SATO CL408e Bedienungsanleitung

SATO CL408e

Internal Rewinder

User’s Manual

SATO America, Inc.

545 Weddell Drive

Sunnyvale, CA 94089

Industrial Bar Code Printers

Proc 72

P/N W00405301

All manuals and user guides at all-guides.com

all-guides.com

SATO CL-408e Internal Rewinder2

STEP PROCEDURE

1. Switch the printer OFF and

disconnect the AC power cord.

2. Raise the access door and

remove (2) screws holding the

side cover to the inside frame.

Figs. 1 & 2

3. Remove (2) screws holding the

side cover to the o tside frame.

Remove the cover to expose the

electronics.

Label Rewinder Kit

SUB FRAME

UNIT

ADJUST PLATE UNIT TIMING BELT

(4) BLADE SPRING

REWIND SHAFT UNIT

SCREW ASSORTMENT

GUIDE FRAME UNIT

SPRING

CABLE STAY

Fig. 1

Steps Before Installation

All manuals and user guides at all-guides.com

SATO CL-408e Internal Rewinder 3

Steps Before Installation

RAISE THE TOP ACCESS

DOOR AND REMOVE (2)

SCREWS HOLDING THE

SIDE COVER TO THE

INSIDE FRAME

REMOVE (2) SCREWS

HOLDING THE SIDE COVER

TO THE OUTSIDE FRAME

ELECTRONICS

COMPARTMENT REMOVE SIDE

COVER

Figs. 2

All manuals and user guides at all-guides.com

SATO CL-408e Internal Rewinder4

TEAR BAR

ATTACH GUIDE FRAME

UNIT WITH SCREWS

IN THREE PLACES

ROUTE CABLE

THROUGH HOLE

IN SIDE WALL

Figs. 3

Internal Rewinder Installation

STEP PROCEDURE

1. Remove (2) screws to detach the tear bar. Retain the screws.

2. Remove and retain screw from nder the front access door latch.

Ro te the cable from the G ide Frame Unit thro gh the hole in

the side wall and sec re nit with (3) screws as shown. Figs. 3

REMOVE SCREW AND

RETAIN FOR THE

GUIDE FRAME UNIT

All manuals and user guides at all-guides.com

SATO CL-408e Internal Rewinder 5

Internal Rewinder Installation

STEP PROCEDURE

3. Remove (4) screws to detach the access plate. Retain the screws. Fig. 4

4. Gently g ide the Rewind Shaft Unit thro gh the access opening. Note the

correct orientation of the bracket on the nit. Attach the rewind shaft nit with

screws previo sly removed from the access plate. Figs. 5 & 6

REMOVE AND

RETAIN (4) SCREWS

ACCESS PLATE

GENTLY GUIDE THE REWIND

SHAFT UNIT THROUGH THE

ACCESS OPENING. NOTE

THE CORRECT ORIENTATION

OF THE BRACKET ON THE

REWIND SHAFT IN THE

ELECTRONICS SIDE

Fig. 4

Fig. 5 ELECTRONICS SIDE

ATTACH THE REWIND

SHAFT UNIT WITH

(4) PREVIOUSLY

REMOVED SCREWS

Fig. 6

All manuals and user guides at all-guides.com

SATO CL-408e Internal Rewinder6

Internal Rewinder Installation

LOOSEN (2)

SCREWS HOLDING

STEPPER MOTOR

AND DETACH BELT

BELT ROUTING

IDLER GEARS

ON SUB FRAME

UNIT

GEAR ON REWIND

SHAFT UNIT

ROUTE THE BELT AROUND IDLER

GEARS ON SUB FRAME UNIT AS

SHOWN. PLACE THE SUB FRAME

UNIT ON THE REWIND SHAFT UNIT

BRACKET. THERE ARE (2)

LOCATING PINS ON THE BRACKET.

SECURE WITH SCREW

LOCATING PINS Fig. 7

Figs. 8

STEP PROCEDURE

5. Loosen (2) screws holding the stepper motor and detach the belt. Fig. 7

6. Attach the s b frame nit to the bracket on the rewind shaft nit. Note the

locating pins. Ro te the timing belt in position as shown, then sec re the

bracket with screw. Figs. 8

All manuals and user guides at all-guides.com

all-guides.com

SATO CL-408e Internal Rewinder 7

Internal Rewinder Installation

ROUTE AND ATTACH THE BELT

FROM THE IDLER GEARS TO

THE STEPPER MOTOR SHAFT.

REATTACH THE MOTOR BELT

PREVIOUSLY REMOVED.

TIGHTEN THE MOTOR MOUTING

SCREWS

ATTACH ADJUST PLATE UNIT

TO THE SURFACE OF SUB

FRAME UNIT WITH (2)

SCREWS AS SHOWN.

BE SURE THE BELT IS

ENGAGED ON THE

GEAR OF THE ADJUST

PLATE UNIT

ADJUSTMENT SCREW -

FOR ADJUSTING BELT

TENSION

ATTACH

SPRING

Fig. 9

Fig. 10

STEP PROCEDURE

7. Ro te and attach the belt from the idler gears to the stepper motor.

Reattach the motor belt previo sly removed. Tighten the motor mo nting

screws. Fig. 9

8. Attach Adj st Plate Unit to the S b Frame Unit with (2) screws. Attach

the tension spring. Adj st the belt tension as necessary with the

adj stment screw. Fig. 10

All manuals and user guides at all-guides.com

SATO CL-408e Internal Rewinder8

Internal Rewinder Installation

Figs. 12

ATTACH (4) BLADE

SPRINGS WITH

SCREWS PROVIDED

ROLL HOLDER

STEP PROCEDURE

9. Attach Cable Stay to frame. Connect the cable from the g ide plate nit

into CN10 on the Main PC Board. Make s re the cable does not to ch the

motor p lley. Figs. 11

10. Attach (4) Blade Springs to spindle with screws provided. Position roll

holder to spindle. Figs. 12

11. Replace the side cover and sec re with screws previo sly removed.

12. Install labels per Figs. 13 & 14.

Figs. 11

ATTACH CABLE STAY TO

FRAME. ROUTE CABLE

FROM GUIDE FRAME UNIT

TO PC BOARD AT CN10

CONNECTOR

All manuals and user guides at all-guides.com

SATO CL-408e Internal Rewinder 9

Internal Rewinder Installation

Fig. 13

LABELS

LABEL ROLL

Figs. 14

PLACE ROLL

HOLDER ON SPINDLE

ATTACH END OF LABEL TO

THE SPINDLE AND SECURE

WITH THE RETAINER. TURN

THE SPINDLE CLOCKWISE

TO TAKE UP SLACK

SHUT OFF SWITCH - IS

ACTIVATED WHEN THE REWIND

SPOOL IS FULL OF LABELS

All manuals and user guides at all-guides.com

Andere Handbücher für CL408e

Inhaltsverzeichnis

Andere SATO Drucker Handbücher

SATO

SATO Argox D4 Series Bedienungsanleitung

SATO

SATO D508 Bedienungsanleitung

SATO

SATO CL608 Bedienungsanleitung

SATO

SATO Argox X-1000VL Bedienungsanleitung

SATO

SATO GL 4xxe Series Kurzanleitung

SATO

SATO Argox CP Series Bedienungsanleitung

SATO

SATO MB2i Series Bedienungsanleitung

SATO

SATO DR308e Bedienungsanleitung

SATO

SATO CG2 Series Bedienungsanleitung

SATO

SATO XL400 Bedienungsanleitung

SATO

SATO E series Betriebsanleitung

SATO

SATO CL608e/CL612e Bedienungsanleitung

SATO

SATO CX208 Bedienungsanleitung

SATO

SATO PW208NX Bedienungsanleitung

SATO

SATO M-84Pro Series Bedienungsanleitung

SATO

SATO CS-9018 Bedienungsanleitung

SATO

SATO MB400I Bedienungsanleitung

SATO

SATO M10e Series Bedienungsanleitung

SATO

SATO Argox iX4-280 Bedienungsanleitung

SATO

SATO CX200TT Installationsanleitung

SATO

SATO CLe RFID Smart Bedienungsanleitung

SATO

SATO CL-408 Bedienungsanleitung

SATO

SATO Argox D4-250 Bedienungsanleitung

SATO

SATO GT408 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung