTING THE LENS........................................................................ 7

CONNECTIONS.................................................................................... 9

SETTINGS............................................................................................. 10

TROUBLESHOOTING........................................................................... 12

SPECIFICATIONS.................................................................................. 13

ACCESSORIES

1C mount adaptor 5 mm).....................1 pc.

The C mount adaptor must be used to be able to install a C mount

lens on the camera.

2Lens iris plug 4-pin).............................1 pc.

FEATURES

•Built-in interline transfer method 1/3" CCD, approx. 270,000

picture elements

•Low smear, anti-blooming, low lag, no burning and no geometric

distortion using the CCD solid state image device.

•100% solid state components giving excellent immunity to shock

and vibration

•Not subject to interference from magnetic or electrostatic fields

•High sensitivity, minimum required illumination of 0,07 lux with

F1.2 lens

•Horizontal resolution, more than 400 TV lines

•New backlight compensation function Active when using an

auto-iris lens)

•Externally adjustable flange back mechanical focus)

•Low power consumption and quick start

•24 V AC operation

Commarcially available 24 V AC adaptor)

•Built-in Mirror image effect function.

L73T4/US GB 1999, 8, 3

English 1

Safety Guard

THIS SYMBOL INDICATES THAT THERE ARE

IMPORTANT OPERATING AND MAINTENANCE

INSTRUCTIONS IN THE LITERATURE ACCOMPANYING

THIS UNIT

WARNING:

TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE

This installation should be made by a qualified service person and

should conform to all local codes.

INFORMATION TO USER

For the customers in Canada

This Class B digital apparatus complies with Canadian ICES-003.

Pour la clientèle canadienne

Cet appareil numerique de la Classe B est conforme a la norme

NMB-003 du Canada.

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: 1) This device may not

cause harmful interference, and 2) this device must accept any

interference received, including interference that may cause

undesired operation.

Changes or modifications not expressly approved by Sanyo may

void the user’s authority to operate this camera.

L73T4/US GB 1999, 8, 3

2 English

PRECAUTIONS

In case of problem

Do not use the camera if smoke or a strange odour comes from the

unit, or if it seems not to function correctly. Disconnect the power

cord immediately, and consult your dealer or a Sanyo Authorized

Service Centre).

Do not open or modify

Do not open the cabinet, as it may be dangerous and cause damage

to the unit. For internal settings and repairs, consult your dealer or a

Sanyo Authorized Service Centre).

Do not put objects inside the unit

Make sure that no metal objects or flammable substance get inside

the camera. If used with a foreign object inside, it could cause a fire,

short-circuits or damages.

If water or a liquid gets inside the camera, disconnect the power cord

immediately, and consult your dealer or a Sanyo Authorized Service

Centre). Be careful to protect the camera from rain, sea water, etc.

Be careful when handling the unit

To prevent damages, do not drop the camera or subject it to strong

shock or vibration.

Install away from electric or magnetic fields

If installed close to a TV, radio transmitter, magnet, electric motor,

transformer, audio speakers the magnetic field they generate will

distort the image.

Protect from humidity and dust

To prevent damages to the camera, do not install it where there is

greasy smoke or steam, where the dampness may get too high, or

where there is a lot of dust.

Protect from high temperatures

Do not install close to stoves, or other heat generating devices, such

as spotlights, etc., or where it could be subject to direct sunlight, as

that could cause deformation, discoloration or other damages.

Be careful when installing close to the ceiling, in a kitchen or boiler

room, as the temperature may raise to high levels.

Install where the temperature range will stay between –10˚C and 50˚C.

no condensation)

Cleaning

•Dirt can be removed from the cabinet by wiping it with a soft

cloth. To remove stains, wipe with a soft cloth moistened with a

soft detergent solution and wrung dry, then wipe dry with dry soft

cloth.

•Do not use benzine, thinner or other chemical product on the

cabinet, as that may cause deformation and paint peeling. Before

using a chemical cloth, make sure to read all accompanying

instructions. Make sure that no plastic or rubber material comes in

contact with the cabinet for a long period of time, as that may

cause damage or paint peeling.

L73T4/US GB 1999, 8, 3

English 3

PARTS NAMES

1Video output connector (VIDEO OUT: BNC type)

Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.

2Line phase adjustment volume (LINE PHASE)

When using two cameras or more, the image on the monitor may roll vertically when switching sources. This

rolling can be minimized by turning this volume.

3Power indicator (POWER)

Comes on when the power to the camera is on.

424 V AC input terminal (24 V AC, GND)

Connect to 24 V AC UL listed class 2 power supply.

5Camera setup section (under the cover)

These settings are for when using a 1/3 inch CS mount DC without EE internal amplifier) type lens. However,

if due to installation conditions or environment the settings may need to be modified for best results see

"SETTINGS").

To access the controls, loosen the cover fixing screw A, then remove the cover

6Lens iris output connector (LENS)

This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens.

L73T4/US GB 1999, 8, 3

4 English

PARTS NAMES

7Lens mount cap

The cap is installed to protect the lens mount section.

Remove the lens mount cap before installing a lens sold separately).

8Flange-back adjustment screw (FLANGE BACK ADJ )

9Flange-back lock screw (FLANGE BACK LOCK)

FCamera installation bracket

The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the

longer screws and install the shorter screws on the opposite side to seal the openings.

1Shorter screws: M3 x 4

2Longer screws: M3 x 6

3Camera mounting screw hole: 1/4"-20 UNC

CAUTION:

When installing the camera support, select a location that can support the total weight of the

camera and accessories

1232

L73T4/US GB 1999, 8, 3

English 5

PARTS NAMES

Concerning auto-iris lenses

DC type auto-iris lens

A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is

referred to as DC type coil lens or DC type non-amplifier lens.

