Savi MINI MEL P Bedienungsanleitung

INSTALLATION AND USERS GUIDE

IMPORTANT NOTICE - ATTENTION INSTALLER: This Installation and

Users Guide contains important information about the installation,

operation and safe use of this swimming pool/spa light. This Guide

should be given to the owner and/or operator of this equipment.

IMPORTANT WARNING & SAFETY INSTRUCTIONS

DANGER - SERIOUS BODILY INJURY OR DEATH CAN RESULT IF THESE

LIGHTS ARE NOT INSTALLED AND USED CORRECTLY

DANGER - INSTALLERS, POOL OPERATORS AND POOL OWNERS MUST

READ THESE WARNINGS AND ALL INSTRUCTIONS BEFORE USING

THESE LIGHTS

WARNING - Before installing this product, read and follow all warning

notices and instructions in this Guide. Failure to follow warnings and

instructions can result in severe injury, death or property damage. For

more information contact company at numbers contained within Guide.

WARNING - These underwater swimming pool lights MUST BE installed by a

licensed or certified electrician or a qualified pool professional in accordance with

the National Electric Code (NEC) or the Canadian Electric Code (CEC), CSA C22.1.

All applicable local installation codes and ordinances must also be adhered to.

Improper installation will create an electrical hazard which could result in death or

serious injury to pool users, installers or others due to electrical shock.

ALWAYS DISCONNECT THE POWER TO THE POOL LIGHT(S) BEFORE SERVICING.

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Products in this Guide are covered

under one or more of the following

patents: 6,827,464 7,244,037 6,971,760

5,617,496 5,617,497 5,789,471

5,528,714 5,33,228 6,200,012

6,48,952 6,422,730 6,367,100

6,398,397 6,393,192 6,375,342

7,204,602 7,229,027

The following are registered

trademarks and designs of

Zodiac Pool Systems: Savi,

Endglow, Sideglow Oasis

9400 Southridge Park Ct #200 Orlando FL 32819

Tel: 407.855.5630 Fax: 407.210.8679

savilights.com

FOR INDEPENDENT USE OR

WITH PENTAIR CONTROLS or ZODIAC 1 Touch Rev T.1 CONTROLS

WARNING: DO NOT USE IN JUNCTION WITH ANY PENTAIR LIGHT -

THEY WILL NOT HOLD SYNCH ON COLOR SHOWS PAST A FEW HOURS

MINI MEL'S - SAVI MELODY & SOL (COLOR)-"P" SERIES

11.2014

MINI MEL P,MELODY P & SOL P SERIES

Underwater LED Lights

READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY

CAUTION! SAFETY PRECAUTIONS

TURN OFF MAIN POWER TO LIGHT BEFORE INSTALLATION /SERVICE

SAVI Lights are a low voltage light and should NEVER be electrically

connected to a power source other than an approved pool “Safety Rated”

UL Listed outdooor rated Class 3,12VAC Transformer. Failure to comply

will either damage or destroy SAVI Lights and VOID the Warranty.

STEP 1

The light must be installed in or on a wall of the pool (or

water feature) with the top of the lens opening not less than 4

inches (10.16cm) below the normal water level of the pool.

STEP 2

Snake the 2-conductor electric cord through the conduit outlet

of the wall into the conduit and up to the location of

the

12VAC pool transformer. Cut off excess cord after allowing

for

service and length of run to the transformer. Pull the snug

to the wall

STEP 3

Using enclosed Lens Key, thread the light into the wall fitting until it is

snug. Please provide Pool Owner with minimum of 1 key upon job

completetion (see winterization clause above)

NOTE: Requires the use of a 1-1/2” threaded wall fitting.

Product Names WATTS AMPS MINIMUM CONDUIT

REQUIREMENTS

14 1.2

28 2.3

SAVI-MELODY P

SAVI SOL P

NOTE: Make sure all protective coverings have been removed.

An example of an approved pool transformer is the Intermatic model PX-100 or PX-300.

Refer to WIRE GAUGE AND WIRE LENGTH guide for for proper wire gauge size in

reference to the use of Junction Boxes installations. NOTE: SAVI Lights can be used

with any UL Listed outdoor rated Class 3, 12VAC transformer provided the wattage and

amperage is not exceeded by the total wattage and amperage in use.

9400 SOUTHRIDGE PARK COURT SUITE 200 ORLANDO, FLORIDA 32819 USA

Tel: 407.855.5630 Fax: 407.210.8679 savilights.com

4” MIN. FROM WATER

LEVEL TO TOP OF LENS

1.5” Pipe1” min. Pipe

Sweeps ONLY

No 90 degree bends

4” MIN. FROM WATER

LEVEL TO TOP OF LENS

12VAC Pool Transformer

Allow 18” - 24”

slack for

Service Loop

Conduit to 12VAC transformer

Tighten

NOTE: Service

Loop not applicable

for Junction Box

Installations.

1.5” THREADED WALL FITTING

1.5” Pipe through bond beam for a minimum of 14” then 1” conduit

min. with sweeps / no 90 degree bends. We highly recommend

the use of 1.5" pipe throughout the entire width of the bond beam.

NOTE: Use of 1.5” pipe with 14” min. length will accommodate all

SAVI Lighting nicheless products. See Minimum Conduit

Lengths listed above.

Small Gasket

Large Gasket

Flat Gasket

NOTE: For Vinyl wall Fittings use both rubber

gaskets. For Gunite and Fiberglass remove

the Small gasket and use the Large one only.

4” MIN. FROM WATER

LEVEL TO TOP OF LENS

Vertical Installation for

Benches, Swimouts and

Fountains

NOTE: No separate ground or bonding wire is required for the

Melody, SOL low voltage lights which have no exposed metal.

They do not require a niche.

For Replacement LED Light Cartridges

see Light Cartridge Replacement Page

14"

All products listed above come in a variety of cord length

Typical Lengths are: 30-50-100 & 150FT

18"-24" of excess cord recommended as service loop.

LIGHTS ARE SERVICABLE - DO NOT

REMOVE ENCLOSURE/CORD FROM CONDUIT

NOTE: Check with Local Building officials as to what conduit/pipe is acceptable

INSTALLATION INSTRUCTIONS

SERVICABLE PRODUCT

"P" SERIES LED LIGHTS

MINI MEL P 6 .5 3"

NOTE: When using a 1 1/2"MIP fitting on the back

of a SP-1022 or SP-1408 Wall Fitting - SAVI has

experienced that SPEARS MIP's interior is too small

for use with SAVI lights.

11.2014

OPERATION INSTRUCTIONS -INDEPENDENT USAGE

Operational Process for P SERIES LED Color Pool and Spa Lights

Important Note: All xtures must be tied into the same transformer, circuit or switch for synchronization

POWERING ON THE P SERIES LED LIGHTS

1. Turnthelightsonandwaitfor20seconds.Thelightswillfirst comeonwhitefor a few secondsandthenreturntothe

colormodeitwasonpriortobeingturnedoff.(Ifthisistheinitialinstallation,thelightswillreturntowhatevermode

they were in when last receiving power).

2.Tomove to another colormode,Cycle the lights OFF/ON the selected number of times listed below.

Example:IfyouarenowonBLUE (8)andwantthelightstobeMagenta (12),thenthelightsmustbe

turnedoffandon(12)twelvetimestobringyoutoMagenta.

1. Old School - cycles through white,magenta,blue & green colors

2. Dance Mode: Rapid color changes

3. Smooth Mode: slow color transitions

4. Island Mode: Transitions beteen variety of blue and greens

5. USA Mode: Red,white and blue

6. Desert Mode:oranges, reds and magenta

7. Rich Mode: darker color shades

8. Blue

9. Green

3.Thelightshavememory.Ifthelightsareofffor5-10seconds,thenexttimethelightsareturnedon,theywill goto

whiteforapproximatelya fewsecondsandthenreturntothelastcolormodetheywereonpriortobeingturned off

(Step1listedabove).Thisfunctionallowsyoutokeepyourlightsreturningtoyourfavoritecolormodeeverytime

the lights are turned back on.

10. Red

11. White

12. Magenta

13. Save: Saves the current color choice during a color show - see special section on SAVE usage

14. Bring Back: Turns on last saved color selection selected in Postion #13

WHEN OPERATED FROM WALL SWITCH OR OTHER MANUAL ON/OFF METHOD

WARNING!! During the ON/OFF cycle, before the selected mode is displayed, no illumination will

occur. During this period of time the pool/spa will be dark and precautions should be taken to avoid

unforeseen accidents. Failure to observe this warning may result in serious injury for death to pool/spa users.

P Series LED Colored Nicheless Lights are specifically designed to be operated by selected Pentair Controls

and Zodiac Rev T.1 Controls for direct switching/access to colors and programs WITHOUT having to toggle

sequences of ON/OFF. Please refer to Pentair and Zodiac Series controls for Installation and Operational

directions.

Note: When using the above mentioned controls - when programming the Light Function - the general

selection choice offered that should be selected is - INTELLIBRITE. The color and show names will be

slightly different but all operations will be correct.

NOTE: At NO TIME shall the P Series lights be used in conjunction with any other lights - including Savi

standard LED nicheless lights. The color choices, shows and operations are entirely different

These 2 Modes are specifically used with advanced control systems and not Manual Operations

To move to Old School - turn OFF/ON 1 Time.

9400 SOUTHRIDGE PARK COURT SUITE 200 ORLANDO, FLORIDA 32819 USA

Tel: 407.855.5630 Fax: 407.210.8679 savilights.com

11.2014

IMPORTANT: READ FIRST

SAVI LED UNDERWATER LIGHTS ARE LOW VOLTAGE FIXTURES. IMPROPER

WIRE GAUGE AND WIRE LENGTH CAN AFFECT THE PERFOMANCE OF THESE

PRODUCTS. FOLLOW THE GUIDES BELOW TO DETERMINE THE PROPER

OPERATION AND OPTIMUM PERFORMANCE OF SAVI LIGHTS.

WIRE GAUGE & WIRE LENGTH GUIDE

JUNCTION BOX

Black Hot Line

Crimp Style Connectors

Recommended

Crimp Style Connectors

Recommended

BLK BLK

WHT WHT

White Neutral

Green Ground

LOW VOLTAGE (12VAC) TRANSFORMER

PX100 or PX300

NOTE: This Diagram is to be used as a guide line only for a typical System Installation and should only be used

as such. It is the Installers sole responsibility to verify and assure that proper gauging of secondary wiring

from the Transformer to the J-Box are in compliance with your local, State and National Electrical Codes.

JBT

JUNCTION BOX

BUS BAR

PX100 / PX300 MAX WATTAGE

MAX WATTAGE

0-50ft 100ft cord 168W

12GA

12V

JBT 100ft 50ft cord 126W

10GA

12V

JBT 130ft 20ft cord 98W

8GA

12V

JBT

JUNCTION BOX

BUS BAR

PX100 / PX300

0 - 50ft 100ft cord 210W

12GA

13V

JBT 51 - 100ft 50ft cord 168W

10GA

13V

JBT 101 - 125ft 10ft cord 154W

8GA

13V

JBT

JUNCTION BOX

BUS BAR

PX300 ONLY

0-50ft 100ft cord 240W

12GA

14V

JBT 51 - 100ft 50ft cord 224W

10GA

14V

JBT 101 - 125ft 10ft cord 196W

8GA

14V

NOTE: The use of Solid Core over Stranded wire and terminating at Bus Bars is strongly recommended.

NOTE: Min. 12VAC: / Max 13VAC. The maximum run of service between transformer and lights should not

exceed 150ft in total length, inclusive of the use of J Box or not.

9400 SOUTHRIDGE PARK COURT SUITE 200 ORLANDO, FLORIDA 32819 USA

Tel: 407.855.5630 Fax: 407.210.8679 savilights.com

11.2014

JBT

JUNCTION BOX

BUS BAR

PX100 / PX300 MAX WATTAGE

MAX WATTAGE

0-50ft 100ft cord 168W

12GA

12V

JBT 100ft 50ft cord 126W

10GA

12V

JBT 140ft 10ft cord 98W

8GA

12V

JBT

JUNCTION BOX

BUS BAR

PX100 / PX300

0 - 50ft 100ft cord 210W

12GA

13V

JBT 100ft 50ft cord 168W

10GA

13V

JBT 130ft 20ft cord 136W

8GA

13V

JBT

JUNCTION BOX

BUS BAR

PX300 ONLY

0-50ft 100ft cord 240W

12GA

14V

JBT 100ft 50ft cord 224W

10GA

14V

JBT 130ft 20ft cord 182W

8GA

14V

NOTE: Please use appropriate low voltage supply to pool lights, ie. if 12V is appropriate voltage DO NOT

use 13V or 14V tap on transformer output (if so equipped),

WARNING - DO NOT run 120V and Low Voltage wires in the same conduit or enclosures.

ALL Savi LED Colored Lights including Savi Color LED Light Drivers are designed to work or synchronize with

each other. Please follow all installations for proper installation and follow Sychronization Instructions for

proper operation. P Series will only work with other P Series Lights

All Savi White LED Lights and White LED Drivers are designed to allow for the option of dimming or light

output reduction. See enclosed information regarding general guidelines for dimming of our Savi LED

White Lights.

9400 SOUTHRIDGE PARK COURT SUITE 200 ORLANDO, FLORIDA 32819 USA

Tel: 407.855.5630 Fax: 407.210.8679 savilights.com

11.2014

Black Hot Line

Crimp Style Connectors

Recommended

Crimp Style Connectors

Recommended

BLK BLK

WHT WHT

White Neutral

Green Ground

LOW VOLTAGE TRANSFORMER

PX100 or PX300

THE FOLLOWING INFORMATION IS FOR GENERAL INSTALLATION OF DIMMING SWITCHS OR CONTROLS FOR

USE WITH SAVI BLANCO, BLANCO PRO WHITE LED LIGHTS. THIS INCLUDES BLANCO PRO WHITE LED LIGHT

DRIVERS.

All WHITE LED Savi Lights can be dimmed by the use of simplistic dimming switches. These directions specify those switches

that are for independent or stand a lone use. For achieving dimming by the use of automatic or home based energy control

systems please consult those controls systems instructions. AT NO TIME SHALL ANY SWITCH OR CONTROL BE

INSTALLED ON THE 12V SIDE OF THE TRANSFORMER IN AN ATTEMPT TO DIM LIGHTS. DOING SO MAY DAMAGE

THE LED LIGHT CARTRIDGE AND VOID WARRANTY.

White Neutral

Black Hot Line

Dimmer Switch installed in

proper electrical enclosure

DESIGNER LENS SERIES OPTION:

Savi Pool & Spa has created a unique set of options for our LED Series of lights - designer lens. Each one has

the ability to create fantastic lighting effects within the pools interior. No other company can offer these lighting

effects. These are so unique that we have a Patent Pending on this series. Look below and see if any one fits

into your pool environment. Keep in mind that these lenses can be added on to any of our 2013 LED Lights -

even if they have already been installed.

HALF DOME - This escutcheon adds over the existing lens to allow you to

direct 1/2 the light in a direction you want. Downwards-to light a pools

interior without light shining upwards. Upwards to light a waterfeature or

sideways to put light where it might be needed but no where else

HALO LENS - This lens allows for gentle lighting in an area but knocks down

the center beam. This allows for installation on walls, etc where there might be

an opposite wall, etc where you want to eliminate generating a "hot" spot.

Great general lighting but softly.

SPOT LENS - Just the opposite of the Halo whereas we knock down the general

lighting and focus more of the light forwards. Great for illuminating that special

feature.

CATS EYE - This lens reduces the light eminating but for just a "slice" of light

that is broad but thin. An incredible effect for illuminating but without spilling

light all over.

DIAMOND - WOW want to really create something special? The Diamond lens

creates incredible points of light throughout the interior. The points will be

different the farther away from the light they are. Put the LED colored light on

DANCE PARTY MODE AND WATCH THE FUN BEGIN!

9400 SOUTHRIDGE PARK COURT SUITE 200 ORLANDO, FLORIDA 32819 USA

Tel: 407.855.5630 Fax: 407.210.8679 savilights.com

11.2014

Minumum and Maximum Cord Lengths Per Voltage Input

oltages are determined by the measured Voltage level @ the

Bus Bar where the Transformer and Cords are connected while on White

MELODY & BLANCO MIN/MAX VOLTAGE PER CORD LENGTH

CORD LENGTH Min. Voltage Max. Voltage

15 Feet 7.8Vac 12.0Vac

30 Feet 8.6Vac 12.2Vac

50 Feet 9.4Vac 12.4Vac

100 Feet 10.7Vac 13.2Vac

150 Feet 11.82V 13.8Vac

MEL-SOL & BLANCO PRO MIN/MAX VOLTAGE PER CORD LENGTH

CORD LENGTH Min. Voltage Max. Voltage

20 Feet 9.8Vac 12.0Vac

30 Feet 9.92Vac 12.2Vac

50 Feet 10.34Vac 12.56Vac

100 Feet 10.9Vac 13.5Vac

150 Feet 11.43Vac 14.1Vac

Next Step Products provides these guidelines as a reference for proper operation. Failure to adhere

specifications could result in improper operation or synchronization of lights.

ALL VOLTAGE READINGS ARE TAKEN WHILE LIGHTS ARE ALL SET TO WHITE

As these Charts address the Minimum - please remember that at no time should the MAXIMUM

distance with or without J Box extend past 150 ft.

9400 SOUTHRIDGE PARK COURT SUITE 200 ORLANDO, FLORIDA 32819 USA

Tel: 407.855.5630 Fax: 407.210.8679 savilights.com

11.2014

BASIC TROUBLESHOOTING GUIDE - FOR ADDITIONAL INFORMATION CONTACT

TECHNICAL SERVICES AT TELEPHONE NUMBERS LISTED BELOW

ALL LIGHTS FAIL TO ILLUMINATE - Check 120V power supply into transformer - Check for 12V

output at transformer - check or reset GFCI. Make sure 120 volts has not been used in the

installation of these lights - damage is assured and is NON WARRANTY.

ONE OR MORE LIGHTS DIM - This is generally caused by a poor connection or improper wire

gauge. To determine if light or lights has fault - separate each light from all other lights and

independently wire 12V to this light only. Repeat process on each light. If junction box is used -

recheck for proper connection of light cord. AGAIN IF A JUNCTION BOX IS BEING USED - VERIFY

THAT THE CORRECT WIRE GAUGE IS BEING USED BETWEEN TRANSFORMER AND JUNCTION BOX.

EVEN THOUGH OTHER LIGHTS MIGHT WORK CORRECTLY - IMPROPER WIRE GAUGE SIZE COULD

ALLOW 1 OR MORE LIGHTS TO WORK IMPROPERLY. Measure and verify that proper low voltage is

being supplied to lights - see WIRE GAUGE & WIRE LENGTH GUIDE CHART.

BLINKING, FLASHING, NON WORKING LIGHTS - This is generally caused by a poor connection

or improper wire gauge. To determine if light or lights has fault - separate light from all other lights

and independently wire 12V to this light only. Repeat process on each light. If junction

box is used - recheck for proper connection of light cord. AGAIN IF A JUNCTION BOX IS BEING

USED - VERIFY THAT THE CORRECT WIRE GAUGE IS BEING USED BETWEEN TRANSFORMER

AND JUNCTION BOX. EVEN THOUGH OTHER LIGHTS MIGHT WORK CORRECTLY - IMPROPER

WIRE GAUGE SIZE COULD ALLOW 1 OR MORE LIGHTS TO WORK IMPROPERLY. Measure and

verify that proper low voltage is being supplied to lights - see WIRE GAUGE & WIRE LENGTH

GUIDE CHART. MOST IMPORTANTLY SEE CHART FOR MIN/MAX VOLTAGE & CORD

LENGTH CHART.

SAVI LED LIGHTING PRODUCTS

COLORED LIGHTS OUT OF SYNCH - Follow Synchronization Instructions in this Guide. Be very

patient and read instruction carefully. If lights fail to synchronize - verify that proper wire

connections are being achieved for those lights that are out of step with others. Generally a lights

failure to sync with the rest is: improper voltage supply or poor connection to light.

NOTE: In most situations problems come down to 4 main faults: improper voltage supply,

improper wiring gauge,improper/poor wiring connections or the light itself.

SAVI LED LIGHTS ARE FIELD SERVICABLE AND THE CORD AND LIGHT BODY FIXTURE

SHOULD NOT BE REMOVED COMPETELY FROM THE CONDUIT OR POOL. THERE SHOULD BE

ENOUGH CORD SUPPLIED IN THE SERVICE LOOP TO REMOVE LIGHT FROM WALL FITTING AND

LIFTED ABOVE WATER LEVEL FOR LED LIGHT CARTRIDGE REPLACEMENT. IF THERE IS NOT

ENOUGH CORD IN SERVICE LOOP OR IT CANNOT BE ACCESSED - POOL WATER CAN BE DRAINED

BELOW LIGHT TO ACCESS FRONT OF LIGHT.

DO NOT PULL LIGHT AND CORD ENTIRELY FROM CONDUIT UNLESS INSTRUCTED BY COMPANY.

SAVI POOL AND SPA WILL NOT ACCEPT ENTIRE LIGHTS BEING RETURNED FOR SERVICE

UNLESS INSTRUCTED BY COMPANIES TECHNICAL SERVICES DEPARTMENT

ONLY LED LIGHT CARTRIDGES SHOULD BE REPLACED OR EXCHANGED WITH THE

PRODUCT

Refer to the Light Cartridge Replacement Instructions included in this Guide for light replacement.

WARNING: All servicing of Savi LED Lights should be done by a licensed or certified electrican or a

qualified pool professional in accordance with the National Electric Code (NEC) or Canadian Electric

Code (CEC)

For additional troubleshooting assistance or installation advice please contact Technical

Services at telephone number below.

9400 SOUTHRIDGE PARK COURT SUITE 200 ORLANDO, FLORIDA 32819 USA

Tel: 407.855.5630 Fax: 407.210.8679 savilights.com

10.2014

9400 SOUTHRIDGE PARK COURT SUITE 200 ORLANDO, FLORIDA 32819 USA

Tel: 407.855.5630 Fax: 407.210.8679 savilights.com

11.2014

TURN OFF MAIN POWER TO LIGHT BEFORE INSTALLATION

STEP 1

TURN OFF MAIN POWER TO LIGHT BEFORE

REPLACING LIGHT CARTRIDGE. Be sure the

light fixture is in a dry environment. Remove the (8)

eight screws from the lens with the tool provided.

Pull the lens from the fixture body. Remove and

discard the O-ring between the Lens and Fixture

Body.

STEP 2

Using the tool provided, insert and turn the thread-

ed portion into the extraction hole in the face of the

Light Cartridge. Pull the Light Cartidge from the

housing body.

STEP 3

Insert the replacement cartridge into the housing

body. Line up the TAB at the end of the circut board

with the receiving slot inside the housing body.

It may be necessary to slowly turn the Light

Cartridge until the TAB lines up with the SLOT.

STEP 4

Clean the Lens and the Enclosure of any remaining

old Silicone before applying new Silicone and replac-

ing the Lens. Replace the O-ring with the new one

provided. Attach the lens onto the fixture body.

Tightly secure the eight (8) screws indicated in the

diagram to the right. Once all screws are tight, slowly

submerse in water, checking for any air bubbles -

quickly remove from water bubbles appear as it

indicates the seal is not water tight. Retighten the

screws and test for bubbles again.

STEP 5

Reset the fixture into the wall fitting and turn the power ON.

Apply a new silicone bead to

the lens with tube provided

after cleaning the lens and

body of old silicone.

LIGHT CARTRIDGE REPLACEMENT

MINI MEL, MINI BLANCO,MELODY / SOL / BLANCO / BLANCO PRO

ALL LIGHT FIXTURESSHOULD NEVER BE ELECTRICALLY

CONNECTED TO A POWER SOURCE OTHER THAN AN APPROVED POOL “SAFETY"UL LISTED

OUTDOOR RATED CLASS 3, 12VAC TRANS-FORMER. THE SAVI NOTE SHOULD ONLY BE CONNECTED

TO THE SAVI M4 CONTROLLER. FAILURE TO COMPLY WILL EITHER DAMAGE OR DESTROY THE LIGHT

FIXTURE AND VOID THE WARRANTY.

TAB

SCREW TIGHTENING DIAGRAM

SILICONE BEAD ON LENS

SLOT

O-Ring

New O-Ring

Lens

Extraction Tool /

Screw Driver

Light Cartridge

Replacement

Light Cartridge

Fixture Body

Consult Factory for proper selection of

Replacement Cartridges. Very important for

proper operation

9400 SOUTHRIDGE PARK COURT SUITE 200 ORLANDO, FLORIDA 32819 USA

Tel: 407.855.5630 Fax: 407.210.8679 savilights.com

11.2014

LIMITED PRORATED WARRANTY

(herein referred to as “the Company”),

warranties its products, excluding lamps, to be free from defects in material and/or workmanship, under normal

condition,useandservice,foraperiodofFive(5)yearsfromthe date of manufacture. During the first two (2) years

100% coverage on all parts, 3rd (3) year all warranty parts will be replaced at

35%

of the then current List Price of such

part and in years Four & Five (4&5) all warranty parts wil be replaced at 50% of the then current List price of such part.

This specific warranty is for parts only and specifically excludes all labor charges associated with warranty items.

TERMS AND CONDITIONS:

ThiswarrantyonlyapplieswhentheCompany’sproductsareproperlywiredandinstalledtogetherasasystem;

andoperatedwithintheelectricalvaluesshownontheCompany’sspecification sheets;usedinlightingequipment

designedandapprovedfortheapplicationandenvironmentalconditions(temperature,humidity)withinthenormal

specified operatingrangeofthesystem.Thiswarrantydoesnotapplytoanyabnormaluseinviolationofanyapplicable

standard,codeorinstructionsforuseininstallationsincludingthosecontainedinthelatestNationalElectricalCode

(NEC),theStandardsforSafetyofUnderwritersLaboratory,Inc.(UL),StandardsfortheAmericanNational

StandardsInstitute(ANSI),inCanada,theCanadianStandardsAssociation(CSA),Europe(CE),Australia(C-

Tick).Thiswarrantywillnotapplyintheeventofconditionsdemonstratingabnormaluseorstress,including

under/overvoltageconditions, excessiveswitchingcycles,excessiveoperatinghours,alterations,accident,theft,

misuse,abuseanddamagedcausedbynegligentinstallation,impropermaintenanceorwhereadequatecarehasnot

beentakentopreventdamagetothelightingsystem.ReplacementoftheCompany’sproductcomponentswithany

othermanufacturerwillvoidtheentirewarranty.

WARRANTY SERVICE CLAIMS:

TheCompanymustissueaReturnMaterialAuthorization(RMA)numberforallrequestsforwarrantyreview.Toexpedite

service,pleasecontacttheCompany’sCustomerRepresentativewhereyoupurchasedtheproduct.Ifyouareunsure

whetherasituationexiststhatiscoveredbythiswarranty,pleasecontacttheCompany’scustomerservicedepartment

from the company or division where you purchased the product for assistance. In the event of a defect in material or

workmanshipduringthewarrantyperiod,theCompanywillrepairorreplace(atitsowndiscretion)itsproductsunder

the conditions of the warranty.

AcompletelistoftheCompany’sbrandsandtheirwarrantyservicecontactinformationcanbefoundattheendthe

warranty.

RETURN OF DEFECTIVE PRODUCT:

AftercontactingthepropercompanyordivisionandreceivingtheRMA#,thepurchaser/usershallpromptlyreturnthe

productafterreceivinginstructionsregardingif,whenandwheretoshipproduct.Productmustbereturnedwithin30

daysofreceivingRMA#.ShippingboxmustbeclearlymarkedwithRMA#.Failuretofollowthisprocedureshallvoidthis

warranty.Thecompanywillcoverexpensesformaterialbutwillnotcovershippingcosts.Productsreturnedwithoutan

RMA#willberefusedandreturnedtosenderatthesendersexpense.

REPLACEMENTOFPRODUCT,LIMITSOFLIABILITY:

TheforegoingshallconstitutetheexclusiveremedyofthepurchaserandthesoleliabilityofSavi Pool & Spa

regarding its products and component warranty. NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE IS MADE OR IS TO BE IMPLIED. In no event shall Savi Pool & Spa beliableforanyother

costsordamagesincludinglaborcharges,lostprofits orrevenues,incidental,specialorconsequentialdamages.The

Companyreservestherighttoexamineallfailedproductsandcomponentstodeterminethecauseoffailureand

patternsofusageandreservestheright to be the sole judge as to whether any product or component is defective

and covered under this warranty. THIS WARRANTY IS ONLY TO THE ORIGNAL PURCHASER OF PRODUCT AND

DOES NOT TRANSFER. October 1, 2013

Savi Pool & Spa

9400 SOUTHRIDGE PARK COURT SUITE 200 ORLANDO, FLORIDA 32819 USA

Tel: 407.855.5630 Fax: 407.210.8679 savilights.com

11.2014

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Savi Unterwasserbeleuchtung Handbücher

Savi

Savi SAVI-NOTE75 Bedienungsanleitung

Beliebte Unterwasserbeleuchtung Handbücher anderer Marken

Keldan

Keldan VIDEO 18X 25000lm CRI82 Bedienungsanleitung

Oase

Oase ProfiLux Garden LED RGB Bedienungsanleitung

Oceanled

Oceanled DISCOVER D3 Bedienungsanleitung

NORBIT

NORBIT AQUA FCL600 Bedienungsanleitung

Keldan

Keldan VIDEO 8XR Ambient 18000lm Bedienungsanleitung

Ikelite

Ikelite PCm - LED Light Bedienungsanleitung

LIGMAN

LIGMAN NEMO 2 Bedienungsanleitung

Oase

Oase Lunaqua 2 Handbuch

Kripsol

Kripsol 061511213000 Bedienungsanleitung

Wibre

Wibre 4.0291 Bedienungsanleitung

Certikin

Certikin PU9CS Bedienungsanleitung

lumishore

lumishore SMX53-SUPRA Bedienungsanleitung

Pyle

Pyle PLEDFN8 Bedienungsanleitung

Filix

Filix Arpool XM Bedienungsanleitung

Aqualuma

Aqualuma Pathway Light Bedienungsanleitung

HEISSNER

HEISSNER U 130-T Bedienungsanleitung

emaux

emaux NP300 Series Bedienungsanleitung

Oceanled

Oceanled XD16 Bedienungsanleitung