SC&T HKM01 Bedienungsanleitung

HDMI & USB, AUDIO, RS232, IR CAT5 Extender

ITEM NO: HKM01 HDMI & USB, Audio, RS232, IR CAT5 Extender Over IP

The HKM01 HDMI, USB with Analog audio, RS232, and IR CAT5 extender design for extends and distribute

all signals over one CAT5 up to 150 meters, with local HDMI monitor output. It provides superior video

quality up to 1920 x 1200 resolutions, and using cost effective Cat5e cable, instead of HDMI, RS232 cables,

for an easy, neater and reliable installation. The local and remote units can be connected together for a

Point-to-Point connection via CAT5e/6 cable or a Point-to-Many connection via a managed network switch.

It is optimized for applications at broadcasting system, multimedia display and multi-data sharing, digital

signage, home network integration, and industrial control, hospital, education, security, Matrix network

system and system control over RS232 and equipment control over IR.

Features:

Extend HDMI, RS232, IR and USB signals over one CAT5E/CAT6 cable.

Supports resolutions up to 1080p Full HD and 1920 x 1200 (WUXGA) 32bpp@ 60 Hz

Transmission range up to 150M over CAT5e, 180M over CAT6.

Supports 2-way RS232 commands at baud rate 115200 (control software on a PC, or

other automated control system hardware) to control devices attached to the matrix using

RS232. Full Duplex data communication.

HDMI 1.3b and HDCP compliant.

HDMI audio support up to LPCM 7.1@192Khz

Built in Bi-Directional analog audio.

Built in Bi-Directional IR.

HKM01T transmitter unit built in HDMI loop output.

Receiver unit with 4 ports USB devices (1 port USB 1.1 & 3 Port USB 2.0), to extend USB

peripheral devices, such as flash disk, hard disk, keyboard, mouse, etc.

Support point to point and multiple source devices to multi-display connections via

Gigabit network switch.

Perfect for control remote machines and security monitoring systems, digital signage

application.

Optional model: SR01 signal repeater for longer distance application.

Installation View:

Point to Point Direct Connection:



Over Gigabit Ethernet switches: One to Multiple or Multiple to Multiple Connection:

1 Input to Multiple outputs connections via a Gigabit network switch

Multiple Inputs to Multiple outputs connections via a Gigabit network switch

Recommend installation using an independent Gigabit LAN; do not link with existing LAN to

avoid a lot of video data transmission slow down your network system.

When using multiple transmitters and receivers via a Gigabit network switch, identically

configure dip switches on the local and remote units to link them together.

In multiple connections keyboard and mouse are plug and play, for other USB devices just

simply press and click the USB keyboard Pause/Break” KEY on a receiver for three times to

get USB control; only one unit can have USB control over the source at any time.

For configurations that require greater distances, cascade the managed network switches to

extend the distance between the transmitter and receiver. Up to 16 transmitters can be

connected per individual network switch or between cascaded network switches.

Optional Model: SR01 Signal Repeater (order separately)

Extend data signal for an additional 120meters.

Application for HKM01 signals for extra long range transmission.

Ability to cascade connection with multiple SR01 for long range transmission

Built in LED status indication.

External power required.

Plug and play for easy installation.

Work with HKM01 CAT5 Extender:

Panel View:

Transmitter

Receiver

LED Indication Status:

Power (Green LED): Flash HKM01 Booting

ON HKM01Bootcompleted

Link (Blue LED): Flash Connection or connected but no HDMI input

ON linking

RJ45 LED: Green Flash (Data transmission)

Orange On (linking)

Back Panel Rotary Switch Function:

HKM01 rotary switch could switch 0~F total 16 channels, HKM01T and HKM01R must be setting at

same channel in order to do mutual transmission.

Front Panel Button Function:

One to one Application as below chart:

ITEM HKM01T HKM01R

Button LINK FUNCTION LINK FUNCTION

Short Press Loopback and

Remote output /

Loopback output

only

Video Mode/

Graphic Mode*Link on : Link

Link off : Unlink Video Mode/

Graphic Mode*

Long Press (3

seconds) Remote output only

(on/off)* Anti-Dither

(1/2/off)* N/A Anti-Dither

(1/2/off)**

Press to power off

(Press and hold until

Green LED and Blue

LED Flash)

RESET to Default* N/A RESET to Default* N/A

Above “bold font” part as the default

One to Multiple Applications as below chart:

ITEM HKM01T HKM01R

Button LINK FUNCTION LINK FUNCTION

Short Press Loopback and

Remote output /

Loopback output

only

Video Mode/

Graphic Mode* Link on : Link

Link off :Unlink Video Mode/

Graphic Mode*

Long Press

(3 seconds) Remote output

only (on/off)* Anti-Dither

(1/2/off)* USB Link (on/off) Anti-Dither

(1/2/off)*

Press to power on

(Press and hold until

Green LED Flash) N/A Use Loopback

EDID * N/A Update EDID*

Press to power off

(Press and hold until

Green LED and Blue

LED Flash)

RESET to Default* N/A RESET to Default* N/A

Above “bold font” part as the default

Multiple to Multiple Mode Function:

HKM01 could do Multicast mode with back panel Rotary Switch function, to do multiple to multiple

transmission must consider bandwidth and data rate, it could be setup several groups as below :

HKM01 Switch can be set to a max. 16 channels, to work with a Gigabit Switch Hub, HKM01T and

HKM01R need to need to switch same channel in order to linking each other.

The video inputs highest rate around 150 ~200 Mbps, HKM01T could setup at max. 6 units as source

when using Gigabit Switch Hub.

Cable:

Link Cable use high quality Cat.5e UTP/STP/FTP or Cat.6 UTP cable

Ethernet Switch Hub Recommendation：

Recommend to use IGMP and Jumbo Frame over 8K Ethernet Switch Hub in order to achieve the

best transmission quality

HOT KEY Function：

HKM01 could use Ethernet Switch Hub to do one to multiple application, Under multiple HKM01R

for switching HKM01R external host USB flash drive port, make the external flash drive you want to

use with an external USB keyboard, to click three times “Pause/Break” KEY, the system will

redetect and connect USB devices.

Caution：

1. HKM01 do not recommend to work with general LAN connection to avoid large video

Data transmission or multicast packets to slow down your other LAN devices.

2. When use HKM01T “Line In” function, the HDMI audio output of HKM01R Receiver will be

disabled.

3. When doing one to multiple applications, the HKM01R Receiver “MIC” won’t be affected.

4. IR receiving angle ±55degree, emitting angle 30degree，distance reach to 3-5 meters.

Web Setting Function：

HKM01 default setup at one to multiple mode (Multicast), the detailed setting could be changed via

the web UI, the setting as below:

Installation and connection:

1. Install BonjourSDKSetup.exe

2. Right click on “My Network Place” “Properties” then right click on “Local Area Connection”

“Properties” then double click on “Internet Protocol (TCP/IP)” to setting as below: (IP

address 169.254.111.111, sub mask 255.255.0.0)

3.Use CAT5 cable to connect transmitter RJ45 port to PC LAN port, open IE browser then select

View Explorer Bars Bonjour.

4. Double click on “HTTP on ast-gateway(HKM01T)” or “HTTP on ast-client (HKM01R)”, it will

pop up web setup in Bonjour windows as below:

5. Select Network page

IP Mode : Auto IP、DHCP、Static three modes, select one of them and press “Apply” to finish

setting.

Casting Mode : Multicast(one to multiple ) and Unicast(one to one) two modes ,select and

press “Apply” to finish setting ( If setup at Multicast, pick Auto select USB operation mode per

casting mode)

6. Function setup

HKM01T Video over IP: This function setup the video signals send from network, select and enter

“Apply” finish setting

Please note it will turn off HDMI output if this function be disabled, only analog audio output

HKM01R Video over IP : This function setup the video signals send from network, select Copy

EDID from this Video Output and enter “Apply” finish setting (pick up this item will auto copy

HKM01R TV EDID)

In multiple connections the EDID will copy from the last connected receiver.

USB over IP Setup: This function setup the USB signals send from network.

In Unicast (one to one) mode: Operation Mode selects “Active per request” and enters “Apply” to

finish setting.

In Multicast (one to multiple) mode: Operation Mode select “Auto select mode” and enter “Apply” to

finish setting.

Serial over IP：This function setup Serial (RS232) signal sends from network

[Baud Rate Default：115200]

Operation Mode selects “Type 2 (Recommended. Dumb redirection.)” And enter Apply to finish

setting.

Baud rate Setting for Type 2 : It could change Baud rate as below : 300, 600, 1200, 2400,

4800, 9600, 14400, 19200, 38400, 57600, 115200, 230400

RJ45 Define:

Link Cable (TIA/EIA-568-B)

1. Orange-white Data 1 +

2. Orange Data 1 -

3. Green-white Data 2 +

4. Blue Data 3 +

5. Blue-white Data 3 -

6. Green Data 2 -

7. Brown-white Data 4 +

8. Brown Data 4 -

Package Include:

HKM01T Transmitter x 1

HKM01R Receiver x 1

USB A to B cable x 1

IR emitter cable x 1

DC 5V 2Amp power adapter x 2

Specification:

ITEM NO. HKM01T HKM01R

Support Resolution 1920 x 1200p 32bpp@ 60 Hz

Transmission Distance CAT.5e：150M / CAT.6：180M (Max)

HDMI Connector HDMI Type A x 2 HDMI Type A x 1

USB Connector USB Type B x 1 USB Type A x 4

RS232 Connector DB9 (Female) x 1 DB9 (Male) x 1

Link Connector RJ45 x 1

Audio Connector 3.5 mm Phone Jack x 2

IR Connector 3.5 mm Phone Jack x 1

IR Receive/Emit Angle Horizontal ± 45, Vertical ± 35 / ± 30

IR Receive/Emit Distance 5 M

Power Supply DC 5V 2A

Power Consumption 1.3Amp (Max.)

Temperature Operation: 0 to 55 , Storage:℃-20 TO 85 , Humidity: up to 95%℃

Dimensions mm 125 x 140 x 30

Weight g 380

Rev.A1

Inhaltsverzeichnis

Andere SC&T Extender Handbücher

SC&T

SC&T RS002E Bedienungsanleitung

SC&T

SC&T HD401F-5M Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

SC&T

SC&T VHE02EIP Bedienungsanleitung

SC&T

SC&T HE02EIR Bedienungsanleitung

SC&T

SC&T IP02ET Bedienungsanleitung

SC&T

SC&T VKM02 Bedienungsanleitung

SC&T

SC&T Audio Extender Series Bedienungsanleitung

SC&T

SC&T IP05I Bedienungsanleitung

SC&T

SC&T UE01 Bedienungsanleitung

SC&T

SC&T HE01SE Bedienungsanleitung

SC&T

SC&T HKM02B-4K Bedienungsanleitung

SC&T

SC&T HE05BT Bedienungsanleitung

SC&T

SC&T DP02U Bedienungsanleitung

SC&T

SC&T HE01C Bedienungsanleitung

SC&T

SC&T KM03 Series Bedienungsanleitung

SC&T

SC&T HKM01E Bedienungsanleitung

SC&T

SC&T VW02T Bedienungsanleitung

SC&T

SC&T VE02DALS Bedienungsanleitung

SC&T

SC&T HKM01BT Bedienungsanleitung

SC&T

SC&T VKM04 Bedienungsanleitung

SC&T

SC&T HE03L-4K Bedienungsanleitung

SC&T

SC&T VE05AL Bedienungsanleitung

SC&T

SC&T HE02EIP Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung