Sartorius 2405 Benutzerhandbuch

Digital Micro Balances

2405

Instructions for installation and operation

1. UNPACKING

2. INSTALLATION OF THE BALANCE

2.1. Checking the voltage setting

2.2. Detaching the transport arrestment

2.3. Assembling the balance

2.4. Inserting the glass plates

2.5. Leveling the balance

3. DESCRIPTION OF THE OPERATING KNOBS

4. CHECKING AND ADJUSTING

4.1. Focusing the projection scale

4.2. Zero point

4.3. Sensitivity

5. WEIGHING PROCEDURES

6. SUPPLEMENT

6.1. Accuracy of the built-in set of weights

6.2. Correction of the weighing result

6.3. Determination of the air density

6.4. Conditions for installing micro balances

7. TECHNICAL DATA

1. Unpacking

1.1. Carefully remove the balance from their cartons.

1.2. Carefully unpack accessories.

2. INSTALLATION

2.0.1. IMPORTANT: see supplement 6.1. to 6.4.

2.0.2. Remove outer and inner lid.

2.1. Checking the voltage setting:

2.1.1. Place balance on the rear on to the plastic dust cover. Push the cover plate in the base plate aside

and change connecting wires, if necessary. Close the cover plate and set up the balance. Remove the

adhesive tape carefully and wipe off the arrears with alcohol.

2.2. Detaching the transport arrestment:

2.2.1. Weight application must indicate “29.99”.

2.2.2. Take off cover of the damping pot.

2.2.3. 3 Loosen knurled nuts, remove paper strips, swing aside springs and retighten nuts.

Remove cardboard strip.

2.2.4. Take out balance beam. Take off 3 plastic discs (1). Loosen 3 knurled nuts (2), swing aside springs

and retighten nuts.

2.2.5. Remove cardboard strip.

Connect balance to the mains. Press gray push button (see 3.1.).

2.2.6. Remove brackets at the ends of the locking bars of the weight application.

2.2.7. Pull out bars carefully.

2.3. Assembling the balance:

2.3.1. Check arrestment pins (1), damping (2) and bearing (3) and clean, if necessary.

2.3.2. Check knife-edges and bearing and clean, if necessary.

2.3.3. Set balance beam on to the arrestment pins (1). The knife-edge must not come into contact with the

bearing.

2.3.4. Place cover plate on to the damping pot and turn anti-clockwise until the slit the cover plate runs paral-

lel with the balance beam. Turn clamp clockwise until it locks.

2.3.5. Check stirrup plate and clean, if necessary. Set stirrup plate on to the arrestment pins.

2.3.6.2. Unscrew 2 knurled nuts and take off bow.

2.3.7. Attach stirrup and insert it.

2.3.8. Unscrew 2 knurled nuts and take down carefully the locking plate for the weights. Put back the perfo-

rated plate afterwards.

2.3.9. Attach lamp housing and plug in the cable.

2.3.10. Place the inside hood on to the balance.

2.3.11. Swing out pan lifting device. Open upper sliding door and attach pan bow.

2.4. Inserting the glass plates:

2.4.1. Place glass plate into the balance and close upper sliding door. Put the balance pan on to the holder

and swing in the pan.

2.4.2. Place glass plate into the balance and close sliding door.

2.4.3. Put locking screws for the front plate into position.

2.4.4. Fasten front plate.

2.4.5.Turn weight application to “0.00” and set micrometer to “00”.

Inhaltsverzeichnis

Andere Sartorius Skala Handbücher

Sartorius

Sartorius Cubis MCE Series Bedienungsanleitung

Sartorius

Sartorius 1100 Benutzerhandbuch

Sartorius

Sartorius EA Bedienungsanleitung

Sartorius

Sartorius Cubis MCA Series Bedienungsanleitung

Sartorius

Sartorius BL310 Bedienungsanleitung

Sartorius

Sartorius GPC65-CW Bedienungsanleitung

Sartorius

Sartorius U 3600 Bedienungsanleitung

Sartorius

Sartorius ME215 Bedienungsanleitung

Sartorius

Sartorius PMA series Originalbetriebsanleitung

Sartorius

Sartorius M3P Bedienungsanleitung

Sartorius

Sartorius U 4100 Bedienungsanleitung

Sartorius

Sartorius Master series Bedienungsanleitung

Sartorius

Sartorius PMA Evolution Bedienungsanleitung

Sartorius

Sartorius PMA600H Bedienungsanleitung

Sartorius

Sartorius Sartorius PMA 35D-X Betriebsanleitung

Sartorius

Sartorius QC34EDE-S Bedienungsanleitung

Sartorius

Sartorius IS 300 IGG-H Bedienungsanleitung

Sartorius

Sartorius M-prove Series Bedienungsanleitung

Sartorius

Sartorius Cubis MCE32202P Bedienungsanleitung

Sartorius

Sartorius ED224S-0CE Bedienungsanleitung

Sartorius

Sartorius PMA.Evolution Bedienungsanleitung

Sartorius

Sartorius combics 1 Bedienungsanleitung

Sartorius

Sartorius la series Bedienungsanleitung

Sartorius

Sartorius PMA7500 Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung