Savant CLI-W200 Bedienungsanleitung

009-1593-02

SMART THERMOSTAT

QUICK START GUIDE

CLI-W200

2009-1593-02

What’s in the Box

Speciﬁcations

Optional Sensors

(1) Wi-Fi Thermostat (CLI-W200x)

(1) Installation Kit

(2) Drywall Anchors (039-0328-xx)

(2) #6 x 3/4 inch Pan Head Screws (039-0327-xx)

(1) Sheet of Wire Labels (080-0096-xx)

(1) Quick Start Guide (this document)

– SST-TEMP1 Remote Temperature (Flush Mount)

– SST-OTEMP1 Remote Temperature (Outdoor)

– CLI-THFM1 Temperature and Humidity (Flush Mount)

– CLI-PLEN1R/C Plenum Sensor

– CLI-SLAB1 Slab Sensor

Environmental

Temperature 32 to 104 F (0 TO 40 C)

Humidity 10% to 90% (non-condensing)

Power

Input 24V AC

Current Draw 70 mA typical, 250 mA maximum

Max Power 6 watts

Cable Requirements

Power #18 AWG

HVAC #18 AWG Thermostat Wire (solid)

Remote Sensors #24 AWG - 500 feet (152 m) max

Regulatory

Safety / Emissions FCC Part 15

FCC ID: ASU-CLIW200

IC: 10052A-CLIW200

RoHs Compliant

Standards

Wireless Wi-Fi (802.11 b/g/n 2.4 GHz)

IMPORTANT! 802.11r fast roaming

is not supported.

Security 70 mA typical, 250 mA maximum

Max Power 6 watts

009-1593-02

– Pencil

– #2 Phillips screwdriver

– Small slotted screwdriver

– Drill with / inch drill bit

– Wire stripper

– Needle-nose pliers

– Hammer (if wall anchors are used)

Welcome

Getting Started

Location and Mounting Overview

The following is needed for a trouble free installation:

This document describes how to:

1. Remove the old thermostat.

2. Mount your new CLI-W200 thermostat.

3. Wire your new CLI-W200 thermostat.

CAUTION! When replacing an older thermostat that

contains Mercury in a sealed tube, do not discard into trash.

Refer to the thermostat-recycle.org website for information

on how to properly dispose.

For new installations or when relocating the thermostat,

follow the guidelines below:

– Locate thermostat on an inside wall.

– Do not locate where air circulation is poor such as in a

corner or behind a door.

– Do not locate near windows or doors to reduce the expo-

sure to drafts.

– Install away from any heating conditions such as direct

sunlight, near a radiator register or vent, or near a ﬁreplace.

– To adhere to ADA requirements, install thermostat 48 - 54

inches (1.22 - 1.37 meters) above the ﬂoor.

– Height requirements can be adjusted upward to 60 inches

(1.5 meters) if ADA requirements are not mandatory.

– The thermostat does not need to be level to operate cor-

rectly. Leveling the thermostat is for aesthetics only.

– Thermostat can be oriented in either a portrait or land-

scape layout.

4009-1593-02

Remove Old Thermostat

1. Before starting the process, scroll through the old thermo-

stat and record the current settings and schedules.

2. Switch OFF power at either the breaker panel or the

switch that controls your HVAC system.

3. Open the old thermostat so the wiring is accessible. Take

a photo of the existing thermostat and wiring. The photo

should reveal wire colors and terminal designations.

4. Using chart below, add a check and record the wire color

for each power wire. Not all terminals may be populated.

Terminal Color of Wire

5. Remove each of the wires recorded above and attach a

label that matches the terminal designation from the old

thermostat. Label wires according to the terminal desig-

nation and NOT the wire color.

6. Again, using the chart below, add a check and record the

wire color for each signal wire.

Terminal Color of Wire

NOTE: Additional information on terminal designa-

tions and useful wiring diagrams are available in the

CLI-W200 Thermostat Deployment Guide located in

the pages of the Savant Customer Community.

7. With a screwdriver, remove the wires from each terminal.

TIP! Wrap wires around a pencil or similar to prevent

the wires from falling back into wall.

8. Remove the old thermostat from the wall.

009-1593-02

Install Thermostat Mounting Plate

1. To separate the thermostat from its mounting plate, grasp

the mounting plate in one hand and the thermostat in the

other (Grasp the end opposite the proximity sensor).

2. Rock the top and bottom halves until they separate.

3. Position the thermostat mounting plate onto the wall.

With a pencil, mark the two mounting holes onto the wall

(See image above).

– When mounting using a portrait layout, use the bubble

level installed in the center of the mounting plate to

level.

– When mounting using a landscape layout, remove

bubble level by pushing it out through the rear of the

mounting plate and reinstall it into the bubble level slot

on the right side of center cutout. See diagram above.

4. Drill a / inch hole on each mark made and tap the wall

anchor into wall until ﬂush. In some installations that have

a sub wall to fasten to, wall anchors may not be required.

5. Pull the existing wires through the center cutout in the

mounting plate.

6. Screw the mounting plate to the wall using the supplied

#8 x / inch screws.

Bubble level slot

(Portrait)

Bubble level slot

(Landscape)

Pull wires through

the center opening

Install Anchors

into Drywall

#6 x 3/4 inch

screws

Install Anchors

into Drywall

6009-1593-02

Making Connections

Connecting Power

The CLI-W200 does not run on batteries and requires a

separate power source to operate. To power the thermostat, a

voltage must be applied to the RH and 24C terminals.

If only the power wires removed were from the R and C

terminals of the old thermostat (See Remove Old Thermostat

section above), use the diagram below to make connections.

1. With small slotted screw-

driver, turn the screws on

connector counterclock-

wise (CCW) until silver

crimps open enough to

slide wire(s) into square

slots.

< 1/8 inch

bare wire

exposed

2. Strip back insulation on each wire to / inch and insert

the stripped wire into the proper connection.

3. Turn screws clockwise (CW) until the crimps tighten

around each wire. Tug on each wire a bit to verify they

are secure.

When connecting wires to the CLI-W200, follow the guide-

lines set below to ensure a safe and secure connection.

TX+

TX-

24C

RH - Connect the wire

removed from R termi-

nal of old thermostat to

the RH terminal.

On a new install, RH

connects to the 24V

AC wire from the HVAC

transformer.

24C - Connect the wire

removed from the C

(common) terminal on

old thermostat to the

24C terminal.

On a new install,

24C connects to the

common wire from the

HVAC transformer.

009-1593-02

Two Power Source Wiring

TX+

TX-

24C

Power wire (Rc)

from HVAC

cooling.

Common (C)

wire from HVAC.

Power wire (R)

from HVAC

heating.

RH Supplies power to the relays connected to terminals

W1, W2, and O.

RC Supplies power to the relays connected to terminals

Y1, Y2, and G.

24C Common terminal. The common (C) wire from HVAC

system is required for thermostat to run.

Additional Powering Schemes

Jumper Shunt - JP1

If the HVAC system uses separate power sources to run the

heating and cooling, you should have three wires labeled for

power (R, C, and RC). In this scenario, remove the jumper

shunt from JP1. The next section describes this.

Jumper JP1 on the thermostat board connects the RH and RC

terminals. The thermostat is shipped from the factory with a

jumper shunt installed. For systems with more than one power

source, remove the jumper shunt.

REMOVE SHUNT

24C

JP1

Powers Relays

W1, W2, and O.

Powers Relays

Y1, Y2, and G.

IMPORTANT! Remove

jumper shunt from JP1

if more than one power

source is used. Failure

to remove the shunt will

result in damage to the

thermostat.

8009-1593-02

HVAC Wiring

Temperature Sensors

Use the table below to connect the signaling wires from the

HVAC system. Depending on the type of system installed in

your home will determine which wires are connected. In some

installations, only the power wires described in the previous

sections are required.

There are connections for two temperature sensors.

–RS1 - The main temperature sensor. This sensor is shipped

already pre-installed between terminals RS1 and GND

–RS2 - A remote temperature sensor can be added between

terminals RS2 and GND. No polarity is observed on either

sensor.

TIP! Refer to the Making Connections section above to

ensure a safe and secure connection is made.

O Relay to control changeover valve on a Heat Pump

G Fan Relay

Y2 Relay for control of 2nd stage cooling

Y1 Relay for control of 1st stage cooling

W2 Relay for control of 2nd stage heating

W1 Relay for control of 1st stage heating

AUX OUT

AUX IN

RS2

RS1

GND

RX-

RX+

GND

1-WIRE

5V DC

Remote Sensor

(RS2)

009-1593-02

Network and Conﬁguration Requirements

Network Conﬁguration

Additional Information

Smart Sensor Connection

A 1-wire humidity/temperature (CLI-THFM1) sensor that sup-

ports measuring both humidity and temperature can also be

added to the system. Connect the sensor to the 1-Wire, 5V DC,

and GND terminals as shown in diagram below.

With the thermostat installed and wired, it can now be added

to the local network and once communicating with the Savant

Pro System Host an HVAC conﬁguration can be created and

uploaded to the Host. Locate the CLI-W200 Thermostat De-

ployment Guide available on the Savant Customer Communi-

ty to ﬁnish installation of the thermostat.

To ensure the IP Address will not change due to a power

outage, Savant recommends DHCP reservation be conﬁgured.

Using this method, static IP Addresses for all devices can be

managed from a single User Interface, avoiding the need to

access devices individually.

Setting DHCP reservation varies from router to router. Refer

to the documentation for the router to conﬁgure DHCP

reservation.

– CLI-W200 Thermostat Deployment Guide (009-1636)

– SST-TEMP1 Remote Indoor Temp Sensor QRG (009-0800)

– SST-OTEMP Remote Outdoor Temp Sensor QRG (009-0989)

– CLI-THFM1-xx Temp and Humidity Sensor QRG (009-1064)

– CLI-SLAB1 Slab Sensor QRG (009-1097)

– CLI-PLEN1R Residential Plenum Sensor (009-1096)

– CLI-PLEN1C Commercial Plenum Sensor (009-1100)

AUX OUT

AUX IN

RS2

RS1

GND

RX-

RX+

GND

1-WIRE

5V DC

Remote 1-Wire

Sensor

10009-1593-02

Frequently Asked Questions

Does the CLI-W200 require batteries?

No, the CLI-W200 is powered using the power from the HVAC

system. If no common (C) wire was removed from the old

thermostat, a common wire must be added.

How does CLI-W200 get software updates?

Software is updated Over The Air (OTA). Whenever an update

is available on the Savant Cloud, the update will take place

automatically. The CLI-W200 must be connected to a local

network that has WAN access for the updates to occur.

Will CLI-W200 still work if the Wi-Fi connection is lost?

Yes, most thermostat functions will still function when not

connected to Wi-Fi. However, functions such as schedules and

OTA updates can not occur.

Are both Fahrenheit and Celsius supported?

Yes

Does the thermostat support setting both a heating and

cooling set point?

No, The CLI-W200 thermostat is a single set point thermo-

stat. However, the thermostat does support adding a +/-

range to the set point. For example, adjusting the set point to

70° with a range of +/- 3° will manage the temperature so it

stays between 67° and 73°.

Does the thermostat support measuring humidity?

Yes, Savant oers a 1-wire smart sensor (CLI-THFM1) that

measures both humidity and temperature.

My thermostat was received damaged. What should I do?

If the thermostat was purchased through a contractor or

retailer, contact the contractor or retailer to return it. If ther-

mostat was purchased from the Savant Store, contact Savant

through the Savant Customer Community.

Inhaltsverzeichnis

Andere Savant Thermostat Handbücher

Savant

Savant CLI-8000 Bedienungsanleitung

Savant

Savant CLI-W210 Kurzanleitung

Savant

Savant SST-W100 Bedienungsanleitung

Savant

Savant CLI-W210 Bedienungsanleitung

Savant

Savant SST-W100 Bedienungsanleitung

Savant

Savant CLI-W210 01 Series Bedienungsanleitung

Savant

Savant SST-W100 Bedienungsanleitung

Savant

Savant SST-W100 Kurzanleitung

Savant

Savant GE SST-W300 Bedienungsanleitung

Savant

Savant GE SST-W300 Kurzanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung