Satel Integra Series Bedienungsanleitung
Connecting to
BT Redcare Secure Mk3
MANUAL
SATEL sp. z o.o.
ul. Budowlanych 66
80-298 Gdańsk
POLAND
tel. + 48 58 320 94 00
www.satel.eu
redcare_i_en 05/19
Alarm Control Panels
WARNINGS
The security alarm system should be installed by qualified personnel.
Prior to installation, please read carefully this manual in order to avoid mistakes that can lead
to malfunction or even damage to the equipment.
Disconnect power before making any electrical connections.
Changes, modifications or repairs not authorised by the manufacturer shall void your rights
under the warranty.
SATEL's goal is to continually upgrade the quality of its products, which may result in some
changes of their technical specifications and firmware. The current information on
the introduced modifications is available on our website.
Please visit us:
http://www.satel.eu
The declaration of conformity may be consulted at www.satel.eu/ce
The following symbols may be used in this manual:
- note;
- caution.
SATEL 1
CONTENTS
1. General.............................................................................................................................2
2. System installation............................................................................................................2
2.1 Cabling ......................................................................................................................2
2.2 Connection of BT Redcare Secure Mk3 unit .............................................................2
3. System programming........................................................................................................ 3
3.1 Programming communication with BT Redcare Secure Mk3 unit..............................3
SATEL 2
1. General
This manual applies to the control panels of the INTEGRA and INTEGRA Plus series:
– INTEGRA 24
– INTEGRA 32
– INTEGRA 64
– INTEGRA 128
– INTEGRA 64 Plus
– INTEGRA 128 Plus
– INTEGRA 256 Plus
This manual assumes that the dial capture board is already fitted inside the BT Redcare
Secure Mk3 unit.
AUX or another high current output can be used instead of OUT2 in step 2.2.2 if you prefer.
The Redcare terminals marked PANEL A and PANEL B are not polarity conscious.
The dial capture board will auto detect the events as they are sent from the INTEGRA panel.
The Redcare unit takes up to 5 minutes to boot, so the installer must wait before it is online.
2. System installation
Disconnect power before making any electrical connections.
The following tools will be useful during installation:
slotted screwdriver 2.5 mm,
Phillips screwdriver,
side cutters.
2.1 Cabling
It is recommended that unscreened straight-through cable be used for making electric
connections between devices included in the system (using twisted-pair cable, e.g. UTP,
STP, FTP, is not advisable).
2.2 Connection of BT Redcare Secure Mk3 unit
The control panel mainboard contains electronic components sensitive to
electric charges.
You must complete all wiring, connections and device installations before
connecting the battery or applying AC mains to the control panel.
1. Connect the “TIP” and “RING” telephone line input terminals from the INTEGRA panel to
the terminals marked “Panel A” and “Panel B” on the Secure MK3 unit.
2. Connect the “OUT2” high-current programmable output terminal from the INTEGRA panel
to the terminal marked “PWR+” on the Secure MK3 unit.
3. Connect the “COM” common ground terminal adjacent to the “OUT2” terminal from the
INTEGRA panel to the terminal marked “0V” on the Secure MK3 unit.
SATEL 3
Fig. 1. The way to connect BT Redcare Secure Mk3 to an INTEGRA panel.
I – Dial capture module connected to PSTN dialer.
II – High current output connected to Redcare power input.
3. System programming
Connect your computer to an INTEGRA panel for programming using:
DLOADX software (available from Satel website)
PC computer running Windows
USB-RS programming cable
3.1 Programming communication with BT Redcare Secure Mk3 unit
1. Navigate to “Data →Reporting →Monitoring stations” in DLOADX.
2. Click the tick box next to “Reporting – TELEPHONE”.
3. Select “Station 1 only”.
4. Select “Reporting Format: Contact ID (full)”.
5. Enter “29” in “Tel. Number”.
6. Enter the last 4 digits of the Redcare TAID as the identifier. Enter this in both “Identifiers
1” and “Identifiers Sys.”.
7. Navigate to “Data →Outputs”.
8. Program the Output 2 function to “41: Power supply”.
9. Write the changes to the panel.
SATEL 4
Fig. 2. Example of Reporting settings.
SATEL 5
Fig. 3. Example of Outputs settings.
Andere Handbücher für Integra Series
4
Dieses Handbuch passt für folgende Modelle
8
Inhaltsverzeichnis
Andere Satel Bedienfeld Handbücher
Satel
Satel CA-64 PTSA Bedienungsanleitung
Satel
Satel CA10 plus Bedienungsanleitung
Satel
Satel VERSA Series Betriebsanleitung
Satel
Satel Versa Betriebsanleitung
Satel
Satel Versa Plus Bedienungsanleitung
Satel
Satel CA-5 Bedienungsanleitung
Satel
Satel Versa Plus Betriebsanleitung
Satel
Satel INTEGRA Plus Betriebsanleitung
Satel
Satel CA-5 Bedienungsanleitung
Satel
Satel VERSA IP Betriebsanleitung
Satel
Satel CA-5 Bedienungsanleitung
Satel
Satel Integra Series Benutzerhandbuch
Satel
Satel Versa Bedienungsanleitung
Satel
Satel ACCO-NT2 Benutzerhandbuch
Satel
Satel INTEGRA Plus Bedienungsanleitung
Satel
Satel CA-64 PTSA Bedienungs- und Montageanleitung
Satel
Satel VERSA Plus Series Betriebsanleitung
Satel
Satel Integra Plus Series Benutzerhandbuch
Satel
Satel PERFECTA-T Bedienungsanleitung
Satel
Satel INTEGRA Bedienungsanleitung
