ScienTECH 6205SB Bedienungsanleitung
Scientech 6205SB IoT Enabled Smart Building
`2
Scientech 6205 IoT Enabled Smart Building
Table of Contents
1. Introduction 4
2. Features 5
3. Technical Specifications 7
4. Scope of learning 9
5. Smart Sensor Gateway Node Details 10
6. Theory 19
7. Sensor hardware and connection details
8. Installing CH340G Driver
9. Installing Arduino Software
10. Configuration of IP Camera 29
11. Quick Guide
12. Assignments
●Assignment 1 48
To make a basic LED blink program using Arduino.
●Assignment 2 51
To make ADC and UART program in Arduino.
●Assignment 3 53
To Program for on board LCD.
●Assignment 4 55
Testing and understanding PIR sensor with relay light.
●Assignment 5 57
Testing and understanding temperature and humidity sensor.
●Assignment 6 59
Testing and understanding CO2sensor.
●Assignment 7 61
Testing and understanding LPG sensor with relay light.
●Assignment 8 63
Testing and understanding smoke sensor with relay light.
Scientech 6205SB IoT Enabled Smart Building
`3
●Assignment 9 65
●Assignment 10 67
To make a program to control lights of Scientech 6205SB using
RFID tags
●Assignment 11 69
To receive data string wirelessly from Scientech6205SB using
Zigbee and Display it in Serial Monitor of Arduino
●Assignment 12 71
To implement an Arduino program to collect the sensors data from
Smart Sensor Gateway and send it to free cloud using ESP8266.
13. Warranty 78
14. List of Accessories 79
Scientech 6205SB IoT Enabled Smart Building
`4
Safety Instructions
Read the following safety instructions carefully before operating the product.
To avoid any personal injury, or damage to the product, or any products connected to
it;
Do not operate the instrument if you suspect any damage within.
The instrument should be serviced by qualified personnel only.
For your Safety:
Use proper Mains cord : Use only the mains cord designed for this product.
Ensure that the mains cord is suitable for your
country.
Ground the Instrument : This product is grounded through the protective earth
conductor of the mains cord. To avoid electric shock
the grounding conductor must be connected to the
earth ground. Before making connections to the input
terminals, ensure that the instrument is properly
grounded.
Observe Terminal Ratings : To avoid fire or shock hazards, observe all ratings and
marks on the instrument.
Use only the proper Fuse : Use the fuse type and rating specified for this product.
Use in proper Atmosphere : Please refer to operating conditions given in the
manual.
1. Do not operate in wet / damp conditions.
2. Do not operate in an explosive atmosphere.
3. Keep the product dust free, clean and dry.
Scientech 6205SB IoT Enabled Smart Building
`5
Introduction
With advances in technology, there is a constant demand for improvement in standard
of living, security and energy efficiency. Every building be it residential, commercial
or industrial runs on some or the other form of energy, thus there is a need to reduce
and optimize this energy consumption. Efficient energy management not only reduces
consumption but also reduces energy costs.
Scientech 6205SB IoT Enabled Smart Building training setup is specially designed to
help understand the concept of smart buildings and how various sensors can be
deployed and their data can be used to generate events and trigger alarms. Scientech
smart building comes with various sensors. The data from these sensors can be used
to generate various events like switching on and off lights, triggering an alarm,
providing access to a user using RFID tags and readers. This product helps explore
various aspects of smart building intended to optimize energy usage and security.
Scientech 6205 Smart building complete set
Scientech 6205SB IoT Enabled Smart Building
`6
Features
●Platform to learn, explore, and develop IoT skills.
●Three floors with six blocks table top building structure.
●Each block of building with LED lights.
●Arduino software compatible hardware.
●LPG gas, smoke, fire, PIR, temperature, humidity, and CO2sensors.
●RFID module for access control application.
●Touch switch panel with 4 power sockets and bulb intensity control output.
●Wi-Fi camera interface.
●Battery smart sensor gateway for sensor connectivity.
●USB and zigbee connectivity for personal computer (PC) interface.
●Wi-Fi connectivity for cloud interface.
●Sensor gateway with color LCD display.
●Buzzer and input/output switch for testing.
●Wi-Fi connectivity and android app for field testing.
●eal time graph analysis on PC and mobile.
●10 din sockets for sensors and actuators interface.
●On board charging and protection circuit for battery.
●Signal test points and switch fault.
●Inbuilt voltmeter and ammeter.
●Compact tabletop ergonomic design.
●Ready experimental details.
●User friendly, self-explanatory system.
Scientech 6205SB IoT Enabled Smart Building
`7
Technical Specifications
Microcontroller : ATMega2560
Sensors and Actuator connector : 10nos.
Digital I/O Pins : 34
Analog Input Pins : 16
UART : 2 nos.
I2C : 1 no.
Switch faults : 30nos.
Test points : 30nos.
Power Supplies : 5V and 3.3V
Variable POT : 1 no (10K)
Switches : 3nos.
Digital Voltmeter and Ammeter : 0 - 25V/10A
Buzzer and LED : 1 no. each
Color LCD : 1.77 inch
Battery : 3.7V/4400mAh
USB : 2.0
Wi-Fi Module : 1no. (2.4GHz)
Zigbee Transceiver : 2nos. (2.4GHz/63mW)
Flash Memory : 256 KB of which 8 KB for bootloader
SRAM : 8 KB
EEPROM : 4 KB
Clock Speed : 16 MHz
Node operating voltage : 5V DC
Camera : Wi-Fi IP Camera
Touch Panel : 4 Switches, 1 Regulator
RFID Module with 5 cards : 125KHz
LPG Gas Sensor : MQ06
Smoke Sensor : MQ135
Fire Sensor : TTL
PIR Sensor : TTL
Temperature Sensor : 0 - 100 Degree Celsius
Humidity Sensor : 0 100 %RH
CO2Sensor : 0-2000ppm
Interconnection for modules : 2 mm patch cords and FRC cables
Power Supply : 110V - 260V AC, 50/60Hz
Weight : 3.5Kg (approximately)
Operating Conditions : 0-400C, 85% RH
Scientech 6205SB IoT Enabled Smart Building
`8
Smart Sensor Gateway Node Details
Scientech 6205SSG Smart Sensor Gateway is an all in one development platform for
embedded system and IoT with inbuilt Wi-Fi, XBee, LCD and USB for output of the
data as well as plenty of extra GPIO to interface sensors and actuators.
It has inbuilt microcontroller ATmega2560, 54 digital input/output pins (of which 15
can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a
USB connection, a power jack, an ICSP header, and a reset button.
It can be powered via the USB connection, Inbuilt Battery or with an external power
supply. The power source is selected automatically. The adapter can be connected by
plugging a USB Cable into the input of USB connector. Scientech6205SB has inbuilt
battery of 4400mah capacity and by switching on the power switch inbuilt booster
circuit will power the Scientech6205SB from battery.
The ATMega2560 used in Scientech 6205 SSG is a low-power CMOS 8-bit
microcontroller based on the AVR enhanced RISC architecture. By executing
powerful instructions in a single clock cycle, the ATmega2560 achieves throughputs
approaching 1 MIPS per MHz allowing the system designed to optimize power
consumption versus processing speed.
Note: To charge the battery power the system over USB port and keep the power
switch on. Maximum charging time is 5 hours and it has inbuilt battery charging and
protection circuit for low voltage.
Scientech 6205SB IoT Enabled Smart Building
`9
Programmable GPIO Pinouts:
Pins
GPIO
Description
Pin 1
A14
Analog Pin
Pin 2
D10
Analog Pin
Pin 3
D12
Digital Pin
Pin 4
D6
Digital Pin
Scientech 6205SB IoT Enabled Smart Building
`10
1. Potentiometer:
Scientech Smart Sensor Gateway comes with a built-in 10K Potentiometer.
2. Power Supplies and Ground
2.1 +5 V DC Supply:
Scientech Smart Sensor Gateway is provided with three (3) +5V power supply
pins that can be connected using patch cords.
2.2 +3.3V DC Supply:
Scientech Smart Sensor Gateway is provided with three (3) +3.3V power supply
pins that can be connected using patch cords.
2.3 GND:
Scientech Smart Sensor Gateway is provided with three GND (ground) pins that
can be connected using patch cords.
Inhaltsverzeichnis
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
