Sanyo VCC-5974 Bedienungsanleitung

INSTRUCTION MANUAL

COLOR CCD Camera

VCC-5974

About this manual

•Before installing and using the camera, please read this manual carefully. Be sure to

keep it handy for later reference.

L53P4/US GB 1998, 3, 11

SANYO INDUSTRIAL VIDEO

COLOR VIDEO CAMERA LIMITED WARRANTY

OBLIGATIONS

In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center

at the user’s expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo

Service Centers may be obtained by writing to SFS Corporation, SFC’s warranty administrator, at any of the addresses listed

below, or by calling (toll-free) 1-800-421-5013.

New Jersey Office

210 Riser Road

Little Ferry, NJ 07643

201-641-3000

California Office

1200 W. Artesia Blvd.

Compton, CA 90220

310-537-5830

Illinois Office

900 N. Arlington Heights Rd.

Itasca, IL 60143

708-775-1414

THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF

AMERICA, EXCLUDING HAWAII AND ALL U.S. TERRITORIES AND PROTECTORATES. THIS WARRANTY APPLIES ONLY

TO THE ORIGINAL RETAIL USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE

SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED.

Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO FISHER COMPANY warrants this SANYO product

against defects in materials and workmanship for the periods specified below. SFC will repair or replace (at its option) the

product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the product

was first purchased or rented at retail.

LABOR PARTS IMAGE DEVICE

2 YEARS 2 YEARS 2 YEARS

EXCLUSIONS

This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model’s

instruction manual, or (B) the repair of any product whose serial number has been altered, defaced or removed.

This warranty shall not apply to the cabinet or cosmetic parts, antenna, knobs, batteries or image burns to projection or

picture tubes caused by electronic devices or games.

This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.

This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but

not limited to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper

maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user,

abuse, misuse, neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear.

The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it

any other obligation or liability.

THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS) IS LIMITED TO THE TERM OF THIS WARRANTY. IN NO EVENT SHALL SFC BE LIABLE

FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT,

OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND

ITS CONTROL.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW

THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS

MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.

ATTENTION

For your protection in the event of theft or loss of this product, please fill in the information below for you own personal records.

Model No.___________________________________________ Serial No.___________________________________________

(Located on back or bottom side of unit.)

Date of Purchase ____________________________________ Purchase Price _____________________________________

Where Purchased _____________________________________________________________________________________________

L53P4/US GB 1998, 3, 11

Depending on the conditions of use,

installation and environment, please be sure

to make the appropriate settings and

adjustments. If you need help with installation

and/or settings, please consult your dealer.

CONTENTS

INFORMATION TO USER ..................................2

PRECAUTIONS...................................................3

PARTS NAMES...................................................4

MOUNTING THE LENS......................................7

CONNECTIONS..................................................9

SETTINGS.........................................................10

USING THE ON-SCREEN MENUS....................13

ADJUSTMENTS................................................14

TROUBLESHOOTING.......................................26

MENU DISPLAY...............................................27

SPECIFICATIONS .............................................29

ACCESSORIES

1C mount adaptor 5 mm).....................1 pc.

The C mount adaptor must be used to be

able to install a C mount lens on the

camera.

2Lens iris plug 4-pin).............................1 pc.

FEATURES

•Built-in interline transfer method 1/3" CCD,

approx. 410,000 picture elements

•Low smear, anti-blooming, low lag, no

burning and no geometric distortion using

the CCD solid state image device.

•100% solid state components giving

excellent immunity to shock and vibration

•Not subject to interference from magnetic

or electrostatic fields

•High sensitivity, minimum required

illumination is 0.9 lux F1.2, AGC Gain:

High, incandescent lighting)

•Horizontal resolution, more than 470 TV

lines

•Power supply: 24 V AC operation

L53P4/US GB 1998, 3, 11

English 1

Safety Guard

THIS SYMBOL INDICATES THAT

THERE ARE IMPORTANT

OPERATING AND

MAINTENANCE INSTRUCTIONS

IN THE LITERATURE

ACCOMPANYING THIS UNIT

WARNING:

TO PREVENT THE RISK OF FIRE OR

ELECTRIC SHOCK , DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE

This installation should be made by a qualified

service person and should conform to all local

codes.

INFORMATION TO USER

For the customers in Canada

This Class B digital apparatus meets all

requirements of the Canadian Interference-

Causing Equipment Regulations.

Pour la clientèle canadienne

Cet appareil numerique de la Classe B respecte

toutes les exigences du Reglement sur le

material brouilleur du Canada.

This equipment has been tested and found

to comply with the limits for a Class B

digital device, pursuant to Part 15 of the

FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does cause

harmful interference to radio or television

reception, which can be determined by

turning the equipment off and on, the

user is encouraged to try to correct the

interference by one or more of the

following measures:

–Reorient or relocate the receiving

antenna.

–Increase the separation between the

equipment and receiver.

–Connect the equipment into an outlet

on a circuit different from that to which

the receiver is connected.

–Consult the dealer or an experienced

radio/TV technician for help.

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: 1) This device

may not cause harmful interference, and

2) this device must accept any

interference received, including

interference that may cause undesired

operation.

Changes or modifications not expressly

approved by Sanyo may void the user’s

authority to operate this camera.

ENGLISH

L53P4/US GB 1998, 3, 11

2 English

PRECAUTIONS

In case of problem

Do not use the camera if smoke or a strange

odour comes from the unit, or if it seems not

to function correctly. Disconnect the power

cord immediately, and consult your dealer or

a Sanyo Authorized Service Centre).

Do not open or modify

Do not open the cabinet, as it may be

dangerous and cause damage to the unit. For

internal settings and repairs, consult your

dealer or a Sanyo Authorized Service Centre).

Do not put objects inside the unit

Make sure that no metal objects or flammable

substance get inside the camera. If used with

a foreign object inside, it could cause a fire,

short-circuits or damages.

If water or a liquid gets inside the camera,

disconnect the power cord immediately, and

consult your dealer or a Sanyo Authorized

Service Centre). Be careful to protect the

camera from rain, sea water, etc.

Be careful when handling the unit

To prevent damages, do not drop the camera

or subject it to strong shock or vibration.

Install away from electric or magnetic

fields

If installed close to a TV, radio transmitter,

magnet, electric motor, transformer, audio

speakers the magnetic field they generate will

distort the image.

Protect from humidity and dust

To prevent damages to the camera, do not

install it where there is greasy smoke or

steam, where the dampness may get too

high, or where there is a lot of dust.

Protect from high temperatures

Do not install close to stoves, or other heat

generating devices, such as spotlights, etc., or

where it could be subject to direct sunlight, as

that could cause deformation, discoloration or

other damages.

Be careful when installing close to the ceiling,

in a kitchen or boiler room, as the

temperature may raise to high levels.

Install where the temperature range will stay

between –10˚C and 50˚C.

no condensation)

Cleaning

•Dirt can be removed from the cabinet by

wiping it with a soft cloth. To remove

stains, wipe with a soft cloth moistened

with a soft detergent solution and wrung

dry, then wipe dry with dry soft cloth.

•Do not use benzine, thinner or other

chemical product on the cabinet, as that

may cause deformation and paint peeling.

Before using a chemical cloth, make sure

to read all accompanying instructions.

Make sure that no plastic or rubber

material comes in contact with the cabinet

for a long period of time, as that may

cause damage or paint peeling.

L53P4/US GB 1998, 3, 11

English 3

PARTS NAMES

1Lens iris output connector (4 pin)

This 4-pin connector is used to send the DC control signal and

power supply to an auto-iris type lens.

2Auto white balance push lock button (AWB LOCK)

3Menu setting button (SET)

Connect the camera to the monitor, then press the SET button

for about 3 seconds to display the on-screen menu.

4Cursor button (CURSOR)

j: Press this button to move the cursor up.

c: Press this button to move the cursor to the right, or to

turn the settings ON/OFF etc.

d: Press this button to move the cursor to the left, or to

turn the settings ON/OFF.

l: Press this button to move the cursor down.

5Flange-back lock screw (FLANGE BACK LOCK)

6Flange-back adjustment screw (FLANGE BACK ADJ )

7Lens mount cap

The cap is installed to protect the lens mount section.

Remove the lens mount cap before installing a lens sold

separately).

8Camera installation bracket

The bracket can be fixed at the top or bottom of the camera.

When fixing the bracket, be sure to use the longer screws and

install the shorter screws on the opposite side to seal the

openings.

CAUTION:

When installing the camera support, select a location

that can support the total weight of the camera and

accessories

1232

1Shorter screws: M3 x 4

2Longer screws: M3 x 6

3Camera mounting

screw hole:

1/4"-20 UNC

L53P4/US GB 1998, 3, 11

4 English

PARTS NAMES

9Camera setup section (under the cover)

This unit factory settings are as indicated below. These settings

are for when using a 1/3 inch CS mount DC without EE internal

amplifier) type lens. However, if due to installation conditions or

environment the settings may need to be modified for best

results see "SETTINGS"). To access the controls, remove the

cover fixing screw, then remove the cover.

Control name Position

aHigh speed electronic shutter

switches (ES)

All OFF: 1/60 sec

bInternal/Line lock switch (SYNC) INT

cAuto gain control switch (AGC) ON

dWhite balance switch (WB) all ON: ATW

eBacklight compensation switch

(BLC)

fElectronic iris (EI)/

Auto iris (AI) switch

gAuto-iris lens switch (A I LENS) DC

Notes:

•When using a 1/2 or 2/3 inch C mount VIDEO with EE

internal amplifier) auto-iris type lens, set the A I LENS switch

to the VIDEO position.

The settings entered in the camera setup section can be

displayed using the on-screen menu.

•If not using an auto-iris lens, make sure the BLC switch is set

to OFF.

2341

6785910

INT

OFF

OFF EI

AIONES LL ON ON WB

BLCSYNC FL

AGC

L53P4/US GB 1998, 3, 11

English 5

FVideo output connector (VIDEO OUT: BNC type)

Connect this connector to a device such as a VCR or monitor

with a VIDEO IN connector.

GExternal sync composite video signal input connector

(VBS IN: BNC type)

Connect to this connector the synchronizing signal output from

a synchronizing signal device or the composite signal of a video

distributor.

HPower indicator (POWER)

Comes on when the power to the camera is on.

I24 V AC input terminal (24 V AC, GND)

With this camera use only the 24 V AC power adaptor model

No. VPT-115 available from Sanyo.

Power supply connections

Use a 3 wire grounded cable 22 AWG or more), and connect as

shown by the illustration.

CAUTION:

•To prevent camera and/or AC adaptor failure, pay close

attention to polarity when making the connections.

•To prevent fire hazard any UL listed wire rated VW-1,

should be used for the 24 V AC cable input terminal.

GND

AC AC

L53P4/US GB 1998, 3, 11

6 English

PARTS NAMES

LOCK

ADJ.

Flange-back adjustment

If the pick-up surface is not correctly positioned with relation to

the lens focal point, the picture will be out of focus in particular

when using auto-iris power zoom lenses, sold separately). If that

is the case, adjust the flange-back position as described below.

1Using a + screwdriver, loosen the FLANGE BACK LOCK

screw M2:+).

Set the zoom lens to the maximum telephoto position, set

the focus using the focus ring on the lens.

2Set the zoom lens to the maximum wide angle position, set

the focus using the FLANGE BACK ADJ screw.

3Repeat steps 2 and 3, until the image stays in focus when

changing from a telephoto shot to a wide angle shot.

When the setting is complete, tighten the FLANGE BACK

LOCK screw.

MOUNTING THE LENS

Check the lens mount

Do not use a lens if the length “L” is more than 5 mm. That

may damage the camera and prevent proper installation.

Installation of a DC type auto-iris lens (sold

separately)

A 1/3 inch CS mount type lens without EE amplifier circuit that

only uses a DC power source. This camera can receive the A I

LENS switch to the DC type) a CS mount type lens without the

need of an adaptor.

If the lens plug shape or wiring does not correspond, please

install the supplied plug as indicated in the pin layout table.

L53P4/US GB 1998, 3, 11

English 7

MOUNTING THE LENS

Installation of a VIDEO type auto-iris lens

(sold separately)

A 1/2 or 2/3 inch C mount type lens with EE amplifier circuit

that uses the video signal and a DC power source.

1Remove the lens mount cap.

2Attach the supplied C mount adaptor (A) to the auto-iris

lens (B), then install the assembly on the camera.

3Connect the lens plug to the LENS connector on the side of

the camera.

If the lens plug shape or wiring does not correspond to the

specifications below, connect the supplied plug as indicated.

•When using lenses from other makers, make sure that the

pins connections in the plug correspond to the ones of

the camera.

Refer to the lens specifications to check the pins

connections in the plug.

•If they are different than indicated, remove the original

plug and connect the supplied plug according to the

diagram.

4Set the A I LENS switch in the camera setup section to the

VIDEO position.

Pin layout

DC type lenses VIDEO type lenses

1Brake coil –) +12 V DC 50 mA max.)

2Brake coil +) Not used

3Drive coil +) Video output 1.0 Vp-p, high

impedance)

4Drive coil –) Ground for video signal and DC

power)

VIDEO

2 (A) (B)

L53P4/US GB 1998, 3, 11

8 English

Andere Handbücher für VCC-5974

Inhaltsverzeichnis

Andere Sanyo Sicherheitskamera Handbücher

Sanyo

Sanyo VCB-3440P Bedienungsanleitung

Sanyo

Sanyo VCB-3424 Bedienungsanleitung

Sanyo

Sanyo VCC-6584E - 1/3" Color CCD DSP High-Resolution... Bedienungsanleitung

Sanyo

Sanyo VCC-HD4600 - Full HD 1080p Day/Night Network... Bedienungsanleitung

Sanyo

Sanyo VCC-WB4000P Bedienungsanleitung

Sanyo

Sanyo VCC-WB2000 Bedienungsanleitung

Sanyo

Sanyo VDC-DP7584S - 1/4" Color CCD Vandal-Resistant Dome... Bedienungsanleitung

Sanyo

Sanyo Security Camera Bedienungsanleitung

Sanyo

Sanyo VDC-DP7584 - 1/4" Color CCD Vandal-Resistant Dome... Bedienungsanleitung

Sanyo

Sanyo VCB-3574IRP Bedienungsanleitung

Sanyo

Sanyo VDC-C1074VA Bedienungsanleitung

Sanyo

Sanyo VCC-3944 - 1/4" Color CCD DSP Camera Bedienungsanleitung

Sanyo

Sanyo VCC-HD2100 - Full HD 1080p Network Camera Bedienungsanleitung

Sanyo

Sanyo VCC-HD5600 - Full HD 1080p Day/Night Pan-Tilt-Zoom... Bedienungsanleitung

Sanyo

Sanyo VCC-4324 Bedienungsanleitung

Sanyo

Sanyo VCC-HD2500 - Full HD 1080p Network Camera Bedienungsanleitung

Sanyo

Sanyo VDC-D1185VP Bedienungsanleitung

Sanyo

Sanyo VDC-HD3500P Bedienungsanleitung

Sanyo

Sanyo VDC-C1024V Bedienungsanleitung

Sanyo

Sanyo VCC-3972P Bedienungsanleitung

Sanyo

Sanyo VCC-P7575P Pan-Focus Bedienungsanleitung

Sanyo

Sanyo VCC-5974 Bedienungsanleitung

Sanyo

Sanyo VCC-HD2100P Bedienungsanleitung

Sanyo

Sanyo VCB-3454 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung