Sanyo VCB-3512T Bedienungsanleitung

INSTRUCTION MANUAL

B/W CCD Camera

VCB-3512T

About this manual

•Before installing and using the camera, please read this manual carefully. Be sure to

keep it handy for later reference.

L72K2/US2 GB 1998,2,24

SANYO INDUSTRIAL VIDEO

B/W VIDEO CAMERA LIMITED WARRANTY

OBLIGATIONS

Inordertoobtainwarrantyservice,theproductmustbedeliveredtoandpickedupfromanAuthorizedSanyoServiceCenter

attheuser’sexpense,unlessspecificallystatedotherwiseinthiswarranty.ThenamesandaddressesofAuthorizedSanyo

ServiceCentersmaybeobtainedbywritingtoSFSCorporation,SFC’swarrantyadministrator,atanyoftheaddresseslisted

below,orbycalling(toll-free)1-800-421-5013.

NewJerseyOffice

210RiserRoad

LittleFerry,NJ07643

201-641-3000 CaliforniaOffice

1200W.ArtesiaBlvd.

Compton,CA90220

310-537-5830 IllinoisOffice

900N.ArlingtonHeightsRd.

Itasca,IL60143

708-775-1414

THISWARRANTYISVALIDONLYONSANYOPRODUCTSPURCHASEDORRENTEDINTHEUNITEDSTATESOF

AMERICA,EXCLUDINGHAWAIIANDALLU.S.TERRITORIESANDPROTECTORATES.THISWARRANTYAPPLIESONLY

TOTHEORIGINALRETAILUSER.THEORIGINALDATEDBILLOFSALE,SALESSLIPORRENTALAGREEMENTMUSTBE

SUBMITTEDTOTHEAUTHORIZEDSANYOSERVICECENTERATTHETIMEWARRANTYSERVICEISREQUESTED.

SubjecttotheOBLIGATIONSaboveandEXCLUSIONSbelow,SANYOFISHER(USA)CORPORATIONwarrantsthisSANYO

productagainstdefectsinmaterialsandworkmanshipfortheperiodsspecifiedbelow.SFCwillrepairorreplace(atits

option)theproductandanyofitspartswhichfailtoconformtothiswarranty.Thewarrantyperiodcommencesonthedate

theproductwasfirstpurchasedorrentedatretail.

LABOR PARTS IMAGEDEVICE

2YEARS 2YEARS 2YEARS

EXCLUSIONS

Thiswarrantydoesnotcover(A)theadjustmentofcustomer-operatedcontrolsasexplainedintheappropriatemodel’s

instructionmanual,or(B)therepairofanyproductwhoseserialnumberhasbeenaltered,defacedorremoved.

Thiswarrantyshallnotapplytothecabinetorcosmeticparts,antenna,knobs,batteriesorimageburnstoprojectionor

picturetubescausedbyelectronicdevicesorgames.

Thiswarrantydoesnotapplytouncrating,setup,installation,removaloftheproductforrepairorreinstallationoftheproductafterrepair.

ThiswarrantydoesnotapplytorepairsorreplacementsnecessitatedbyanycausebeyondthecontrolofSFCincluding,but

notlimitedto,anymalfunction,defectorfailurecausedbyorresultingfromunauthorizedserviceorparts,improper

maintenance,operationcontrarytofurnishedinstructions,shippingortransitaccidents,modificationorrepairbytheuser,

abuse,misuse,neglect,accident,incorrectpowerlinevoltage,fire,floodorotherActsofGod,ornormalwearandtear.

TheforegoingisinlieuofallotherexpressedwarrantiesandSFCdoesnotassumeorauthorizeanypartytoassumeforit

anyotherobligationorliability.

THEDURATIONOFANYWARRANTIESWHICHMAYBEIMPLIEDBYLAW(INCLUDINGTHEWARRANTIESOF

MERCHANTABILITYANDFITNESS)ISLIMITEDTOTHETERMOFTHISWARRANTY.INNOEVENTSHALLSFCBELIABLE

FORSPECIAL,INCIDENTALORCONSEQUENTIALDAMAGESARISINGFROMOWNERSHIPORUSEOFTHISPRODUCT,

ORFORANYDELAYINTHEPERFORMANCEOFITSOBLIGATIONSUNDERTHISWARRANTYDUETOCAUSESBEYOND

ITSCONTROL.

SOMESTATESDONOTALLOWLIMITATIONSONHOWLONGANIMPLIEDWARRANTYLASTSAND/ORDONOTALLOW

THEEXCLUSIONORLIMITATIONOFCONSEQUENTIALDAMAGES,SOTHEABOVELIMITATIONSANDEXCLUSIONS

MAYNOTAPPLYTOYOU.

THISWARRANTYGIVESYOUSPECIFICLEGALRIGHTS.YOUMAYHAVEOTHERRIGHTS,WHICHVARYFROMSTATETOSTATE.

ATTENTION

Foryourprotectionintheeventoftheftorlossofthisproduct,pleasefillintheinformationbelowforyouownpersonalrecords.

Model No.___________________________________________ Serial No.___________________________________________

(Located on back or bottom side of unit.)

Date of Purchase ____________________________________ Purchase Price _____________________________________

Where Purchased _____________________________________________________________________________________________

L72K2/US2 GB 1998,2,24

14English

Depending on the conditions of use,

installation and environment, please be

sure to make the appropriate settings and

adjustments. If you need help with

installation and/or settings, please consult

your dealer.

CONTENTS

INFORMATION TO USER ..................................2

PRECAUTIONS...................................................3

PARTS NAMES...................................................4

MOUNTING THE LENS......................................6

POWER SOURCE................................................8

CONNECTIONS..................................................9

SETTINGS.........................................................10

TROUBLESHOOTING.......................................12

SPECIFICATIONS .............................................13

ACCESSORIES

1 mount adaptor (5 mm)................ 1 pc.

The mount adaptor must be used to

be able to install a mount lens on the

camera.

2Lens iris plug (4-pin) ........................1 pc.

FEATURES

•Built-in interline transfer method 1/2"

D, approx. 410,000 picture elements

•Low smear, anti-blooming, low lag, no

burning and no geometric distortion

using the D solid state image device.

•100% solid state components giving

excellent immunity to shock and

vibration

•Not subject to interference from

magnetic or electrostatic fields

•High sensitivity, minimum required

illumination of 0,07 lux with F1.2 lens

•Horizontal resolution, more than 570 TV

lines

•New backlight compensation function

(Active when using an auto-iris lens)

•Externally adjustable flange back

(mechanical focus)

•Low power consumption and quick start

•12 V D operation

L72K2/US2 GB 1998, 2, 24

English 1

Safety Guard

THIS SYMBOL INDICATES THAT

THERE ARE IMPORTANT

OPERATING AND

MAINTENANCE INSTRUCTIONS

IN THE LITERATURE

ACCOMPANYING THIS UNIT

WARNING:

TO PREVENT THE RISK OF FIRE OR

ELECTRIC SHOCK , DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR

MOISTURE

This installation should be made by a

qualified service person and should

conform to all local codes.

INFORMATION TO USER

For the customers in Canada

This lass B digital apparatus complies

with anadian I ES-003.

Pour la clientèle canadienne

et appareil numerique de la lasse B

est conforme a la norme NMB-003 du

anada.

This equipment has been tested and

found to comply with the limits for a

lass B digital device, pursuant to Part

15 of the F Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and

can radiate radio frequency energy and,

if not installed and used in accordance

with the instructions, may cause

harmful interference to radio

communications.

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does

cause harmful interference to radio or

television reception, which can be

determined by turning the equipment

off and on, the user is encouraged to

try to correct the interference by one or

more of the following measures:

– Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– onnect the equipment into an

outlet on a circuit different from that

to which the receiver is connected.

– onsult the dealer or an experienced

radio/TV technician for help.

This device complies with Part 15 of the

F Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference,

and (2) this device must accept any

interference received, including

interference that may cause undesired

operation.

hanges or modifications not expressly

approved by Sanyo may void the user’s

authority to operate this camera.

L72K2/US2 GB 1998, 2, 24

2English

PRECAUTIONS

In case of problem

Do not use the camera if smoke or a

strange odour comes from the unit, or if it

seems not to function correctly. Disconnect

the power cord immediately, and consult

your dealer (or a Sanyo Authorized Service

entre).

Do not open or modify

Do not open the cabinet, as it may be

dangerous and cause damage to the unit.

For internal settings and repairs, consult

your dealer (or a Sanyo Authorized Service

entre).

Do not put objects inside the unit

Make sure that no metal objects or

flammable substance get inside the camera.

If used with a foreign object inside, it could

cause a fire, short-circuits or damages.

If water or a liquid gets inside the camera,

disconnect the power cord immediately,

and consult your dealer (or a Sanyo

Authorized Service entre). Be careful to

protect the camera from rain, sea water,

etc.

Be careful when handling the unit

To prevent damages, do not drop the

camera or subject it to strong shock or

vibration.

Install away from electric or

magnetic fields

If installed close to a TV, radio transmitter,

magnet, electric motor, transformer, audio

speakers the magnetic field they generate

will distort the image.

Protect from humidity and dust

To prevent damages to the camera, do not

install it where there is greasy smoke or

steam, where the dampness may get too

high, or where there is a lot of dust.

Protect from high temperatures

Do not install close to stoves, or other heat

generating devices, such as spotlights, etc.,

or where it could be subject to direct

sunlight, as that could cause deformation,

discoloration or other damages.

Be careful when installing close to the

ceiling, in a kitchen or boiler room, as the

temperature may raise to high levels.

Install where the temperature range will

stay between –10˚ and 50˚ .

(no condensation)

Cleaning

•Dirt can be removed from the cabinet

by wiping it with a soft cloth. To

remove stains, wipe with a soft cloth

moistened with a soft detergent

solution and wrung dry, then wipe dry

with dry soft cloth.

•Do not use benzine, thinner or other

chemical product on the cabinet, as that

may cause deformation and paint

peeling. Before using a chemical cloth,

make sure to read all accompanying

instructions. Make sure that no plastic

or rubber material comes in contact

with the cabinet for a long period of

time, as that may cause damage or

paint peeling.

L72K2/US2 GB 1998, 2, 24

English 3

PARTS NAMES

1Video output connector (VIDEO OUT: BNC type)

onnect this connector to a device such as a V R or monitor

with a VIDEO IN connector.

212 V DC input terminal (12 V DC, GND)

3External sync composite video signal input connector

(VS IN: BNC type)

onnect to this connector the synchronizing signal output

from a synchronizing signal device or the composite signal of

a video distributor.

4Power indicator (POWER)

omes on when the power to the camera is on.

5Lens mount cap

The cap is installed to protect the lens mount section.

Remove the lens mount cap before installing a lens (sold

separately).

6Camera installation bracket

The bracket can be fixed at the top or bottom of the

camera. When fixing the bracket, be sure to use the longer

screws and install the shorter screws on the opposite side to

seal the openings.

CAUTION:

When installing the camera support, select a location

that can support the total weight of the camera and

accessories

1232

1Shorter screws: M3 x 4

2Longer screws: M3 x 6

3Camera mounting

screw hole: 1/4"-20

UNC

L72K2/US2 GB 1998, 2, 24

4English

PARTS NAMES

8Lens iris output connector (4 pin)

This 4-pin connector is used to send the D control signal

and power supply to an auto-iris type lens.

9Camera setup section (under the cover)

This unit factory settings are as indicated below. These

settings are for when using a 1/2 inch S mount DC

(without EE internal amplifier) type lens. However, if due to

installation conditions or environment the settings may need

to be modified for best results (see "SETTINGS"). To access

the controls, remove the cover fixing screw, then remove the

cover.

Control name Position

aHigh speed electronic shutter

switches (E S ) All OFF: 1/60 sec

bElectronic iris (EI)/

Backlight compensation (BLC)

switch

OFF

FFlange-back adjustment screw (FLANGE BACK ADJ )

GFlange-back lock screw (FLANGE BACK LOCK)

Flange-back adjustment

If the pick-up surface is not correctly positioned with relation

to the lens focal point, the picture will be out of focus (in

particular when using auto-iris power zoom lenses, sold

separately). If that is the case, adjust the flange-back position

as described below.

1Using a + screwdriver, loosen the FLANGE BACK LOCK

screw (M2:+).

Set the zoom lens to the maximum telephoto position,

set the focus using the focus ring on the lens.

2Set the zoom lens to the maximum wide angle position,

set the focus using the FLANGE BACK ADJ screw.

3Repeat steps 2 and 3, until the image stays in focus when

changing from a telephoto shot to a wide angle shot.

When the setting is complete, tighten the FLANGE

BACK LOCK screw.

LOCK

ADJ.

MOUNTING THE LENS

Check the lens mount

Do not use a lens if the length “L” is more than 7 mm.

That may damage the camera and prevent proper

installation.

Installation of a DC type auto-iris lens (sold

separately)

A 1/3 inch S mount type lens without EE amplifier circuit

that only uses a D power source. This camera can receive

(the A I LENS switch to the D type) a S mount type lens

without the need of an adaptor.

If the lens plug shape or wiring does not correspond, please

install the supplied plug as indicated in the pin layout table.

L72K2/US2 GB 1998, 2, 24

6English

MOUNTING THE LENS

Installation of a VIDEO type auto-iris lens

(sold separately)

A 1/2 or 2/3 inch mount type lens with EE amplifier circuit

that uses the video signal and a D power source.

1Remove the lens mount cap.

2Attach the supplied C mount adaptor (A) to the

auto-iris lens (B), then install the assembly on the camera.

3onnect the lens plug to the LENS connector on the side

of the camera.

If the lens plug shape or wiring does not correspond to

the specifications below, connect the supplied plug as

indicated.

•When using lenses from other makers, make sure that

the pins connections in the plug correspond to the

ones of the camera.

Refer to the lens specifications to check the pins

connections in the plug.

•If they are different than indicated, remove the original

plug and connect the supplied plug according to the

diagram.

4Set the A I LENS switch in the camera setup section to

the VIDEO position.

Pin layout

DC type lenses VIDEO type lenses

1Brake coil (–) +12 V D (50 mA max.)

2Brake coil (+) Not used

3Drive coil (+) Video output (1.0 Vp-p, high

impedance)

4Drive coil (–) Ground (for video signal and D

power)

2 (A) (B)

VIDEO

L72K2/US2 GB 1998, 2, 24

English 7

Compatible auto-iris lenses

1/2 inch Sanyo DC type lens 1/2 or 2/3 inch VIDEO type lens

V L- S12GY: Standard angle, f= 12 mm Standard angle, f= 9 mm

V L- S6GY: Wide angle, f= 6 mm Telephoto angle, f= 12 mm

V L- S3GY: Ultra-wide angle, f= 3.7 mm More telephoto angle, f= 16 mm

If using a VIDEO type auto-iris lens

•Set the ALC and LEVEL controls on the lens to adjust the iris. Normally the ALC volume

should be turned all the way to Av (Average).

•Depending on the type of lens used, the lens may not perform properly. In such a case,

adjust the LEVEL volume on the lens casing to correct.

POWER SOURCE

onnect D 12V power supply to 12V DC input terminal on

the camera.

N : non connect

+–

L72K2/US2 GB 1998, 2, 24

8English

Andere Sanyo Sicherheitskamera Handbücher

Sanyo

Sanyo VCC-HD2100 - Full HD 1080p Network Camera Bedienungsanleitung

Sanyo

Sanyo VCC-P7574N - 1/4" Color CCD Indoor Mini Dome... Bedienungsanleitung

Sanyo

Sanyo VCB-3385P Bedienungsanleitung

Sanyo

Sanyo VDC-DP7584 - 1/4" Color CCD Vandal-Resistant Dome... Bedienungsanleitung

Sanyo

Sanyo VCC-9684VA - 1/4" Color CCD Indoor Mini Dome... Bedienungsanleitung

Sanyo

Sanyo VDC-DP7584S - 1/4" Color CCD Vandal-Resistant Dome... Bedienungsanleitung

Sanyo

Sanyo VCC-4794E - 1/3" Color CCD DSP Day/Night... Bedienungsanleitung

Sanyo

Sanyo VCC-HD5400 Bedienungsanleitung

Sanyo

Sanyo VCC-3944 - 1/4" Color CCD DSP Camera Bedienungsanleitung

Sanyo

Sanyo VCC-3912 Bedienungsanleitung

Sanyo

Sanyo VCC-HD2100P Bedienungsanleitung

Sanyo

Sanyo VCC-7912P Bedienungsanleitung

Sanyo

Sanyo VCC-3974P Bedienungsanleitung

Sanyo

Sanyo VCC-6594P Bedienungsanleitung

Sanyo

Sanyo VCB-3574IR Bedienungsanleitung

Sanyo

Sanyo VDC-DP7584 - 1/4" Color CCD Vandal-Resistant Dome... Bedienungsanleitung

Sanyo

Sanyo VCC-4312P Bedienungsanleitung

Sanyo

Sanyo VCC-XV400 Bedienungsanleitung

Sanyo

Sanyo VCC-HD5600 - Full HD 1080p Day/Night Pan-Tilt-Zoom... Bedienungsanleitung

Sanyo

Sanyo VCC-5984 Bedienungsanleitung

Sanyo

Sanyo VCB-333OP Bedienungsanleitung

Sanyo

Sanyo VCC-9624 Bedienungsanleitung

Sanyo

Sanyo VCC-XZ200P Bedienungsanleitung

Sanyo

Sanyo VDC-HD3100P/HD3100 Benutzerhandbuch

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung