Schiit AEGIR Bedienungsanleitung

STEREO OR MONO CONTINUITYTM POWER AMP

IN NORSE MYTHOLOGY, AEGIR WAS THE LORD OF THE OCEAN.

AND NO, THAT DOESN’T MEAN OUR AEGIR IS LIQUID-COOLED.

NOR WILL OUR AEGIR NECESSARILY HAVE NINE DAUGHTERS.

BUT AEGIR MAY MAKE SOME WAVES OF ITS OWN.

SINCE IT’S OUR FIRST CONTINUITYTM SPEAKER AMP.

AEGIR

OWNER’S MANUAL

Aegir is, depending on your point of view, either

(1) a breakthrough in constant-transconductance

amplication that extends the benets of Class

A operation and offers a unique solution for mis-

match between N and P output devices with our

Continuity™ technology, or (2) a hotter-running,

lower-power version of Vidar. In either case, if

you nd yourself in posession of an Aegir, this

manual will help you understand how to get the

most out of it.

INTRODUCTION

WHAT’S IN THE BOX

(1) Aegir

(1) Power cord

(0) Stick-on feet (they’re screwed in)

The following is required by the roughly 9,542

government agencies and regulations we have to

comply with. If you have some common sense, they

should seem pretty straightforward. In any case, read these

instructions before proceeding farther, follow all instructions,

and heed all warnings. Or else!

1. If you don’t know how to install audio devices, get a

qualied professional to help.

2. Never use this device near water, and clean only with a

dry cloth.

3. Assure adequate ventilation, do not block any ventilation

openings, or place near heat sources.

4. Use only the supplied power cord or suitable replacement.

Route cords away from trafc areas and protect them from

being pinched. Unplug the cord from the outlet if the apparatus

is unused for a long period of time.

5. To prevent electric shock, do not use the plug with an

extension cord, receptacle, or outlet unless blades can be

fully inserted.

6. Refer all servicing to qualied service personnel. Service is

required when the device has been damaged, including cord or

plug damage, liquid has been spilled or objects have fallen into

the device, the device has been exposed to rain or moisture,

does not operate normally, or has been dropped.

WARNING: TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS DEVICE TO

RAIN OR MOISTURE.

CONTINUITY™

POWER AMPLIFIER

SCH-09K

0A19C2832

115VAC 450W

STEREO CONNECTION

1 Right and Left Speaker Outputs. When using

Aegir as a stereo amp, connect your right

speaker to the right red and black output

terminals and your left speaker to the left red

and black output terminals.

2 RCA Inputs. Similarly, connect your source

(usually a preamp) using high-quality RCA

cables—right into the input marked “R”, and left

into the input marked “L”.

3 AC Input. Connect to a wall socket with the

provided AC cord. Or you can use any IEC-type

cord; ours isn’t special.

4 Power Switch. Up is on. Down is off. Pretty

simple. You can leave Aegir on all the time

if you’d like, and save power by putting it in

Standby mode using the button on the front.

CONTINUITY™

POWER AMPLIFIER

SCH-09K

0A19C2832

115VAC 450W

1 and 2 Speaker Outputs. When using Aegir as

a mono amp, connect your speaker to the two

top red terminals only. Right is “+”, and left is “-”.

Please note both of these are active outputs—do

not ground one of them!

3 XLR Input. Connect a balanced source (usually

a preamp) using a high-quality XLR cable. It’s

important that the preamp is truly balanced for

proper operation.

MONO CONNECTION

1 2

4 AC Input. Connect to a wall socket with the

provided AC cord. Or you can use any IEC-type

cord; ours isn’t special.

5 Power Switch. Up is on. Down is off. Pretty

simple. Feel free to leave the amp on all the time

if you’d like.

CONTINUITY™

POWER AMPLIFIER

SCH-09K

0A19C2832

115VAC 450W

1Standby/Alert Light. When this light is on,

Aegir is in Standby mode—the amp is muted and

the output stage is de-biased. This light also

serves as an alert light. It flashes during self-

check on startup and flashes if there is a fault.

2 Standby Button. Press this button to put Aegir

in Standby mode and reduce power draw. Press

again to take Aegir out of Standby mode for

normal use.

OPERATION

3Operate Light. When this light is on, Aegir is in

Operate mode (that is, it will play music when fed

a musical signal from an appropriate source.)

4 Heatsinks. These get plenty hot when in use.

Ensure there’s plenty of space on either side

of the amp and good ventilation above. If your

home is particularly warm (like, 30C and above),

you may need to use additional cooling—like, you

know, a fan—to avoid thermal shutdown).

Okay, so you have a flashing light. Deep breath.

We’ll get this taken care of shortly.

When Aegir’s front right light flashes during

operation (and the amp mutes), or if it never

stops flashing after you turn on the amp,

there’s a problem, or fault. There are three

kinds of faults:

1. Over-temperature. The heatsinks are too hot,

and Aegir has shut down to protect its output. If

the amp is very hot, turn it off, wait a while for it

to cool down, and try turning it on again. Aegir

runs very high standing bias and runs very hot;

in very warm homes (30 degrees C/85 degrees

F, for example), you may need to use a fan for

additional cooling to avoid overtemperature

shutdown.

2. Over-current. It’s unlikely that Aegir will run

into over-current protection playing almost any

speaker, but if the speaker cables are shorted, or

there is an internal fault in the speaker, you may

run into over-current protection.

CLEARING FAULTS

To troubleshoot this, turn off the amp, discon-

nect the speaker cables from the amp, and turn it

back on again. If it comes back on, there may be

a short in your speaker cables (or your speakers).

Examine your connections to ensure there are

no stray wires or shorts. Once those have been

xed, you can reconnect the speakers and play

music again.

3. High DC offset. Aegir is a DC-coupled amp. Its

microprocessor monitors DC levels at the output

and adjusts it down to zero. However, it may not

be able to correct for high DC from your source

(such as a preamp). To clear this fault, turn off

the amp, disconnect the RCA cables or XLR cable

from the amp, and turn it back on again. If the

amp turns on normally, then there may be high

DC on the output of your source. Have the source

inspected and repaired.

5-YEAR LIMITED WARRANTY

Schiit Audio warrants to the original purchaser that this product shall be free from defects in mate-

rial and workmanship for ve (5) years from the date of purchase. If a defect covered by this warranty

occurs during this period, Schiit Audio will repair the defective product, free of charge. Date of purchase

will be based on customer receipts, otherwise date of manufacturing will be used.

If you believe you need warranty service, contact us rst. Schiit Audio products sent back to us without

a Return Authorization (RA) will be returned to the sender without repair. To contact us and obtain an

RA, email [email protected].

Warranty Limitations. This warranty shall not apply if a product: (a) is modied or tampered with; (b) is

damaged by negligence, accident, unreasonably use, or other causes unrelated to defective materials or

workmanship, or (c) has had the serial number altered or removed.

Any implied warranties, including warranties of merchantability and tness for a particular purpose, are

hereby limited in duration to the warranty period of 5 years. In no event shall Schiit Audio be liable for

consequential or incidental damages resulting from the breach of any implied or expressed warranties.

Some states do not allow these limitations, so they may not apply to you. You may also have other

rights which vary from state to state or province to province.

Application for Council Directives 72/23/EEC

Conformity declared for EN60065, EN50082-1

SCHIIT.COM

[email protected]

Inhaltsverzeichnis

Andere Schiit Verstärker Handbücher

Schiit

Schiit Valhalla 2 Bedienungsanleitung

Schiit

Schiit MJOLNIR Bedienungsanleitung

Schiit

Schiit MAGNIUS Bedienungsanleitung

Schiit

Schiit REKKR Bedienungsanleitung

Schiit

Schiit GJALLARHORN Bedienungsanleitung

Schiit

Schiit KARA Bedienungsanleitung

Schiit

Schiit LYR+ Bedienungsanleitung

Schiit

Schiit SCH-07 Bedienungsanleitung

Schiit

Schiit FREYA S Bedienungsanleitung

Schiit

Schiit Saga+ Bedienungsanleitung

Schiit

Schiit SCH-20 Bedienungsanleitung

Schiit

Schiit MAGNI 2 UBER Bedienungsanleitung

Schiit

Schiit LYR+ Bedienungsanleitung

Schiit

Schiit ASGARD 2 Bedienungsanleitung

Schiit

Schiit RAGNAROK SCH-09 Bedienungsanleitung

Schiit

Schiit Mjolnir SCH-05 Bedienungsanleitung

Schiit

Schiit ASGARD SCH-01 Bedienungsanleitung

Schiit

Schiit Freya Bedienungsanleitung

Schiit

Schiit MJOLNIR 2 Bedienungsanleitung

Schiit

Schiit Asgard 3 Modular Continuity Bedienungsanleitung

Schiit

Schiit LYR Bedienungsanleitung

Schiit

Schiit LYR 2 SCH-03-2 Bedienungsanleitung

Schiit

Schiit MANI 2 Bedienungsanleitung

Schiit

Schiit Fulla 2 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung