Schlage KC9354 Bedienungsanleitung
KING COBRA/KING COBRA-2
NARROW STILE SERIES
57049-A 04-2007
KC9354/KC9354-2
Keypad Programmable
and SNAP Compatible Trim
For Narrow Stile Doors
KC9354/KC9354-2 INSTALLATION INSTRUCTIONS
Contents of the Box
57049-A Page 2 04-2007
KC9354/KC9354-2 INSTALLATION INSTRUCTIONS
Contents of the BoxContent s of the Bo x
KC9354/KC9354-2 INSTALLATION INSTRUCTIONS
Introduction / Tools and Materials Needed / Contact Info
57049-A Page 3 04-2007
Introduction / Tools and Materials Needed / Contact Info
Introduction:
The KC9354/KC9354-2 will allow access by allowing the trim to unlock the exit
device when an access code or iButton is entered and the turnpiece is turned coun-
terclockwise. Mechanical key override is standard. The trim is compatible with the
dogging features available with the Adams Rite® exit devices.
The KC9354/KC9354-2 is compatible with Adams Rite®8600 concealed ver-
tical rod exit devices and 4780 Series 2-point deadlatches w/paddle on alumi-
num doors.
Tools and Materials Needed:
Contact Information:
Schlage Lock Company
575 Birch Street
Forestville, CT 06010
technical support: 866-322-1237
fax: 866-322-1233
web: http://www.irsupport.net
1
.F
l
at
h
ea
d
screw
d
r
i
ver w
/
stra
i
g
h
t,
1/8”
w
id
e
bl
a
d
e
2. Small Philips head screwdriver
3. 1/16” Allen wrench
4. Long nose needle-nose pliers
5. Center punch
6. Hammer
7. Power drill
8. 19/32” drill bit
9. 1/4” drill bit
10. Jig saw w/blade
11. Drill & Tap for 10-32 threads
KC9354/KC9354-2 INSTALLATION INSTRUCTIONS
Door Preparation
57049-A Page 4 04-2007
Door Prepar ation
Door Conditions:
Installation may require the use of a cover plate (a) to cover the holes left in the door.
If an existing pull (b) must be removed, Ives offers a compatible pull.
>Schlage Cover Plate P/N: KC9000-KRP
>Ives Pull P/N: 8190-18-xxx (xxx = finish)
For factory prepped doors, use dimensions
shown. Dimensions are referenced from cen-
ter of 1-1/4” cylinder hole. Backset is deter-
mined by the Adams Rite® lock.
When installing new Adams Rite® locks,
do not install outside cylinder (because this
trim replaces it).
(3.957”)
(2.693”)
Backset is determined by
the Adams Rite® lock.
(6.656”)
b
a
Horizontal centerline for
Adams Rite® 8600 Rim
KC9354/KC9354-2 INSTALLATION INSTRUCTIONS
Cams, Cores, Cylinders and Blocking Rings
57049-A Page 5 04-2007
Cams, Cores, Cylinders and Blocking Rings
Cams For Mechanical Override Cylinder:
IC Cores:
Cylinders / Blocking Rings:
T
h
e K
C9000
tr
i
m requ
i
res t
h
e use o
f
a c
l
over
l
ea
f
cam
(
a
)
. T
hi
s
is a list of compatible Schlage parts. For other manufacturers,
consult cross-reference charts.
> Cam for Standard Mortise cylinder: Schlage Everest: L583-153
Schlage Classic: L583-254
> Cam for Interchangeable Core: Schlage IC Cam: L583-255
a
>
S
ma
ll
Format I
C
core w
/
cam:
S
c
hl
age:
80
-
108
-<FINI
S
H>
NOTE: This core requires the use of 1/4” blocking ring:
Schlage: 36-079-025-<FINISH>
> Fu
ll
Si
ze I
C
core w
/
cam:
S
c
hl
age:
30
-
016
-<FINI
S
H>
NOTE: This core requires the use of 3/8” blocking ring:
Schlage: 36-079-037-<FINISH>
T
h
e K
C9000
can use a
1
-
1/8”
mort
i
se cy
li
n
d
er w
i
t
h
out t
h
e use
of a blocking ring. For cylinders longer than 1-1/8” a blocking
ring is required. The blocking ring thickness is equal to the cyl-
inder length, minus 1-1/8”. For example, if you use a 1-1/2” cyl-
inder you need a 3/8” blocking ring. Compression rings can be
ordered from a Schlage distributor:
Thickness: Schlage Part Number:
N
o compression ring: 1/8” 36-079-012-<FINISH>
1/4” 36-079-025-<FINISH>
3/8” 36-079-037-<FINISH>
1/2” 36-079-050-<FINISH>
KC9354/KC9354-2 INSTALLATION INSTRUCTIONS
Installing the KC9354/KC9354-2
57049-A Page 6 04-2007
Installing the KC9354/KC9354-2
Installing the KC9354/KC9354-2
If your trim has a key cylinder already installed, skip to Determine Hand: on page 12. Other-
wise, continue with Loosen the Baseplate Screws: on this page.
1) Loosen the Baseplate Screws:
2) A Key Cylinder That Is At Least 1-1/8” Long Must Be Installed:
IMP
O
RT
A
NT: Do not remove any o
f
t
h
e screws
i
n t
h
e
f
o
l
-
lowing step or it will be difficult to reinstall them.
• Using a small Philips head screwdriver, loosen screws
a& bin baseplate, around key cylinder hole, one
turn.
NOTE: Screws a, b, c & d are set at the factory.
Screws a & b are tightened and screws c & d are left loose.
b
d
a
c
> T
h
e
k
ey cy
li
n
d
er t
h
at you
i
nsta
ll
must
b
e
1
-
1/8”
l
ong or
l
onger.
>>>> Do not attempt to install a key cylinder that is shorter than 1-1/8”
> The two photos below illustrate the difference between a 1” and a 1-1/8” key cylinder.
1” long key cylinder.
DO NOT ATTEMPT TO INSTALL A 1”
LONG KEY CYLINDER.
1-1/8” long key cylinder
ONLY INSTALL A KEY CYLIN-
DER THAT IS AT LEAST 1-1/8”
KC9354/KC9354-2 INSTALLATION INSTRUCTIONS
Installing the KC9354/KC9354-2
57049-A Page 7 04-2007
3) Make Room for Key Cylinder:
4) Hold Dead Latch in Place:
5) Verify Placement of Dead Latch:
Due to the d
i
ameter o
f
the key cyl
i
nder,
i
t
i
s necessary
to have dead latch (a) placed out of the way when
installing the key cylinder. Therefore...
• Using your finger or a pair of needle-nose
pliers, push dead latch towards the top end
of trim as indicated by arrow in photo.
NOTE: As indicated by arrow in photo, you’ll notice
that when you push the dead latch forward, it will
swing a little bit in a counterclockwise direction.
a
T
o
i
nsure that dead latch
i
s placed
f
ar enough out
o
f the way to allow key cylinder to be threaded in
p
roperly:
• Insert a finger into key cylinder hole and
hold dead latch firmly in place.
• Carefully turn the trim over while keep-
ing the dead latch in position.
Two holes on dead latch (a) should be showing
within the two holes (b) in baseplate.
Fig. 1
a
b
KC9354/KC9354-2 INSTALLATION INSTRUCTIONS
Installing the KC9354/KC9354-2
57049-A Page 8 04-2007
6) Install the Key Cylinder:
Table 1: Blocking Rings
Table 2: Recommended Cams
7) Align Key Cylinder:
Key Cylinder Length Blocking Ring (Schlage P/N; XXX = finish)
• 1-1/4” 1/8” (36-079-012-XXX)
• 1-3/8” 1/4” (36-079-025-XXX)
• 1-1/2” 3/8” (36-079-037-XXX)
• 1-5/8” 1/2” (36-079-050-XXX)
Cylinder/Core Schlage Type Part Number
• Standard Mortise Cyl Everest L583-153
• Standard Mortise Cyl Classic L583-254
• Interchangeable Core IC Cam L583-255
• Insta
ll
.
0
5
0”
cy
li
n
d
er was
h
er.
IMPORTANT: A .050” cylinder washer must be used IN ALL CASES,
regardless of the key cylinder length.
• If you are installing a cylinder that is longer than 1-1/8”, you
must also install a blocking ring (see Table 1: Blocking
Rings, on page 8).
A simple formula for determining blocking ring thickness is:
Blocking ring thickness = length of cylinder minus 1-1/8”
• If not already done, install cam onto cylinder. Cam must be clo-
ver leaf design (see Table 2: Recommended Cams, on page 8).
• Tilt top of trim down at a sharp angle.
• Screw in key cylinder until it stops. Use mechanical key as a han-
dle for turning if necessary.
•
Af
ter screw
i
ng
i
t a
ll
t
h
e way
i
n,
b
ac
k
o
ff
on
k
ey cy
li
n
d
er
(no more than one turn) until key is at the bottom. If key
cylinder has a logo (a), logo should be at the top of key
cylinder. a
KC9354/KC9354-2 INSTALLATION INSTRUCTIONS
Installing the KC9354/KC9354-2
57049-A Page 9 04-2007
8) Alignment of Interchangeable Cores:
9) Tighten the Four Screws in the Baseplate:
10) The Dead Latch’s “Critical Edge:”
• I
f
an I
C
C
ore
i
s use
d
, center t
h
e
i
nter
f
ace towar
d
t
h
e
bottom.
• T
i
g
h
ten t
h
e
f
our
b
asep
l
ate screws
i
n t
h
e
f
o
l
-
lowing order:
> Tighten aand buntil snug.
> Tighten c and duntil snug.
> Fully tighten aand b.
> Fully tighten cand d.
> Check all four screws to make sure that
all four are completely tight.
b
c
a
d
• For c
l
ar
i
ty purposes on
l
y, p
h
oto on t
h
e r
i
g
h
t
i
s
a view of deadlatch with escutcheon removed.
• Edge (a) is referred to as the dead latch’s
“critical edge.”
IMPORTANT: In the next step, the “critical edge” on
deadlatch will have to be lined up with hole (b) in
baseplate. See Position the Dead Latch’s Set Screw
Hole: on page 10
a
b
KC9354/KC9354-2 INSTALLATION INSTRUCTIONS
Installing the KC9354/KC9354-2
57049-A Page 10 04-2007
11) Position the Dead Latch’s Set Screw Hole:
• T
il
t t
h
e tr
i
m unt
il
you see t
h
e
“
cr
i
t
i
ca
l
edge” align with the larger hole in the
baseplate as shown in photo on right.
Look closely at edge of dead latch’s
“critical edge” (a) when doing this.
IMPORTANT: When the dead latch’s “critical
edge” is correctly aligned, the dead latch’s set
screw hole will likewise be correctly aligned.
Photos A, B and C below illustrate examples of an
incorrectly aligned critical edge. Photo D is an exam-
p
le of a correctly aligned critical edge.
a
NOT CORRECTLY
ALIGNED
NOT CORRECTLY
ALIGNED
NOT CORRECTLY
ALIGNED
CORRECTLY ALIGNED
ABC
D
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Schlage Tastenfeld Handbücher
