SATO GL 4xxe Series Kurzanleitung

www.satoamerica.com

LAN/WLAN

Configuration Instructions

For GL4xxe

www.satoamerica.com

Table of Contents

Section Page

1. Wired LAN configuration…………………………………………………… 3

2. Wireless LAN configuration………………………………………………… 5

www.satoamerica.com

1. Configuring LAN connection on GL4xxe

1. Before starting configuration, make sure your printer has the Ethernet interface

card installed and the printer is powered on. (Please note, settings are stored on

the printer, NOT on the interface card like our other model printers).

2. Press the “LINE” key to take the printer offline.

3. Scroll down to “ADVANCE MODE” and press

the “ENTER” key.

4. Scroll up to “Admin User” and press the

“ENTER” key. Highlight the option to

“Enable” and press “ENTER”. If the display

says “Enter Switch Locked”, press the down and

“ENTER” key at the same time to unlock the

menu and then you should be able to press

“ENTER” on “Enable” for Admin User.

5. Press the “FUNCTION” key to bring the menu

up and use the arrow key to select

“INTERFACES” and press the “ENTER” key.

6. If using DHCP, scroll to “ETHERNET

ADDRESS” and press “ENTER”. Select

“DHCP” and make sure it is selected to

“Enabled”. If you want to set up a static address

for the printer, make sure “DHCP” is set to

“Disabled” then scroll to “ETHERNET

ADDRESS” and press “ENTER”. The next

steps will guide you through a static address setup.

www.satoamerica.com

7. Select “IP Address” and press “ENTER”. Press

“ENTER” two more times to start configuring

the first set of numbers for your IP address. Use

the up and down arrows to select your numbers.

After the first set of numbers are configured, use “ENTER” to continue to the

next set of numbers and repeat the process until your IP address is set. Press the

“CANCEL” key 2 times to return to your “ETHERNET ADDRESS” settings.

8. Repeat the above process for your subnet mask and default gateway.

9. When you are finished configuring your IP

Address, Subnet Mask, and Default Gateway,

press the “FUNCTION” key and go back to

“INTERFACES” again.

10. Scroll through the list until you see “Printer

Mgmt.” and press “ENTER”. Select “SNC

PORT” and press “ENTER” again.

11. Make sure your SNC Port is set to “Ethernet”

and press “ENTER”.

12. Press “FUNCTION” again and scroll to

“INTERFACES” and press “ENTER”. Scroll to

“Host Interface” and press “ENTER”. Change

this option to “ETHERNET”.

13. Press the “LINE” key 2 times on your printer

and you will be prompted to press “ENTER” to

save your settings or “CANCEL” to continue

without saving settings.

14. After your settings have been saved, your printer will reboot automatically.

www.satoamerica.com

2. Configuring Wireless LAN connection on GL4xxe

1. Before starting configuration, make sure your printer has the Wireless Ethernet

interface card installed and the printer is powered on. (Please note, settings are

stored on the printer, NOT on the interface card like our other model printers).

2. Press the “LINE” key to take the printer offline.

3. Scroll down to “ADVANCE MODE” and press

the “ENTER” key.

4. Scroll up to “Admin User” and press “ENTER”.

Highlight the option to “Enable” and press

“ENTER”. If the display says “Enter Switch

Locked”, press the down and “ENTER” key at

the same time to unlock the menu and then you

should be able to press “ENTER” on “Enable”

for Admin User.

5. Press the “FUNCTION” key to bring the menu

up and use the arrow key to select

“INTERFACES” and press the “ENTER” key.

6. If using DHCP, scroll to “WLAN ADDRESS”

and press “ENTER”. Select “DHCP” and make

sure it is set to “Enabled”. If you want to set up

a static address for the printer, make sure

“DHCP” is set to “Disabled” then scroll to

“WLAN ADDRESS” and press “ENTER”. The

next steps will guide you through a static

address setup.

www.satoamerica.com

7. Select “IP Address” and press “ENTER”. Press

“ENTER” two more times to start configuring

the first set of numbers for your IP address. Use

the up and down arrows to select your numbers.

After the first set of numbers are configured, use “ENTER” to continue to the

next set of numbers and repeat the process until your IP address is set. Press the

“CANCEL” key 2 times to return to your “ETHERNET ADDRESS” settings.

8. Repeat the above process for your subnet mask and default gateway.

9. When you are finished configuring your IP

Address, Subnet Mask, and Default Gateway,

press the “FUNCTION” key and go back to

“INTERFACES” again.

10. Scroll to “WLAN SETTING” and press the

“ENTER” key. Once in the WLAN SETTING

menu, select “SSID Name” and press “ENTER”

11. Your SSID will be your wireless network name.

The network name can only be entered 15

characters at a time. Select “SSID Name(01-

15)” and press the “ENTER” key. Enter your

SSID name by using the up and down arrows to select your characters to input

and use the right arrow to advance to the next character. If your network name is

more than 15 characters long, you will need to select “SSID Name(16-30)” to

continue with setting up your SSID.

12. If you are NOT using wireless security on your network skip to step 13. If you

are using wireless security, press the “FUNCTION” key to return to the main

menu, scroll to “INTERFACES” and press the “ENTER” key. Scroll down to

“WLAN Setting” and press the “ENTER” key. You now need to find out if your

network is using WEP security or WPA security and if the connection is a shared

or open connection. For “Open” or “Shared”

security, scroll to “Auth Method” and select the

appropriate setting for your network.

www.satoamerica.com

WEP SECURITY SETUP

If you are using WEP Security, scroll to “WEP

Key 1” (or whichever key is set on your

network), and then scroll to “Key Format”. You

will need to select if your WEP key is being

used in “ASCII” format, or in “Hexadecimal”

format.

Next you will select your “Key Width” to 40 or

128 bytes of data.

Afterwards you will set the WEP key Byte by

Byte and press enter when you are done with

each Byte.

WPA SECURITY SETUP (WPA2 Security is not supported by our Interface cards)

If you are setting your security to WPA security,

scroll to “WPA Mode” and press “ENTER”.

Select “Personal” and press “ENTER”

You will then be prompted to choose you’re

“WPA Cipher”. Choose your appropriate

setting for your network weather it is TKIP or

AES.

Next you will be prompted for the first 15

characters of your password. If you have more

than 15 characters to your password, you will

have to select “WPA P-Phs(16-30)” for your

next set of characters.

www.satoamerica.com

13. When you are finished configuring your

wireless security, press the “FUNCTION” key

and go back to “INTERFACES” again.

14. Scroll through the list until you see “Printer

Mgmt.” and press “ENTER”. Select “SNC

PORT” and press “ENTER” again.

15. Make sure your SNC Port is set to “Ethernet”

and press “ENTER”.

16. Press “FUNCTION” again and scroll to

“INTERFACES” and press “ENTER”. Scroll to

“Host Interface” and press “ENTER”. Change

this option to “ETHERNET”.

17. Press the “LINE” key 2 times on your printer

and you will be prompted to press “ENTER” to

save your settings or “CANCEL” to continue

without saving settings.

18. After your settings have been saved, your printer will reboot automatically.

Andere Handbücher für GL 4xxe Series

Inhaltsverzeichnis

Andere SATO Drucker Handbücher

SATO

SATO WS408TT Bedienungsanleitung

SATO

SATO HT200e Bedienungsanleitung

SATO

SATO CX400 Bedienungsanleitung

SATO

SATO CT 400 Bedienungsanleitung

SATO

SATO ARGOX CP-EX Series Bedienungsanleitung

SATO

SATO CT 400 Gebrauchs- und Pflegehandbuch

SATO

SATO M-8459Se Series Bedienungsanleitung

SATO

SATO CL-408 Gebrauchs- und Pflegehandbuch

SATO

SATO M-5900RV Gebrauchs- und Pflegehandbuch

SATO

SATO CL-408 Betriebsanleitung

SATO

SATO M-8400RVe Series Gebrauchs- und Pflegehandbuch

SATO

SATO CX208 Bedienungsanleitung

SATO

SATO M10e Series Bedienungsanleitung

SATO

SATO CL408e Bedienungsanleitung

SATO

SATO WS208 Bedienungsanleitung

SATO

SATO GL4 Series Bedienungsanleitung

SATO

SATO LP 100R L Bedienungsanleitung

SATO

SATO LM408-LM412e Bedienungsanleitung

SATO

SATO GZ4e Series Bedienungsanleitung

SATO

SATO /gt Series Bedienungsanleitung

SATO

SATO M-5900RV Gebrauchs- und Pflegehandbuch

SATO

SATO CL4XXe Referenzhandbuch

SATO

SATO CL408e Bedienungsanleitung

SATO

SATO MB 200i Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung