Scott VINYL ENCODER 10 Bedienungsanleitung

USER MANUAL

www.my-scott.com

DJX 100 TT / VINYL ENCODER 10

PROFESSIONAL USB TURNTABLE

GB-2

USER MANUAL

Vinyl Encoder 10

SAFETY INSTRUCTIONS

1. Read these Instructions.

2. Keep these Instructions.

3. Heed all Warnings.

4. Follow all Instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with the manufacture’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9. Do not try to bypass the safety purpose of the polarized plug. The wide blade is provided for your

safety. If the provided plug does not fit into your wall outlet, consult an electrician for replacement of

the obsolete outlet.

10. Prevent the power cord from being walked on or pinched particularly at plug, convenience

receptacles, and point where from the power cord is connected to the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or

sold with the apparatus. When a cart is used, exercise caution when moving the

cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of

time.

14. Refer all servicing to qualified service personnel. Serving is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled into

the apparatus or objects have fallen into it, the apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

15. The mains plug is used to unplug the device, so it must remain easily accessible.

WARNING

To reduce the risk of the fire or electric shock, do not expose this apparatus to rain or moisture.

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,

such as vases, shall be placed on the apparatus.

CAUTION

DO NOT OPEN

RISK OF ELECTRIC SHOCK

CAUTION: To reduce the risk of electric shock, do not remove any cover. No user-serviceable parts

inside.

Refer servicing to qualified service personnel only.

The lightning flash with an symbol within the equilateral triangle is intended to alert the use to the

presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock.

The exclamation mark within the equilateral triangle is intended to alert the user to the presence of

important operation and maintenance (servicing) instructions in the literature accompanying this

appliance.

CAUTION

To prevent any risk of electric shock, ensure that the blades of the polarized plug can be fully inserted,

in order to prevent blade exposure.

GB-3

UNPACKING THE BOX

Before you begin assembly, please be sure all parts and accessories have arrived intact. In order to

do so, please use the check list below:

* Instruction manual * RCA cable * Slipmat * Platter

* 45rpm adaptor * Headshell * AC cord * Counterweight

Note:

* Do not connect the AC power plug before assembly has been completed.

* Before turning the power on, make sure once again that all the connections and power voltage

settings are correct.

Always turn off the power when connecting or disconnecting

* Read this manual carefully before using the unit. Be sure to store the manual in a safe place for

future reference.

* Attach a stylus cartridge to the headshell before assembling the turntable unit.

1. Unpacking:

Carefully remove the main unit with the packaging material intact from the box. Remove the

packaging material once the unit has been removed from the shipping carton. Be sure to

identify all the accessories located in the packaging material.

2. 45 rpm adaptor

Locate and remove the 45 rpm adapter from the packaging material and place it in the cut out

designed for this purpose on the top of the main unit.

3. Turntable platter:

Remove the turntable platter from the packaging material and gently insert the platter into the

center spindle on the base of the turntable unit.

4. Drive hub:

Pull the belt to the lower side of the turntable over the drive hub.

5. Slipmat:

Remove the black slipmat from the packaging and place it on the platter.

6. Headshell:

Insert the headshell into the front end of the tone arm. While holding headshell firmly onto the front

end of the tone arm, turn the headshell locking nut counterclockwise to firmly secure the headshell

to the tone arm.

7. Counterweight:

GB-4

SET-UP

a. Remove the stylus protective cover, if necessary. Never touch the stylus tip during the

adjustment.

b. Lower the tonearm lever.

c. Release the tonearm clamp and release the tonearm from the arm rest.

d. Set the anti-skate adjustment to “0”.

e. Rotate the counterweight in either direction until the tonearm is perfectly balanced

horizontally (floats freely)

f. Return the tonearm to the arm rest and lock it in place.

g. Hold the counterweight stationary with one hand and rotate only the stylus pressure ring in

order to adjust the pressure: the centre line on the rear shaft of the tone arm should be

aligned with the number “0” on the stylus pressure ring.

h. Rotate the counterweight clockwise until the scale value corresponds to the recommend

stylus pressure.

Note: The recommended stylus pressure of the optional cartridge that may have been included

with your unit is 2 grams. For all other cartridge systems please refer to the manufactures

specifications included with the cartridge.

HEADSHELL AND CARTRIDGE ASSEMBLY:

When installing a cartridge, refer to the operating instructions of that cartridge. During installation,

attach the stylus protector to guard the stylus tip from damage.

Connect the headshell lead wires to the cartridge terminals. The terminals of cartridges and the

headshell lead wires are color-coded. Connect each lead wire to the cartridge terminals of the

same color.

White (L+) L CH (+)

Blue (L-) L CH (-)

Red (R+) R CH (+)

Green (R-) R CH (-)

CONNECTIONS:

Before connecting the unit it is advised that you also

consult the instruction manuals for your current

equipment.

Note: Be sure to turn off the equipment before you

make changes to the different connections.

1. Connect the power cord to an AC outlet.

2. Connect the RCA cable to the PHONO input

of your amplifier.

Output terminals Amplifier (Receiver)

L (White) L CH

R (Red) R CH

You can also use a line input by setting the phono/line switch at the rear of the turntable to line.

Se t t h e P H ONO/LINE

sw i t c h t o “LINE”

Se t t h e P H ONO/LINE

sw i t c h to “PHONO”

GB-5

CONTROL AND FUNCTIONS

1. USB PORT

USB record only for MP3 format.

2. PLATTER

3. START/STOP BUTTON

Press this button to start or stop the platter.

4. PHONO/LINE SWITCH

Switch the output to either Phono or Line level.

5. PLATTER SPEEDS

Used to select the desired speed.

* Press the “33” button to select the 33rpm speed.

* Press the “45” button to select the 45rpm speed.

6. RECORD/STOP BUTTON

Press the button to start recording and press again to stop recording.

7. HEADSHELL LOCKING NUT

Attach the headshell by inserting it into the front end of the tone arm, then turn the locking

nut clockwise.

8. PITCH SLIDER

Use this control to change the speed of the platter. When you move the PITCH SLIDER,

the PITCH indicator will not light up; it will only light up when the PITCH SLIDER is at the

central position (0%).

5 6 7

18 17

16 419

GB-6

9. S-SHAPED TONEARM

10. TONEARM CLAMP AND REST

Use this rest to clamp the tone arm in position during transportation.

11. MOTOR OFF/Reverse BUTTON

Press this button to select Reverse/Forward playback.

Press the button for more than 1second to switch the motor off, and the LED will be flash.

Press the button again for more than 1 second again to switch the motor back on

12. 45 RPM ADAPTOR

Place on center spindle for playing 7” records with large center holes.

13. TONEARM LEVER

Allows you to move the tone arm the up or down.

14. ANTI-SKATE BUTTON

When a record is playing, a force is generated drawing the stylus towards the center of the

record. This control compensates for that force. Set the anti-skate button to the same

value as the stylus pressure.

15. COUNTERWEIGHT

Use the counterweight to balance the tone arm and to adjust the stylus pressure.

16. PHONO/LINE OUTPUT

Connect the turntable to any phono or line level input, using the supplied RCA/RCA cable.

Be sure to set the phono/line switch to the right position.

17. AC VOLTAGE SELECTOR

Make sure the selector is set properly.

18. POWER SWITCH

This switch turns the power on or off.

19. POWER CORD CONNECTOR

Used to connect the included power cord.

OPERATIONS

1. Push power button to switch the turntable on.

2. Place a record on the turntable mat. When playing a 45 rpm record with a large center

hole, place the 45 rpm adapter on the center spindle.

3. Set the rotation speed (33/45 rpm) to match the record.

4. Release the arm clamp

5. Set the cueing lever to the up position.

6. Press the Start/Stop button and the turntable platter will start to rotate.

7. Move the tone arm over the desired groove.

8. Set the cueing lever to the down position, the tone arm will descend slowly onto the record

and play begins.

9. Adjust the pitch to a desirable speed, move the pitch control slider towards the “+” or “-“ to

adjust the speed.

10. To pause play, lift the tone arm using the cueing lever.

11. When play is finished, raise the cueing lever, move the tone arm to the arm-rest and

secure the tone arm with the arm clamp.

12. Press the Start/Stop button to stop the platter rotating.

13. Push the Power button to switch the turntable off.

GB-7

SPECIFICATIONS

TURNTABLE

Type 2-speed full manual

Motor DC motor

Driving method Belt drive

Turntable platter 330mm diameter, aluminum diecast

Speeds 33

1/3and 45 rpm

USB function USB REC. Function (only for MP3 format 192 kbps)

Wow and flutter Less than 0.2% WRMS (JIS WTD) with 33 1/3rpm

S/N ratio More than 55dB (DIN-B)

Pitch controls +/- 10%

Starting Time Less than 1 second with 33 1/3

Braking Time Less than 1 second with 33 1/3

Time for Speed Change Less than 1 second from 33 1/3to 45 rpm

Less than 1 second from 45 to 33 1/3rpm

TONEARM

Type Static balanced S-shaped tonearm with detachable headshell

Effective Arm Length 230.5mm

Phono Output Level 1.5~3.6mV at 1KHz 5cm/sec (HP-4005)

Line Output Level 90~216mV at 1KHz 5cm/sec (HP-4005)

Frequency Response 20Hz-20KHz

Channel Separation More than 15dB

Channel Balance Within 2.5dB at 1KHz

GENERAL

Power Supply AC115/230V, 60/50Hz

Power Consumption 9 Watt

Dimensions 449 (W) x 370 (D) x 145 (H) mm

Weight 3.8 Kg

NOTE: Specifications and design subject to possible modification without notice, due to

improvements.

Should you have any questions/doubts on operating the unit, please send an e-mail to djtech@first-

audio.com

DISPOSAL

Disposal of waste electrical & electronic equipment (applicable in the European Union and

other European countries with separate collection systems).

This symbol on the product or on its packaging indicates that this product must not be

treated as household waste. Instead it must be handed over to the applicable collection

point for the recycling of electrical and electronic equipment. By ensuring this product is

disposed of correctly, you will help prevent potential negative consequences for the

environment and human health, which could otherwise be caused by inappropriate waste

handling of this product. The recycling of materials will help to conserve natural resources.

For more detailed information about recycling of this product, please contact your local

authorities, your household waste disposal service or the shop where you purchased the

product.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Scott Drehscheibe Handbücher

Scott

Scott DJX 60 TT Bedienungsanleitung

Beliebte Drehscheibe Handbücher anderer Marken

Gemini

Gemini CDT-05 MKII Bedienungsanleitung

Rotel

Rotel RP-820 Bedienungsanleitung

Shuman

Shuman MC-250BT Bedienungsanleitung

Stanton

Stanton STR8-150 Bedienungsanleitung

Audio Technica

Audio Technica AT-LPW40WN Bedienungsanleitung

Crosley

Crosley McQueen CR7011-GY Bedienungsanleitung

Reloop

Reloop SMP-1 Bedienungsanleitung

auna

auna TT-Classic Plus Bedienungsanleitung

COMO AUDIO

COMO AUDIO Turntable Analog Bedienungsanleitung

Dual

Dual 1009 F Bedienungsanleitung

REED

REED Muse3C Bedienungsanleitung

AXIOMTEK

AXIOMTEK OPS883-H Series Bedienungsanleitung

Pioneer

Pioneer PL-71 Bedienungsanleitung

Vestax

Vestax PDX-a1 Bedienungsanleitung

Denon

Denon DP-400 Bedienungsanleitung

Dual

Dual 504 Bedienungsanleitung

Audio-Techica

Audio-Techica AT-LP60XBT Bedienungsanleitung

Goldring

Goldring G99 Bedienungsanleitung