Savant ITP-E8000 Series Bedienungsanleitung

ITP-E8000x | 009-1522-04 | 191009 1 of 2 45 Perseverance Way, Hyannis, MA 02601

Savant® Touch 8 Inch Control Screen (ITP-E8000x-xx) Quick Reference Guide

Box Contents

(1) Savant 8.0 inch In-Wall Touch Screen (ITP-E8000x-xx)

(1) Installation Kit (075-0203-xx)

(1) Installation Template (009-1561-xx)

(1) Mounting Bracket (For standard 2-gang electrical box)

(4) Mounting Bracket Screws (⁄ x 1 in.)

(1) Savant Touch 8 Inch Control Screen Quick Reference Guide

(009-1522-xx)

Environmental

Temperature 32° to 104° F (0° to 40° C)

Humidity 10% to 90% Relative Humidity (non-condensing)

Dimensions

Viewing Image

(IPS) 8.0 in (203.0mm)

Resolution 1280 X 800 | 16.7M colors

Height 5.84 in (148.4 mm)

Width 8.80 in (223.5 mm)

Depth (overall) 1.43 in (36.3 mm)

Depth

(mounting) 0.62 in (15.8 mm)

Weight 0.95 lb (0.44 kg)

Power

PoE 802.3af compliant

Power

consumption

Average

5.14W

Maximum

6.76W

Minimum Supported Release

Savant OS da Vinci 8.10.1

Regulatory

Safety and

Emissions

CE FCC Part 15 WEEE

RoHS Compliant

Speciﬁcations

Network Requirements

Savant requires the use of business class/commercial grade network

equipment throughout the network to ensure the reliability of commu-

nication between devices. These higher quality components also allow

for more accurate troubleshooting when needed.

Connect all Savant devices to the same local area network (LAN) or

subnet as the Host. Savant recommends not implementing any type of

trac or packet shaping in your network topology for Savant devices,

as this may interfere with performance.

Network Changes

If the IP addressing range has changed for the local network, Savant

recommends rebooting the device via the Settings menu to refresh the

network connection and ensure optimal communication:

Navigate from the Home Screen Rooms > Select Location > Settings

> Reboot

Front Panel

Rear Panel

Proximity

Sensor

Mounted on the front of the panel, the proximity

sensor will wake up the screen when motion is

detected in the area.

Micro USB Not Used

Embedded

Speaker

Primarily used for entry service intercom fea-

ture.

Mounting

Slots

Align the mounting fram hooks and press down

to seat. Refer to the Mounting section on Page

Alternative

Power Input Not Used

Link LED Solid Orange - Link is established.

O – No link established

Link Activity

LED

Green Blinking - Indicates data activity.

O – No Activity

Ethernet

8-pin RJ-45 port:

10/100/1000 Base-T auto-negotiating port with

link and activity LEDs

Captive

Screws

Used to secure touch panel to bracket after

mounting frame hooks have been seated. Refer

to the Mounting section on page 2 for details.

Embedded

Microphone

Primarily used for entry service intercom fea-

ture.

Network Conﬁguration

To ensure that the IP address will not change due to a power outage,

a static IP address or DHCP reservation should be conﬁgured. Savant

recommends using DHCP reservation within the router. By using this

method, IP addresses for all devices can be managed from a single UI

avoiding the need to access devices individually.

Setting DHCP reservation varies from router to router. Refer to the

documentation for the router to conﬁgure DHCP reservation.

ITP-E8000x | 009-1522-04 | 191009 2 of 2 45 Perseverance Way, Hyannis, MA 02601

Supported Orientations

Landscape – The ITP touch panel must be installed with the proximity

sensor position on the right hand side.

Portrait – The ITP touch panel must be installed with the proximity

sensor at the top.

Mount the Bracket

The Savant In-Wall Touch Panel is designed to be mounted using either

a standard 2-gang electrical box or low voltage 2-gang bracket.

1. Mount a 2-gang standard electrical box or low voltage bracket to

an existing wall. Recommended height to center of box is between

57 and 65 inches (145 – 165 cm) above a ﬁnished ﬂoor.

2. Secure the mounting bracket to the electrical box/bracket using

the four ⁄ x 1 inch screws provided. Position the touch panel with

mounting tabs facing outward.

NOTE: If the Touch Panel is going to be installed with a Portrait ori-

entation, the electrical box or bracket will need to be rotated

90°.

Apply Power

The ITP-E8000 touch panel is powered using PoE via Cat 5e/6/7 Eth-

ernet cable. Connect one end of the Ethernet cable to a PoE-enabled

network switch or router, and the other end to the data connection on

the back of the ITP. Once the connection is made, the ITP will be pow-

ered on, and an IP address will be automatically assigned via DHCP.

Once the ITP is powered and an IP address has been assigned, the

touch panel can be added to a RacePoint Blueprint® conﬁguration.

For details, refer to the Savant In-Wall Touch Panel Deployment Guide

(009-1475-xx), available on the Savant Customer Community.

Make Connections

Connect a Cat 5e/6/7 Ethernet cable (T568A, T568B) to the RJ-45

LAN/PoE port on rear of touch panel. See image below.

IMPORTANT NOTE!

If a PoE network router is not available, a PoE network injector can be

used.

Secure Panel to Bracket

Once cables are connected to the rear of touch panel, the panel can

be secured to the mounting bracket installed earlier.

1. Loosen the captive screws on the bottom of the touch panel a few

turns to allow the panel to slide into the mounting bracket.

2. Align the mounting frame hooks with the mounting slots.

3. Gently pull down the unit to seat the mounting frame hooks.

4. Tighten the two captive screws to secure the touch panel to the

mounting bracket.

Additional Information

– Savant In-Wall Touch Screen Deployment Guide (009-1475-xx)

– For further product information, visit http://dealers.savantav.com/

portal/redirector.php?id=1268 or scan the QR code below:

Local

Network

To LAN/PoE Port

(RJ-45)

To Router

(PoE)

2-Gang Electrical Box 2-Gang Low Voltage

Bracket

Mounting

Bracket

Tabs Face

Outward

Andere Savant Touchscreen Handbücher

Savant

Savant Wally Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung