Sanyo VCC-5974 Bedienungsanleitung
INSTRUCTION MANUAL
COLOR CCD Camera
VCC-5974
About this manual
•Before installing and using the camera, please read this manual carefully. Be sure to
keep it handy for later reference.
L53P4/USGB1998,3,11
SANYO INDUSTRIAL VIDEO
COLOR VIDEO CAMERA LIMITED WARRANTY
OBLIGATIONS
Inordertoobtainwarrantyservice,theproductmustbedeliveredtoandpickedupfromanAuthorizedSanyoServiceCenter
attheuser’sexpense,unlessspecificallystatedotherwiseinthiswarranty.ThenamesandaddressesofAuthorizedSanyo
ServiceCentersmaybeobtainedbywritingtoSFSCorporation,SFC’swarrantyadministrator,atanyoftheaddresseslisted
below,orbycalling(toll-free)1-800-421-5013.
NewJerseyOffice
210RiserRoad
LittleFerry,NJ07643
I,Afg.,E-4213.3.43621-apick4AfnSzeYTysEeg.,E-4213.3.43621-a5gUci4213.3wtrseyOff-NDUSTRIAL0uBc,orreyhhEIcRsoigwtrCh38076DUS213R6DU-26.16U-26.16U-26.16U-26.16U-26.16U-142.47602ant16U-i26.141ys9o1ad
Depending on the conditions of use,
installation and environment, please be sure
to make the appropriate settings and
adjustments. If you need help with installation
and/or settings, please consult your dealer.
CONTENTS
INFORMATION TO USER..................................2
PRECAUTIONS...................................................3
PARTS NAMES...................................................4
MOUNTING THE LENS......................................7
CONNECTIONS..................................................9
SETTINGS.........................................................10
USING THE ON-SCREEN MENUS....................13
ADJUSTMENTS................................................14
TROUBLESHOOTING.......................................26
MENU DISPLAY...............................................27
SPECIFICATIONS.............................................29
ACCESSORIES
1C mount adaptor 5 mm).....................1 pc.
The C mount adaptor must be used to be
able to install a C mount lens on the
camera.
2Lens iris plug 4-pin).............................1 pc.
12
FEATURES
•Built-in interline transfer method 1/3" CCD,
approx. 410,000 picture elements
•Low smear, anti-blooming, low lag, no
burning and no geometric distortion using
the CCD solid state image device.
•100% solid state components giving
excellent immunity to shock and vibration
•Not subject to interference from magnetic
or electrostatic fields
•High sensitivity, minimum required
illumination is 0.9 lux F1.2, AGC Gain:
High, incandescent lighting)
•Horizontal resolution, more than 470 TV
lines
•Power supply: 24 V AC operation
L53P4/US GB 1998, 3, 11
English 1
Safety Guard
THIS SYMBOL INDICATES THAT
THERE ARE IMPORTANT
OPERATING AND
MAINTENANCE INSTRUCTIONS
IN THE LITERATURE
ACCOMPANYING THIS UNIT
WARNING:
TO PREVENT THE RISK OF FIRE OR
ELECTRIC SHOCK , DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE
This installation should be made by a qualified
service person and should conform to all local
codes.
INFORMATION TO USER
For the customers in Canada
This Class B digital apparatus meets all
requirements of the Canadian Interference-
Causing Equipment Regulations.
Pour la clientèle canadienne
Cet appareil numerique de la Classe B respecte
toutes les exigences du Reglement sur le
material brouilleur du Canada.
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
–Reorient or relocate the receiving
antenna.
–Increase the separation between the
equipment and receiver.
–Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
–Consult the dealer or an experienced
radio/TV technician for help.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: 1) This device
may not cause harmful interference, and
2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Changes or modifications not expressly
approved by Sanyo may void the user’s
authority to operate this camera.
ENGLISH
L53P4/US GB 1998, 3, 11
2 English
PRECAUTIONS
In case of problem
Do not use the camera if smoke or a strange
odour comes from the unit, or if it seems not
to function correctly. Disconnect the power
cord immediately, and consult your dealer or
a Sanyo Authorized Service Centre).
Do not open or modify
Do not open the cabinet, as it may be
dangerous and cause damage to the unit. For
internal settings and repairs, consult your
dealer or a Sanyo Authorized Service Centre).
Do not put objects inside the unit
Make sure that no metal objects or flammable
substance get inside the camera. If used with
a foreign object inside, it could cause a fire,
short-circuits or damages.
If water or a liquid gets inside the camera,
disconnect the power cord immediately, and
consult your dealer or a Sanyo Authorized
Service Centre). Be careful to protect the
camera from rain, sea water, etc.
Be careful when handling the unit
To prevent damages, do not drop the camera
or subject it to strong shock or vibration.
Install away from electric or magnetic
fields
If installed close to a TV, radio transmitter,
magnet, electric motor, transformer, audio
speakers the magnetic field they generate will
distort the image.
Protect from humidity and dust
To prevent damages to the camera, do not
install it where there is greasy smoke or
steam, where the dampness may get too
high, or where there is a lot of dust.
Protect from high temperatures
Do not install close to stoves, or other heat
generating devices, such as spotlights, etc., or
where it could be subject to direct sunlight, as
that could cause deformation, discoloration or
other damages.
Be careful when installing close to the ceiling,
in a kitchen or boiler room, as the
temperature may raise to high levels.
Install where the temperature range will stay
between –10˚C and 50˚C.
no condensation)
Cleaning
•Dirt can be removed from the cabinet by
wiping it with a soft cloth. To remove
stains, wipe with a soft cloth moistened
with a soft detergent solution and wrung
dry, then wipe dry with dry soft cloth.
•Do not use benzine, thinner or other
chemical product on the cabinet, as that
may cause deformation and paint peeling.
Before using a chemical cloth, make sure
to read all accompanying instructions.
Make sure that no plastic or rubber
material comes in contact with the cabinet
for a long period of time, as that may
cause damage or paint peeling.
L53P4/US GB 1998, 3, 11
English 3
PARTS NAMES
1Lens iris output connector (4 pin)
This 4-pin connector is used to send the DC control signal and
power supply to an auto-iris type lens.
2Auto white balance push lock button (AWB LOCK)
3Menu setting button (SET)
Connect the camera to the monitor, then press the SET button
for about 3 seconds to display the on-screen menu.
4Cursor button (CURSOR)
j: Press this button to move the cursor up.
c: Press this button to move the cursor to the right, or to
turn the settings ON/OFF etc.
d: Press this button to move the cursor to the left, or to
turn the settings ON/OFF.
l: Press this button to move the cursor down.
5Flange-back lock screw (FLANGE BACK LOCK)
6Flange-back adjustment screw (FLANGE BACK ADJ )
7Lens mount cap
The cap is installed to protect the lens mount section.
Remove the lens mount cap before installing a lens sold
separately).
8Camera installation bracket
The bracket can be fixed at the top or bottom of the camera.
When fixing the bracket, be sure to use the longer screws and
install the shorter screws on the opposite side to seal the
openings.
CAUTION:
When installing the camera support, select a location
that can support the total weight of the camera and
accessories
1232
1
8
74
32
1
4
1
2
3
5
6
1Shorter screws: M3 x 4
2Longer screws: M3 x 6
3Camera mounting
screw hole:
1/4"-20 UNC
L53P4/US GB 1998, 3, 11
4 English
PARTS NAMES
9Camera setup section (under the cover)
This unit factory settings are as indicated below. These settings
are for when using a 1/3 inch CS mount DC without EE internal
amplifier) type lens. However, if due to installation conditions or
environment the settings may need to be modified for best
results see "SETTINGS"). To access the controls, remove the
cover fixing screw, then remove the cover.
Control name Position
aHigh speed electronic shutter
switches (ES)
All OFF: 1/60 sec
bInternal/Line lock switch (SYNC) INT
cAuto gain control switch (AGC) ON
dWhite balance switch (WB) all ON: ATW
eBacklight compensation switch
(BLC)
ON
fElectronic iris (EI)/
Auto iris (AI) switch
AI
gAuto-iris lens switch (A I LENS) DC
Notes:
•When using a 1/2 or 2/3 inch C mount VIDEO with EE
internal amplifier) auto-iris type lens, set the A I LENS switch
to the VIDEO position.
The settings entered in the camera setup section can be
displayed using the on-screen menu.
•If not using an auto-iris lens, make sure the BLC switch is set
to OFF.
9
2341
a
ON
6785910
23
INT
1
OFF
78
OFF
OFF EI
I
R
I
S
AIONES LL ON ON WB
BLCSYNC FL
AGC
b
c
d
e
f
g
L53P4/US GB 1998, 3, 11
FVideo output connector (VIDEO OUT: BNC type)
Connect this connector to a device such as a VCR or monitor
with a VIDEO IN connector.
GExternal sync composite video signal input connector
(VBS IN: BNC type)
Connect to this connector the synchronizing signal output from
a synchronizing signal device or the composite signal of a video
distributor.
HPower indicator (POWER)
Comes on when the power to the camera is on.
I24 V AC input terminal (24 V AC, GND)
With this camera use only the 24 V AC power adaptor model
No. VPT-115 available from Sanyo.
Power supply connections
Use a 3 wire grounded cable 22 AWG or more), and connect as
shown by the illustration.
CAUTION:
•To prevent camera and/or AC adaptor failure, pay close
attention to polarity when making the connections.
•To prevent fire hazard any UL listed wire rated VW-1,
should be used for the 24 V AC cable input terminal.
FH
I
G
GND
AC AC
L53P4/US GB 1998, 3, 11
6 English
PARTS NAMES
1
1
3
LOCK
2
ADJ.
Flange-back adjustment
If the pick-up surface is not correctly positioned with relation to
the lens focal point, the picture will be out of focus in particular
when using auto-iris power zoom lenses, sold separately). If that
is the case, adjust the flange-back position as described below.
1Using a + screwdriver, loosen the FLANGE BACK LOCK
screw M2:+).
Set the zoom lens to the maximum telephoto position, set
the focus using the focus ring on the lens.
2Set the zoom lens to the maximum wide angle position, set
the focus using the FLANGE BACK ADJ screw.
3Repeat steps 2 and 3, until the image stays in focus when
changing from a telephoto shot to a wide angle shot.
When the setting is complete, tighten the FLANGE BACK
LOCK screw.
MOUNTING THE LENS
Check the lens mount
Do not use a lens if the length “L” is more than 5 mm. That
may damage the camera and prevent proper installation.
Installation of a DC type auto-iris lens (sold
separately)
A 1/3 inch CS mount type lens without EE amplifier circuit that
only uses a DC power source. This camera can receive the A I
LENS switch to the DC type) a CS mount type lens without the
need of an adaptor.
If the lens plug shape or wiring does not correspond, please
install the supplied plug as indicated in the pin layout table.
L
L53P4/US GB 1998, 3, 11
English 7
MOUNTING THE LENS
Installation of a VIDEO type auto-iris lens
(sold separately)
A 1/2 or 2/3 inch C mount type lens with EE amplifier circuit
that uses the video signal and a DC power source.
1Remove the lens mount cap.
2Attach the supplied C mount adaptor (A) to the auto-iris
lens (B), then install the assembly on the camera.
3Connect the lens plug to the LENS connector on the side of
the camera.
If the lens plug shape or wiring does not correspond to the
specifications below, connect the supplied plug as indicated.
•When using lenses from other makers, make sure that the
pins connections in the plug correspond to the ones of
the camera.
Refer to the lens specifications to check the pins
connections in the plug.
•If they are different than indicated, remove the original
plug and connect the supplied plug according to the
diagram.
4Set the A I LENS switch in the camera setup section to the
VIDEO position.
Pin layout
DC type lenses VIDEO type lenses
1Brake coil –) +12 V DC 50 mA max.)
2Brake coil +) Not used
3Drive coil +) Video output 1.0 Vp-p, high
impedance)
4Drive coil –) Ground for video signal and DC
power)
DC
VIDEO
4
2 (A) (B)
3
31
2
4
4
1
2
3
L53P4/US GB 1998, 3, 11
8 English
Andere Handbücher für VCC-5974
1
Inhaltsverzeichnis
Andere Sanyo Sicherheitskamera Handbücher
Sanyo
Sanyo VDC-DP9575P Bedienungsanleitung
Sanyo
Sanyo VCC-5972P Bedienungsanleitung
Sanyo
Sanyo VCC-4324P Bedienungsanleitung
Sanyo
Sanyo VCC-XZ600 Bedienungsanleitung
Sanyo
Sanyo VCC-9600 Bedienungsanleitung
Sanyo
Sanyo VCC-5974P Bedienungsanleitung
Sanyo
Sanyo VCC-P7574N - 1/4" Color CCD Indoor Mini Dome... Bedienungsanleitung
Sanyo
Sanyo VCC-HD2500 - Full HD 1080p Network Camera Bedienungsanleitung
Sanyo
Sanyo VCC-P6784 Bedienungsanleitung
Sanyo
Sanyo VCC-P7575P Pan-Focus Bedienungsanleitung
Sanyo
Sanyo VCB-3424 Bedienungsanleitung
Sanyo
Sanyo VCC-4594 Bedienungsanleitung
Sanyo
Sanyo VCC-5884EA - 1/3" Color CCD DSP High-Resolution... Bedienungsanleitung
Sanyo
Sanyo VCC-N6695P Bedienungsanleitung
Sanyo
Sanyo VCC-HD5600P Series Bedienungsanleitung
Sanyo
Sanyo VCC-WD8874 - Wide Dynamic Range Color Bedienungsanleitung
Sanyo
Sanyo VDC-D1184VA Bedienungsanleitung
Sanyo
Sanyo VCB-3444 Bedienungsanleitung
Sanyo
Sanyo VDC-DP7584N - 1/4" Color CCD Vandal-Resistant Dome... Bedienungsanleitung
Sanyo
Sanyo VCC-HD2300 - Full HD 1080p Network Camera Bedienungsanleitung
