Saveo Scan R11D-BH Bedienungsanleitung

Getting Started

Power Switch

Power switch is located on the

underside of the scanner.

On the underside of the scanner you will nd a small recessed

button.

Use a pen or paper clip to push the button until you hear a

notication sound.

Ensure power switch remains depressed after you release it.

Power on Saveo Scan

Switch on and Charge your Scanner

Please switch on your scanner (as illustrated) and place it in the

cradle to charge for 3~4 hours before rst use.

If you want to charge smartphone and scanner simultaneously,

please switch scanner to “Charge Mode” before placing it in the

cradle.

*Please remove the protective sticker from window

before use

Trigger/Power

On button

Wrist Strap

Universal Holder

Exit Window

Operating Elements

LED indicator

Charging Cradle

Switch for Operation Mode

and Charge Mode/Bluetooth

Mode

Micro USB Cable

Use Micro USB cable to connect

to smartphone/tablet

SAVEO-SCAN-R11D-BH

Extend retractable

arm

Press button and slide

outwards to extend the

arm

Attaching your smartphone to scanner using the

universal holder

Extend the retractable arm before placing phone in holder and

then pushing it rmly back against the phone.

Secure phone in

holder

Insert phone

Attach your smartphone

12 3

Connect phone to scanner with Micro USB

As USB connection locations vary on dierent models of

smartphone, the cable can be congured for your specic

model. For iOS devices, please attach the appropriate

adapter to connect to your device.

Connecting via USB OTG

Switch scanner to Operation Mode (Data trans-

mission via USB OTG)

Switch to left:

Operation Mode/

Data transmission

Conrm scanner is connected

Saveo Scan is detected by your smartphone as an external

keyboard. A message will appear on screen to notify you that a

USB device has been connected.

You are now connected. Start scanning.

Scan the Wired USB OTG Communication

barcodes below

Demo

%W%I%R

Demo

%E%R%A

Connecting via Bluetooth

Enable Bluetooth on your device

Go to your phone’s homescreen and nd “Settings”, then

“Bluetooth” and turn Bluetooth on.

Switch scanner to Charge Mode/Bluetooth Mode

Scan the Wireless BT Communication barcodes

below

Demo

%W%L%T

When Bluetooth is enabled, the LED will remain red until the

scanner has been paired with a Bluetooth device.

Switch to right:

Charge Mode/

Bluetooth

Mode

Demo

%E%R%A

Scan Bluetooth Prole Barcodes below

After you scan the Bluetooth prole barcodes below, your

scanner will become visible to Bluetooth enabled devices within

range.

Demo

%H%I%D

HID Prole

Demo

%B%R%C

Search for devices

Your phone will automatically search for devices, Saveo Scan will

appear as an external keyboard with a unique identier number

(R-xxxxxx).

Select R-xxxxxx

to connect

Please note: devices only need to be paired once. When they are within

Bluetooth range they will automatically attempt to connect to each other. If

you wish to pair to another device it is recommended you rst unpair this

device.

You are now connected. Start scanning.

4 5 6

Please note: The scanner should only be paired with one device

at a time. Before you pair your scanner to another device, please

rst unpair it from the device in use. Otherwise it will appear on

your list of “Available Devices” but will not connect. In this case,

please refer to “Unpairing your device” in this guide.

Select scanner from “Available

Devices”and wait for pairing

process to complete.

Devices are now

paired

Once “Connected” is

displayed, your device is

paired to the scanner. Your

scanner is now ready to use.

There are two operating modes on the scanner, Data transmis-

sion mode and Data Storage Mode.

Scan the appropriate barcodes when switching between these

two modes.

Please note: Switching between modes will wipe the scanner’s

internal memory.

Operating Modes

Data Transmission Mode (Default)

Our Default setting is Data Transmission mode. In this mode data

will be sent to smartphone/tablet directly.

To enter Data Transmission Mode please scan the follwing

barcodes.

Demo

%E%R%A

Demo

%M%A%F

Enter Data Transmission Mode

Green/Orange LED ashes followed by 3 beeps.

Demo

%M%A%N

Data Storage Mode

In this mode, data will be saved directly to scanner’s memory.

Scan Transmit Memory Data to receive data stored on scanner’s

internal memory.

Enter Data Storage Mode

Green/Orange LED ashes followed by 3 beeps.

Demo

%E%R%A

To enter Data Storage Mode please scan the follwing barcodes.

Demo

%E%R%A

Clean Memory Data

Green/Orange LED ashes

followed by 3 beeps.

Demo

%R%E%C

Transmit Memory Data

Green/Orange LED ashes

followed by 3 beeps.

Transmit Memory Data

Scan the following barcode to receive data stored in the

scanner’s internal memory..

After data is transmitted to your device it remains on the

scanner’s internal memory. Scan the following barcode to clear

the memory if you do not wish to send this data again.

When the battery power is too low, the Orange LED will ash

and beep once. Scanner should be charged immediately. If

scanner shuts down it is recommended to charge it fully then

power it back on.

Under power-saving mode, there will not be an LED

indication when charging.

Orange LED ON Full charged

Orange LED (Flashing) Charging / Low battery

Red LED ON Oine / Out of Range

Green LED ON Good read

Orange LED ON Good read (Batch mode)

LED Indicator Information

LED Indicator

Reset to Defaults

Reset Conguration to Defaults (scan from A1to A6)

HID Prole

Demo

Current Battery Level

Scan to receive the current

battery level

Scan the following barcode to send battery level information

to your device. The format is outlined in the table below.

%^4^% 80% - 100%

%^3^% 55% - 80%

%^2^% 30% - 55%

%^1^% 10% - 30%

%^0^% under 10%

Battery Level Status

7 8 9

Demo

! " # $%&

Demo

! " # $%&

Demo

!" #

Demo

!" #

Demo

! " # $%&

Demo

%D%F%T

Power saving mode is enabled by default and will put the

scanner to sleep after 1 minutes inactivity. To wake up the

scanner press the trigger.

Demo

%P%D%T00

Disable

Scan to disable power saving

mode

Demo

%P%D%T01

Below are the barcodes to disable/enable power saving mode.

Power Saving ModeTransmission Speed

Transmission speed is dependent on your device. In order not to

lose data please choose the correct speed. Mid Speed is the

default.

Mid Speed

Transmission

(Default)

High Speed

Transmission

Low Speed

Transmission

Demo

%B%T%H

Demo

%B%T%L

Before connecting the scanner to another device it is

recommended you rst unpair from the current device.

Go to the Bluetooth menu on your phone and select the

option menu for scanner from list of paired devices.

Choose “Forget this Device”/”Unpair”

Unpairing your device

1 Minute

Enter Power Saving Mode

after 1 minutes inactivity

5 Minute

Enter Power Saving Mode

after 5 minutes inactivity

15 Minute

Enter Power Saving Mode

after 15 minutes inactivity

30 Minute

Enter Power Saving Mode

after 30 minutes inactivity

Sound Settings

Scan the barcodes below in order (A1 - A2, B1 - B2) to select

whether or not the decoder issues a beep signal after a good

decode. If selecting Do Not Beep after Good Decode, beeper

signals are issued during parameter menu scanning and to

indicate errors.

Beep after good

decode

Do not beep after

good decode

10 11 12

Demo

+%-$.2

Demo

+%-$.4

Demo

+%-$.2

Demo

+%-$.4

Andere Saveo Scan Barcode-Lesegerät Handbücher

Saveo Scan

Saveo Scan M12D-BH Bedienungsanleitung

Saveo Scan

Saveo Scan RCCD-H Bedienungsanleitung

Saveo Scan

Saveo Scan M12D-H Bedienungsanleitung

Saveo Scan

Saveo Scan SAVEO-RNG-G2 Bedienungsanleitung

Saveo Scan

Saveo Scan SAVEO-SCAN-R11D-BH Bedienungsanleitung

Saveo Scan

Saveo Scan M22D-BH Bedienungsanleitung

Saveo Scan

Saveo Scan SAVEO-SCAN-M12D-H Bedienungsanleitung

Saveo Scan

Saveo Scan SAVEO-SCAN-M22D-H Bedienungsanleitung

Saveo Scan

Saveo Scan SAVEO-RV2-Z12D Bedienungsanleitung

Saveo Scan

Saveo Scan SAVEO-RV2-RCCD Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung