Schlagel EDI CONTROL 7 Bedienungsanleitung

SCHLAGEL, INC.

EDI Distributor Control 7

Page 1 of 1

New Features

 Smaller size 10x8x5

 Water and dust tight

 Menu system for customizing

 Automated configuration

 Integrated Terminal/ ontrol

 Spout Directory eliminates charts

 Easly to add a second control point

 Automated Sensor diagnostics

 Front panel Reset button

This manual describes the functions of the Keypad and Menu System. An explanation of the

Error odes including the cause and possible remedy is also included.

See the 7 Quick Install Manual for wiring and initial setup of the distributor.

EDI CONTROL 7

OPERATORS MANUAL

SCHLAGEL, INC.

EDI Distributor Control 7

Page 2 of 2

Key Pad Layout

Performes a re-boot of the C7 control.

Allows access to the menu of special functions to customize the display or perform special

operations. Use repeted presses on this key to scroll through the Menu system. Access the

function with the number shown.

hows a list of all of the named positions of the distributor and the access number (and F-Key

if set) used to move to that position. A valuable function to eliminate using a crossover chart.

Use repeted presses on this key to scroll through the directory, 4 positions at a time.

Power on LED.

A steady blue LED confirming the spout is in position and there are no errors. This LED will

blink rapidly if certain errors occur.

ix speed dial keys (F1 – F6) can be set to access any position with a single key press.

The ESCAPE key is used to erase any missed-typed numbers when attempting to move to

another position. It also is used to abandon a Menu operation.

Used to allow alphetical characters to be typed in the Menu system when assigning names to

a position. A single SHIFT press will use the upper left character shown on a key and a double

press will use the upper right character.

LEDs showing the current status of the sensors on the distributor.

SCHLAGEL, INC.

EDI Distributor Control

Page 3 of 3

MENU SYSTEM*

CUSTOMIZE DISPLAY

Edit Access

Numbers

Change the number used to access a position. (Numbers 1 – 255 are allowed.)

Access keys by default are 1 through the number of ducts on the distributor. Use

this if you would prefer to use a number with a special meaning.

Edit Position

Names

1,2

Rename each spout position, e.g., PO ITION 5 to WET CORN BIN.

Edit Function

Keys

Assign a peed Dial key (F1-F6) to frequently used positions.

Edit Caption

Change the name of the distributor as displayed on the top line.

MISC SETTIN S

Network

Functions

For network automation. tart/stop and assign name.

AutoRun

Testing

Used by technicians for proof of operation.

AutoTune

Routine

Used by technicians to reset spout-centering values.

INSTALL/SETUP

Run Motor

Manually

Used by technicians to check motor and spout movement.

Check ensors Used by technicians to check wiring and condition of the sensors..

Auto Install

Distributor

Used by technicians to configure the C7 to the distributor.

Notes

haded routines affect the operation of the distributor and should only be used by those familiar with

the results of its use.

These names are shown when using the SPOUT DIRECTORY.

Alphabetic characters require the use of the SHIFT key. Use a single or double shift to access the

left or right character of the key respectivally.

*Only the INSTALL/SETUP menu is available at boot.

SCHLAGEL, INC.

EDI Distributor Control 7

Page 4 of 4

ERROR MESSA ES

The C7 control continuously monitors the distributor for abnormal behavior and will notify the

operator when a detectable error occurs. The notification is displayed on Line 2 of the display.

Optional audible or visual alarms are available. Connected PLCs or other automation equipment

are also notified of the error.

Error Msg Reason Cause & Remedy

DRIVE

ERROR

The control has attempted to

move the spout but has not

received any feedback that it

is moving. If it does not

receive feedback for 10

seconds, the control will turn

off the motor and display this

error message.

The spout is jammed, the clutch is

slipping or the sensor circuit is not

functioning.

This is a fatal error. Press Enter to

reset the control. This is almost

always a mechanical obstruction at

the distributor.

POSITIONING

ERR

When the control was

positioning the spout over a

duct, it was not able to set it

to the exact predetermined

position.

omething has electrically or

mechanically disturbed the spout

position over the duct.

The alarms are set and operator

notified. Try accessing this position

again. Repeated errors indicate

action is required to repair the

problem. Check for a loose clutch or

loose drive chains in the drive

assembly.

SPO T

MOVED

This error message indicates

that the spout has been

moved out of position after a

successful stop. The C7

Control continuously monitor

spout position and raise this

alarm if the spout moves out

of position.

omething has electrically or

mechanically disturbed the spout

position over the duct.

This is a fatal error. Press Enter and

the control will return to the reset

screen. Check for a loose clutch or

loose bolts on the drive wheel or

drive arm assemblies.

SENSOR

ERROR

While the control is moving

the spout it continuously

anticipates the next code it

will encounter. If the next

code does not match the

anticipated code, the control

will attempt to re-read it up to

3 times. If it fails on the 3rd

try, the control will issue this

error.

An improperly positioned sensor

block in the distributor usually

causes this error.

This is a fatal error. Press Enter and

the control will return to the reset

screen. Position and shim the sensor

block properly. Run the Check

ensors routine.

Dieses Handbuch passt für folgende Modelle

Andere Schlagel Bedienfeld Handbücher

Schlagel

Schlagel VGC-V2 Leitfaden

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten