Schwinn 4IIII Handbuch

INSTALL

MANUAL

CORE HEALTH & FITNESS

4IIII POWERMETER

Page 1

1. Use a small phillips screwdriver to remove the

screw securing the battery cover, remove the

battery cover, then install the batteries. Once

the batteries are installed, replace the cover

and screw.

Fig. 1

2. Ensure that the rider’s right crank arm is at

the 6 o’clock position then push the crank

onto the bottom bracket at the 12 o’clock

position. Finally, using a torque wrench with

an 8mm allen socket attached, torque the

crank bolt to 40-44 ft-lb (55-60 Nm).

Fig. 2

3. Install the pedal into the crank arm then use

a torque wrench and a 8mm allen socket

to torque to the pedal bolt according to the

speciﬁcations below:

Threaded Pedal: 25-30 ft-lb (34-40 Nm)

Morse Taper Pedal: 33 -37 ft-lb (45-50 Nm)

NOTE: The pedal MUST be torqued to the above

speciﬁcations otherwise a failure of the pedal may

occur.

Fig. 3

Page 2

4. Ensure that the 4iiii crank is up to date. To do

this, check that Bluetooth is enabled on the

phone then follow the proceeding directions.

Fig. 4

5. Download the 4iiii app from the appropriate

app store BUT DO NOT CREATE A LOGIN.

Android

Fig. 5

iOS

Fig. 6

Page 3

6. Record the ANT+ ID of the powermeter that

needs to be updated.

NOTE: The ANT+ ID is a 4 OR 5 digit number

located on the underside of the 4iiii sensor. If the

number is 4 digits, the ﬁrst number of the ANT+

ID is zero (0).

Fig. 7

7. Open the 4iiii app and initiate a crank arm

scan by tapping on the icon in the lower left

corner.

Fig. 8

Page 4

8. Spin the 4iiii crank arm of the target bike >30

RPM; the 2-5 digit ANT+ ID should show up

on the “Bluetooth Scan” screen.

9. Tap on the checkmark to select the crank arm

then tap on “Connect”.

Fig. 9

10. After connecting to the crank arm, open the

settings menu.

Fig. 10

Page 5

11. On the “Device Settings” screen, select

“Update Features” if available.

Fig. 11

12. On the Echelon2G console, press and hold

STAGE and “AVG/MAX” for 3-5 seconds

to access the service menu.

13. Use AVG/MAX to scroll until SENSOR TYPE

is displayed then push the back-light button

to access the sensor menu. Ensure that

“4iiii” is displayed as the sensor type.

14. If the sensor type is set to “Echelon 2” press

the back-light button to select the sensor

type, use the AVG/MAX button to select “4iiii”

then press the back-light button again.

Page 6

15. Once “4iiii” is selected the console will enter

the pairing process, check the side of the

power sensor for a 4 OR* 5-digit ANT+ ID

code. Enter this code on the “ENTER ANT

ID” screen using AVG/MAX to scroll and the

back-light to enter the ANT+ ID.

Fig. 12 Fig. 13

Please note that the ANT+ ID referenced

in Step 4 could be either a 4-digit OR 5-digit

number.

If the 4-digit code is present, the ﬁrst number

of the ANT+ ID Code is zero (0).

16. Once the ANT+ ID has been entered, pedal

the bike, then select “PAIRING SPIN CRANK”

but pushing the back-light button . If

pairing does not pass, check to ensure the

ANT+ ID is correct and try the pairing process

again. It may take 2-3 attempts to pair

successfully.

17. After successfully pairing the 4iiii crank, the

power sensor must be calibrated BEFORE

riding the bike. Press and hold STAGE

and AVG/MAX for 3-5 seconds to access

the service menu then use AVG/MAX to

scroll until “CALIBRATE” is displayed

then select it using the back-light button

. “ZERO RESET” will be displayed,

press the back-light button to select it.

Once “SPINCRANK” is displayed, spin the

crank and press the back-light button

to proceed. Ensure that the left crank arm

is in the 6 o’clock position then follow the

on-screen directions to ﬁnish calibrating the

sensor.

trademarks of Nautilus Inc. used under license to Core Health & Fitness LLC. Throwdown is a registered trademark of Throwdown Industries, LLC.

Inhaltsverzeichnis

Andere Schwinn Fitness Electronic Handbücher

Schwinn

Schwinn MPower Echelon2G Bedienungsanleitung

Schwinn

Schwinn MPower Echelon2G Referenzhandbuch

Schwinn

Schwinn MPower Echelon2 Power Upgrade Bedienungsanleitung

Schwinn

Schwinn Echelon Console Bedienungsanleitung

Schwinn

Schwinn MPower Echelon2G Bedienungsanleitung

Schwinn

Schwinn MPower Console V2 Bedienungsanleitung

Schwinn

Schwinn MPower Echelon2 Power Upgrade Bedienungsanleitung

Schwinn

Schwinn MPower Echelon2 Power Upgrade Gebrauchs- und Pflegehandbuch

Schwinn

Schwinn MPower Bedienungsanleitung

Schwinn

Schwinn MPower Echelon2 Power Upgrade Installationsanleitung

Schwinn

Schwinn MPower Console V2 Bedienungsanleitung

Beliebte Fitness Electronic Handbücher anderer Marken

Tunturi

Tunturi Platinum Pro Bedienungsanleitung

ergoline

ergoline ergoselect 150 Bedienungsanleitung

Kettler

Kettler SM3635-68 Bedienungsanleitung

BH FITNESS

BH FITNESS G6424i Bedienungsanleitung

BodyMedia

BodyMedia DD100 Bedienungsanleitung

Octane Fitness

Octane Fitness ZERO RUNNER ZR7000 Handbuch

New Balance

New Balance EX2 900 Bedienungsanleitung

Energetics

Energetics PR 3000p Bedienungsanleitung

Sportline

Sportline Solo 910 Bedienungsanleitung

Suunto

Suunto T6D Bedienungsanleitung

Tacx

Tacx Bushido T1980 Bedienungsanleitung

BingoFit

BingoFit 907HR Bedienungsanleitung

Omron

Omron HJ-303 Bedienungsanleitung

OXYLANE

OXYLANE ONmove 200 GPS Bedienungsanleitung

BH FITNESS

BH FITNESS G2376D Bedienungsanleitung

pivotal

pivotal tracker 1 Bedienungsanleitung

Oregon Scientific

Oregon Scientific ECG Monitor SE332 Bedienungsanleitung

Wintec

Wintec Easy Band Bedienungsanleitung