SC&T HD401F-5M Bedienungsanleitung

Smart Cabling & Transmission Corp. V1.0

Fiber Optical Solution

User Manual

Model : HD401F-5M

Single Channel HD-TVI/AHD/HDCVI/CVBS with

RS485 Fiber Extender 20KM

User Manual

HD401F-5M

Introduction

HD401F-5M is a coaxial-to-fiber-optic media converter that can send an uncompressed 5MP HD-TVI/ AHD/

HDCVI/ CVBS and RS485 signals for an extra-long distance. The product is a perfect solution for a CCTV

security system to send multiple camera videos to a remote DVR for recording.

Features

Supports HD-TVI, AHD, HDCVI, PAL, NTSC, SECAM video formats.

Resolution up to 5MP (2560 x 1920).

Signal extension up to 20KM over single mode fiber optic cable.

Supports half-duplex RS485 transmission.

Built-in 4kV surge protection in terminal blocks.

Installation View

Cable & Transmission Distance

The transmission distance may vary by the quality of connected devices (Cameras, DVRs), connectors,

and cables.

Connector

Type

Diameter

Max. Distance

Single Mode

9/125µm

20KM

BNC

RG59/6U

75Ω

100M

User Manual

HD401F-5M

Resolution

Pixels

Frame Rate

1MP (1280 x 720)

30/50 fps

1.3MP (1280 x 960)

30 fps

2MP (1920 x 1080)

25/ 30 fps

3MP (2408 x 1536)

20 fps

4MP (2560 x 1440)

15 fps

5MP (2560 x 1920)

12.5 fps

RS485 Pin Assignment

Designation

GND

RS485+

RS485-

User Manual

HD401F-5M

Panel View

No.

Interface

Description

Fiber FC connector

To connect a single mode fiber cable

To indicate the status of power

Fiber

To Indicate the connecting status of fiber port

Video

To indicate the connecting status of BNC port

Video In/Out

To connect a RG59/ 6U coaxial cable

Data

To indicate the status of RS485 signal

RS485 In/Out

To connect a RS485 device

DC 5V

To connect a DC5V 2A power adapter

Grounding

To connect a wire to the earth ground

User Manual

HD401F-5M

Installation Guide

The video transmission systems series are preset for use with the data protocol RS-485. Simply connect

the signal, power supply and fiber optic cables between the two units. There are indicator LEDs on the

units for monitoring the real-time status of power and data. The following instructions describe the typical

installation procedure and the function of the LED indicators located on each unit.

1. Connect the video source (camera) to the video input BNC connector on the transmitter unit using

coaxial cable.

2. Connect the video output BNC connector on receiver unit to the video monitor using coaxial cable.

3. Connect the fiber optic cable between the transmitter and receiver.

4. Apply the power supply to both transmitter and receiver.

5. When the power is applied, the POWER LED will light, indicating the presence of operating power.

The VIDEO and the DATA LEDs will give an indication as stated in the following section.

6. The system should now be operational.

LED Indication

LED Name

LED Color

Description

Green ON

Power On

Fiber

Green ON

Fiber optic cable linked

Video

Green ON

Video source detected

Data

Green ON

RS485 signal transferring

Caution

The transmitter unit contains a light-emitting diode located in the optical connector. This device emits

invisible infrared electromagnetic radiation that can be harmful to human eyes. The radiation from this

optical connector, if viewed closely without a fiber optic cable connected to the optical connector, may

cause instantaneous damage to the retina of the eye. Direct viewing of this LED should be avoided at all

times.

This product is designed for indoor applications. If it is desired for outdoor use, please install

additional equipment for waterproof protection and surge protectors to prevent damages

caused by lightening.

Both transmitter and receiver have to be powered with the appropriate power adaptor.

DO NOT put anything on the power and system cables; place them where they cannot be stepped

on. Please be sure there is nothing resting on any cables.

Avoid using this product close to water places, or near high temperature devices such as radiators,

stoves, etc.

Using certified coaxial cables to transfer high-resolution video is recommended

Using standard and certified optical fiber cables to transfer high-resolution video is

recommended.

User Manual

HD401F-5M

Shut down the power supply and unplugged all equipment immediately if:

owater or any kind of liquid has been spilled into the product

othe product has been damaged by external forces

othe product does not operate normally as this manual indicates

oPlease contact us for further repair if above conditions happen.

What’s included in the package

Please check the following items in the package before installation. If there is any loss or damage to the

items, please contact the dealer immediately.

No.

Item

Qty

HD401FT-5M (Tx)

HD401FR-5M (Rx)

DC 5V 2A Power Adapter

Screw

Screw Plug

Rubber Pads

User Manual

HD401F-5M

Specification

ITEM NO.

HD401FT-5M

HD401FR-5M

Support

Video Format

HD-TVI/ AHD/ HDCVI/ CVBS

Max. Video Resolution

5MP (2560 x 1920) @12.5fps

Video Bandwidth

50MHz

Max. Distance

20Km

Data Baud Rate

0-200Kbps, Half-duplex (From Rx to Tx)

Input/ Output Wavelength

TX1310, RX1550nm

TX1550, RX1310nm

Input/ Output Level

>500mVP-P

1Vp-p

Return Loss

>15dB

Up/ Down Time

<0.8ns

Max. Jitter

<0.2UI

Ports & Interfaces

Video Input

1 x BNC (75Ω)

1 x FC, Single -mode

Video Output

1 x FC, Single -mode

1 x BNC (75Ω)

RS485 Interface

1 x 5-pin Terminal Block

Power

Power Supply

DC5V 2A

Power Consumption

≤3W

Ambient Temperature

Operation

-15 to 60℃

Storage

-40 to 85℃

Humidity

5~95% (Non-condensing)

Physical Characteristics

Dimensions

103 x 104.6 x 28.5mm

Weight

180g

185.4g

Inhaltsverzeichnis

Andere SC&T Extender Handbücher

SC&T

SC&T IP02 Bedienungsanleitung

SC&T

SC&T YW02A Bedienungsanleitung

SC&T

SC&T VKM02 Bedienungsanleitung

SC&T

SC&T VE02DALS Bedienungsanleitung

SC&T

SC&T VW02T Bedienungsanleitung

SC&T

SC&T IP03PT Bedienungsanleitung

SC&T

SC&T KM03 Series Bedienungsanleitung

SC&T

SC&T DKM01 Bedienungsanleitung

SC&T

SC&T HE05BT Bedienungsanleitung

SC&T

SC&T HE02PT Bedienungsanleitung

SC&T

SC&T Audio Extender Series Bedienungsanleitung

SC&T

SC&T DP01F-4K6G Bedienungsanleitung

SC&T

SC&T VE01HA Bedienungsanleitung

SC&T

SC&T HUE03T-4K Bedienungsanleitung

SC&T

SC&T HKM01B-4K Bedienungsanleitung

SC&T

SC&T KM03 Bedienungsanleitung

SC&T

SC&T RS002E Bedienungsanleitung

SC&T

SC&T HE02EI Bedienungsanleitung

SC&T

SC&T IP09P Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

SC&T

SC&T HE01F-4K Bedienungsanleitung

SC&T

SC&T HE01S Bedienungsanleitung

SC&T

SC&T HE02EIP Bedienungsanleitung

SC&T

SC&T HE20E Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung