Schwinn MPower Echelon2 Power Upgrade Bedienungsanleitung

MPower

™

Echelon2 Console

MPower

™

Echelon2 Power Upgrade

MPower

™

Echelon2 External Wiring Kit

Installation Guide

2 | P a g e M P o w e r E c h e l o n 2 I n s t a l l a t i o n G u i d e

Table of Contents

Introduction ................................................................................................................... 3

Tools Required.............................................................................................................. 3

Console Kit Contents.................................................................................................... 4

Optional Power Upgrade Kit Contents........................................................................ 4

External Wiring Kit Contents........................................................................................ 4

Console Installation on AC Sport and AC Performance............................................ 5

Optional Power Upgrade Kit Installation on AC Sport and AC Performance......... 11

Console Installation on AC Performance Plus ......................................................... 14

Optional Power Upgrade Kit Installation on AC Performance Plus........................ 20

Service Mode Operation............................................................................................. 23

Assigning System Settings........................................................................................ 24

Calibrating Power Sensor........................................................................................... 27

Checking System Settings, Resetting System, and Updating firmware................. 28

3 | P a g e M P o w e r E c h e l o n 2 I n s t a l l a t i o n G u i d e

INTRODUCTION

This installation guide details how to install and setup the following:

Schwinn MPower™ Echelon2 Console, P/N 740-8727

Schwinn MPower™ Echelon2 Optional Power Upgrade, P/N 740-8730

Schwinn MPower™ Echelon2 External Wiring Kit, P/N 740-8875

The following instructions apply to the following models:

Schwinn AC™ Performance

Schwinn AC™ Sport

Schwinn AC™ Sport with Carbon Blue

Schwinn AC™ Performance Plus

Schwinn AC™ Performance Plus with Carbon Blue

NOTE: The console cable must be externally routed on the AC Performance and AC

Sport models. This requires that the External Wiring Kit, 740-8875 be used. The

console cable for the AC Performance Plus is routed internally

TOOLS REQUIRED

Phillips screw driver

2.5mm hex key

3mm hex key

Long nose pliers

NOTE: Tools are not included in the kits.

4 | P a g e M P o w e r E c h e l o n 2 I n s t a l l a t i o n G u i d e

CONSOLE KIT CONTENTS

Item

Description

QTY

Console

Console mount bracket

RPM (Cadence) sensor

RPM sensor adapter for AC Sport and AC Performance models

Console-to-RPM sensor cable (Only used when the optional power upgrade

kit is not installed)

Connector protective cap

Cosmetic cap for AC Performance Plus models

C Cell Batteries

Console bracket mount screws, M4 x 10mm PHP, for AC Performance Plus

models

Console bracket mount screws, M5 x 14mm BHCS, for AC Sport and AC

Performance models

Connector protective cap mount screws, M3 x 12mm SHCS

Console-to-bracket mount screw, M3 x 6mm PHP

RPM sensor adapter mount screw, M3 x 6mm PHP (Only used on AC Sport

and AC Performance Plus models)

Cosmetic cap mount screw, M5 x 14mm (Same as Item 10)

Cable grommet

RPM cable saddles

Cable saddle mount rivets

CD Rom with Owner’s Manual and Installation Guide

OPTIONAL POWER UPGRADE KIT CONTENTS

Item

Description

QTY

Sensor assembly

Console-to-power sensor cable

RPM-to-Power sensor cable

Magnet assembly

Sensor mount screws, M4 x 6mm BHCS (Only 2 screws are used on older

models with two screw mount holes)

Calibration tool

EXTERNAL WIRE KIT CONTENTS

Item

Description

QTY

Cable duct assemblies

5 | P a g e M P o w e r E c h e l o n 2 I n s t a l l a t i o n G u i d e

CONSOLE INSTALLATION ON AC SPORT AND AC PERFORMANCE BIKES

1. Insert batteries into console. (Figure 1)

Figure 1

2. Mount the console bracket using the two (2) M5 x 14mm button head screws. Tighten the

screws using the 3mm hex key. (Figure 2 and Figure 3)

Figure 2

Figure 3

3. Slide the console onto the bracket. Insert the M3 x 6mm pan head screw and tighten with

the screw driver. (Figure 4)

6 | P a g e M P o w e r E c h e l o n 2 I n s t a l l a t i o n G u i d e

Figure 4

4. Prior to installing the upper conduit, clean head tube with isopropyl alcohol. Allow to air dry.

5. Peel off backing adhesive and align duct part number 740-8875-001 to forward edge and

lower edge of the frame tube (as shown below). Apply normal pressure for 5 seconds.

(Figure 5)

Note: It is recommended that the adhesive set for 24 hours before use.

6. Insert the cable through the slot. (Figure 5)

7. Snap the outer part of the cable duct onto the base with the cable inside. (Figure 6)

Figure 5

Figure 6

8. Using a Philips screw driver, remove the sweat guard (Do not use a power drill in removing

and re-installing). (Figure 7)

9. Route the cable through the sweat guard. (Figure 8)

7 | P a g e M P o w e r E c h e l o n 2 I n s t a l l a t i o n G u i d e

Figure 7

Figure 8

10. Re-mount the sweat guard. (Figure 9 and Figure 10)

Figure 9

Figure 10

11. Plug the console cable RJ45 connector into the console. (Figure 11)

12. Slide the grommet of the cable into the slot on the connector protective cap as shown.

(Figure 11)

13. Attach the protective cap to the bracket using the two (2) M3 x 12mm socket head cap

screws, and tighten with the 2.5mm hex key. (Figure 12)

8 | P a g e M P o w e r E c h e l o n 2 I n s t a l l a t i o n G u i d e

Figure 11

Figure 12

14. Attach the RPM sensor adapter to the RPM sensor using the M3 x 6mm Philips Pan Head

Screw. (Figure 13)

15. Unscrew the M3 x 6mm Philips Pan Head screw holding the RPM sensor cover on and

remove it. (Figure 14 and Figure 15)

Figure 13

Figure 14

Figure 15

9 | P a g e M P o w e r E c h e l o n 2 I n s t a l l a t i o n G u i d e

16. Plug the RPM sensor cable 2-pin connector into the RPM sensor connector and slide the

cable grommet into the slot in the RPM sensor housing. (Figure 16 and Figure 17)

17. Reinstall the RPM sensor cover into the housing, and reinstall the M3 x 6mm Philips Pan

Head screw. (Figure 18 and Figure 19)

Figure 16

Figure 17

Figure 18

Figure 19

18. Remove the top and bottom screw from the front of the chain guard. (Figure 20)

19. Position the RPM sensor as shown and reinstall the two chain guard screws. The RPM

sensor should be about 2 - 3mm away from the flywheel, or about the width of a credit card.

If the RPM sensor is too close, it will rub against the sensor magnet that is embedded in the

flywheel. If the RPM sensor is too far away, the sensor will intermittently pick up a signal

from the magnet or will not pick up any signal at all; this will cause an erratic RPM display, or

no RPM display. (Figure 21)

10 | P a g e M P o w e r E c h e l o n 2 I n s t a l l a t i o n G u i d e

Figure 20

Figure 21

20. Prior to applying the lower conduit, clean the surface of the inner right fork with isopropyl

alcohol and allow to air dry. Peel the non-stick strip off the plastic conduit base. Place it

firmly on the inside of the right hand fork. There should be about one inch gap between

chain guard/rpm sensor bracket and the wire conduit. (Figure 22)

21. Route the wire inside the conduit and snap the conduit outer cover on to the base.

(Figure 23 and Figure 24)

Figure 22

Figure 23

Figure 24

Andere Handbücher für MPower Echelon2 Power Upgrade

Inhaltsverzeichnis

Andere Schwinn Fitness Electronic Handbücher

Schwinn

Schwinn Echelon Console Bedienungsanleitung

Schwinn

Schwinn MPower Echelon2 Power Upgrade Bedienungsanleitung

Schwinn

Schwinn MPower Console V2 Bedienungsanleitung

Schwinn

Schwinn MPower Echelon2 Power Upgrade Installationsanleitung

Schwinn

Schwinn MPower Echelon2G Referenzhandbuch

Schwinn

Schwinn MPower Echelon2G Bedienungsanleitung

Schwinn

Schwinn MPower Bedienungsanleitung

Schwinn

Schwinn 4IIII Handbuch

Schwinn

Schwinn MPower Echelon2 Power Upgrade Gebrauchs- und Pflegehandbuch

Schwinn

Schwinn MPower Echelon2G Bedienungsanleitung

Schwinn

Schwinn MPower Console V2 Bedienungsanleitung

Beliebte Fitness Electronic Handbücher anderer Marken

Tunturi

Tunturi Platinum Pro Bedienungsanleitung

ergoline

ergoline ergoselect 150 Bedienungsanleitung

Kettler

Kettler SM3635-68 Bedienungsanleitung

BH FITNESS

BH FITNESS G6424i Bedienungsanleitung

BodyMedia

BodyMedia DD100 Bedienungsanleitung

Octane Fitness

Octane Fitness ZERO RUNNER ZR7000 Handbuch

New Balance

New Balance EX2 900 Bedienungsanleitung

Energetics

Energetics PR 3000p Bedienungsanleitung

Sportline

Sportline Solo 910 Bedienungsanleitung

Suunto

Suunto T6D Bedienungsanleitung

Tacx

Tacx Bushido T1980 Bedienungsanleitung

BingoFit

BingoFit 907HR Bedienungsanleitung

Omron

Omron HJ-303 Bedienungsanleitung

OXYLANE

OXYLANE ONmove 200 GPS Bedienungsanleitung

BH FITNESS

BH FITNESS G2376D Bedienungsanleitung

pivotal

pivotal tracker 1 Bedienungsanleitung

Oregon Scientific

Oregon Scientific ECG Monitor SE332 Bedienungsanleitung

Wintec

Wintec Easy Band Bedienungsanleitung