Set the A I LENS switch to the DC position.)

VIDEO type auto-iris lens

A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is

referred to as EE amplifier type lens.

ALC and LEVEL volume level controls are available on the lens for iris adjustments.

Set the A I LENS switch to the VIDEO position.)

Compatible auto-iris lenses

1/3 inch Sanyo DC type lens VIDEO type lens

VCL-CS8LY: Standard angle, f= 8 mm Standard angle, f= 9 mm

VCL-CS4LY: Wide angle, f= 4 mm Telephoto angle, f= 12 mm

VCL-CS2LY: Ultra-wide angle, f= 2.8 mm More telephoto angle, f= 16 mm

If using a VIDEO type auto-iris lens

•Set the ALC and LEVEL controls on the lens to adjust the iris. Normally the ALC volume should be turned

all the way to Av Average).

•Depending on the type of lens used, the lens may not perform properly. In such a case, adjust the LEVEL

volume on the lens casing to correct.

VIDEO

A. I.

LENS

L73T4/US GB 1999, 8, 3

6 English

MOUNTING THE LENS

Please use a DC type auto-iris lens (sold separately)

Checking the lens mount

Do not use a lens if length “L” is more than 7 mm. If not, that may damage the camera and prevent

proper installation.

1Remove the lens mount cap from the camera

2Install the auto-iris lens

CS mount type lens

Carefully align the lens mount with the camera opening, then turn the lens slowly to install it.

C mount type lens

To allow for flange-back adjustment, install the supplied C-mount adaptor on the lens mount, then

carefully align the lens mount with the camera opening and turn the lens slowly to install it.

3Connect the lens plug to the lens iris output connector (LENS) on the side of the camera

When using lenses from other makers, the plug shape may not correspond to the terminal on the camera.

In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug

according to the diagram. Refer to page 8.)

C mount type lens

CS mount type lens

L73T4/US GB 1999, 8, 3

English 7

MOUNTING THE LENS

Rewiring the lens cable in the lens iris plug

1Prepare the lens cable

Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire.

2Install the lens iris plug

Solder the cable to the pins following the correct pin layout refer to the table and illustrations), then close

the plug cover.

Pin layout

DC type lenses VIDEO type lenses

1Brake coil –) +12 V DC 50 mA max.)

2Brake coil +) Not used

3Drive coil +) Video output 1.0 Vp-p, high impedance)

4Drive coil –) Ground for video signal and DC power)

Flange-back adjustment

If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of

focus in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the

flange-back position as described below.

1Using a + screwdriver, loosen the FLANGE BACK LOCK screw M2:+).

Set the zoom lens to the maximum telephoto position, set the focus using the focus ring on the lens.

2Set the zoom lens to the maximum wide angle position, set the focus using the FLANGE BACK ADJ screw.

3Repeat steps 2 and 3, until the image stays in focus when changing from a telephoto shot to a wide angle shot.

When the setting is complete, tighten the FLANGE BACK LOCK screw.

LOCK

ADJ.

L73T4/US GB 1999, 8, 3

8 English

Andere Handbücher für VCB-3424

Inhaltsverzeichnis

Andere Sanyo Sicherheitskamera Handbücher

Sanyo

Sanyo VCB-3372 Bedienungsanleitung

Sanyo

Sanyo VCC-6594 Bedienungsanleitung

Sanyo

Sanyo VCB-3374 Bedienungsanleitung

Sanyo

Sanyo Colour CCD Camera VCC-5775P Bedienungsanleitung

Sanyo

Sanyo VCC-P9574S - 1/4" CCD Pan-Focus PTZ Dome... Bedienungsanleitung

Sanyo

Sanyo VCC-9684VA - 1/4" Color CCD Indoor Mini Dome... Bedienungsanleitung

Sanyo

Sanyo VCB-3384 Bedienungsanleitung

Sanyo

Sanyo DSR-HB8000 Bedienungsanleitung

Sanyo

Sanyo VCC-6584E - 1/3" Color CCD DSP High-Resolution... Bedienungsanleitung

Sanyo

Sanyo VCC-HD4600 - Full HD 1080p Day/Night Network... Bedienungsanleitung

Sanyo

Sanyo VCC-3924P Bedienungsanleitung

Sanyo

Sanyo VCC-4794E - 1/3" Color CCD DSP Day/Night... Bedienungsanleitung

Sanyo

Sanyo VCB-7312P Bedienungsanleitung

Sanyo

Sanyo VCB-3512P Bedienungsanleitung

Sanyo

Sanyo VCC-4324P Bedienungsanleitung

Sanyo

Sanyo VCC-9800 Bedienungsanleitung

Sanyo

Sanyo VCC-HD5600 - Full HD 1080p Day/Night Pan-Tilt-Zoom... Bedienungsanleitung

Sanyo

Sanyo VCC-4312P Bedienungsanleitung

Sanyo

Sanyo VCC-6584DN - CCTV Camera Bedienungsanleitung

Sanyo

Sanyo VDC-D1785IRVP Bedienungsanleitung

Sanyo

Sanyo VCC-HD5400 Benutzerhandbuch

Sanyo

Sanyo VCC-4115P Bedienungsanleitung

Sanyo

Sanyo VCC-6594 Bedienungsanleitung

Sanyo

Sanyo VCC-HD2100 - Full HD 1080p Network Camera Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung