Seada SWMP Bedienungsanleitung

SWMP 4K Seamless Modular

Video Wall Matrix Switchers

User Guide

Document No. SD-MA-039

Document Version: 01

SWMP Matrix Switcher User Guide

Table of Contents

1. Product Introduction...................................................................................................................2

1.1. Product profile........................................................................................................................2

1.2. Product capability...................................................................................................................2

1.3. Specification & Parameters....................................................................................................3

2. Hardware Overview (2U)............................................................................................................4

2.1. Front Panel .............................................................................................................................4

2.2. Rear Panel (2U).......................................................................................................................4

3. Connection Set up........................................................................................................................5

3.1. RS232 connection...................................................................................................................5

3.2. Ethernet Connection ..............................................................................................................5

4. SWMP Software User Guide......................................................................................................5

4.1. Matrix Switch .........................................................................................................................7

4.2. Signal setting ..........................................................................................................................9

4.3. PQ & Position........................................................................................................................10

4.4. OSD Control ..........................................................................................................................11

4.5. Video Wall ............................................................................................................................12

4.6. Network Setting ...................................................................................................................14

5. Remote Control..........................................................................................................................15

5.1. Output/Input Buttons..........................................................................................................15

5.2. Function Buttons ..................................................................................................................15

6. SWMP ASCII Command Lines ..................................................................................................16

6.1. Video switching ....................................................................................................................16

6.2. Save Video Wall/Matrix Preset Layout ...............................................................................16

6.3. Load Video Wall/Matrix Preset Layout ...............................................................................16

SWMP Matrix Switcher User Guide

1. Product Introduction

1.1. Product profile

•SWMP multi format 4K Seamless Modular Video Wall Matrix Switcher is a high-

performance video signal switching equipment, can support up to 80 inputs, 80

outputs, with inserting plate structure. This product supports multiple video formats

input and output, switching, without disturbing the other output, high performance

output.

•Multi format matrix using the insert plate structure, flexible and convenient

installation. Support UHD-HDMI, 4K HDBaseT, 4K Fiber Optica, HDMI, DVI-U, SDI and

VGA input/output daughter cards. At the same time, with the Ethernet and RS232

communication interface, through the special control software to control the matrix

signal switching, monitoring the working state of the matrix, set the signal resolution,

etc.

•DVI-U daughter card support HDMI/DVI/VGA/YPbPr/CVBS signal with different

terminal adapters

So, for an HDMI signal, we can use HDMI card directly or DVI-U card, for VGA

signal, we can use VGA (DB15 interface) card directly or DVI-U card

•Seamless switching available.

•Video wall function available.

•OSD function: Font / colour / size control available

1.2. Product capability

•Support HDBaseT, HDMI, DVI-U, SDI, VGA, UHD-HDMI, Fiber Optic cards.

•Support a maximum resolution of 1600 x 1200@60hz with normal card.

•Support a maximum resolution of 3840 x 2160@60hz with 4K card.

•Provide a variety of control interface: RS232, Ethernet, WebUI.

•Provide control software to facilitate remote control, real-time display the input and

output status.

•Scalar inside, output resolution control available.

•Support Seamless switching, Character overlay, Video Wall function.

SWMP Matrix Switcher User Guide

1.3. Specification & Parameters

1080P Input & Output cards

Input

Interface type

Signal

Format

DVI-U

HDMI

DVI

VGA

YPbPr

CVBS

HDMI / DVI / VGA:

800x600,1024x768,1280x768,1280x800,1280x1024,1360x768,1400x1050,1600

x1200,1920x1080

YPbPr: 576i50,720p50,720p60,1080i50,1080i60, 1080p50,1080p60

CVBS: PAL, NTSC

HDMI

Same as DVI-U (HDMI input)

VGA

Same as DVI-U (VGA input)

BNC

SDI

480i60,576i50,1080i60,1080i50,720p60,720p50,1080p24/25/30/50/60

RJ45

HDbaseT

Same as DVI-U (HDMI input)

Fiber

Single mode single Fiber, 1920x1080, up to 1.4Km or 20Km

Output

Interface type

Signal

Format

DVI-U

HDMI

DVI

VGA

YPbPr

CVBS

HDMI / DVI / VGA:

1024x768, 1280x1024, 1360x768, 1280x720, 1600x1200 ,1680x1050,

1920x1080

YPbPr: 1080p60, 720p60

CVBS: PAL, NTSC

HDMI

Same as DVI-U (HDMI output)

VGA

Same as DVI-U (VGA output)

BNC

SDI

576i50,480i59,720p50,720p60,1080i50,1080i59,1080i60,1080p24/25/29/30/50

/60

RJ45

HDbaseT

Same as DVI-U (HDMI output)

Fiber

Single mode single Fiber, 1920x1080, up to 1.4Km or 20Km

4K Input & Output Cards

Input

Interface type

Signal

Format

HDMI

Up to HDMI 2.0 4K 444@60Hz

RJ45

HDbaseT

4K@60Hz, works with HDbaseT seamless transmitter box.

Each card needs 24V external power supply to PoC up to 2 x HDBaseT TX

Fiber

4K@60Hz, works with Fiber seamless transmitter box.

Output

Interface type

Signal

Format

HDMI

Up to HDMI 2.0 4K 444@60Hz

RJ45

HDbaseT

4K@60Hz, works with HDbaseT seamless receiver box.

Each card needs 24V external power supply to PoC up to 2 x HDBaseT RX

Fiber

4K@60Hz, works with Fiber seamless receiver box.

Note: OSD function is not available on 4K cards.

Control -RS232

RS-232 Straight

D-sub-9

Baud rate：9600

Control -LAN

Static IP, Automatic IP

Power supply

AC100 - 240V 50/60Hz

Working temperature

32 - 104°F / 0 - 40°C

Storage temperature

-4 - 140°F / -20 - 60°C

Humidity

20 - 90% RH (no condensation)

8x8, 2U

16x16, 4U

36x36, 8U

80x80, 16U

Dimension

W*D*H

483x365x89mm

483x365x178mm

483x365x356mm

483x365x712mm

Gross weight

9Kg

13Kg

23Kg

44Kg

Power

Supply

100W * 2 (Redundant)

200W * 2(Redundant)

350W * 2(Redundant)

350W * 4(Redundant)

SWMP Matrix Switcher User Guide

2. Hardware Overview (2U)

2.1. Front Panel

•OUTPUT/INPUT Buttons

Press buttons OUTPUT x+ INPUT y+ ENTER in order, switch input xto output y.

•MENU Buttons

➢Press buttons ALL + INPUT x+ ENTER in order, to switch input xto all the outputs, users

can use this combination to switch between different inputs to the video wall

➢Press buttons SAVE + OUTPUT y+ ENTER to save current matrix/video wall layout as

layout y (Save up to 8 preset layouts using panel buttons)

➢Press buttons RECALL + OUTPUT y + ENTER in order, to recall layout y(Recall up to 8

preset layouts using panel buttons)

➢Press RESET button to cancel the current command function

➢Press LOCK button to lock all front panel buttons

➢ENTER button is an executive key

2.2. Rear Panel (2U)

•LAN(10M/100M/1000M) and RS232 Port are for PC control

•Input Ports

Up to 80 inputs (16U) of different formats (DVI, HDMI, SDI, HDBaseT and Fiber) with resolution up

to 4K@60

•Out Ports

Up to 80 inputs (16U) of different formats (DVI, HDMI, SDI, HDBaseT and Fiber) with resolution up

to 4K@60

•Power Supply Socket

110 ~ 240 VAC redundant power supplies

SWMP Matrix Switcher User Guide

3. Connection Set up

3.1. RS232 connection

RS-232 control, baud rate 9600, DB9 connector

3.2. Ethernet Connection

Connect the SWMP unit with the control PC using either CAT cable. Make sure the PC is in the same

group of static IP address as SWMP.

Left is the default IP setting of SWMP. Users can change the IP

address once connected.

4. SWMP Software User Guide

Users can run the SWMP.exe software directly without installation. Software is on the disk in the

package, or you can download it from the SEADA website. Double click the SWMP software to get the

Dialog box as below

Default password for Administrator:111111

Default password for User: 000000

Users can change the password here as well

1. Click drop-down list to select account: Administrator or User

2. Input current password, then click the ‘modify’ button to open the Modify password window

SWMP Matrix Switcher User Guide

Type in new password, then click the ‘modify’

button to change to the new password

Once log in, the following user interface will be shown on screen. The system will remember the last

connection setup and automatically try to connect the SWMP system. If not, please check 4.1.1 and

4.1.2 for how to connect the unit with control PC.

There are 6main tabs in this software to help users set up and control the SWMP matrix switcher.

SWMP Matrix Switcher User Guide

4.1. Matrix Switch

Users can connect the SWMP device to control PC and set up the device as matrix switcher in this

section.

4.1.1. Connect to the SWMP via RJ45 for RS232

Connect the SWMP to the control PC with a serial cable (a RS232 to USB cable is included in the

package)

If the software was connected via UART (RS232) last

time, software will connect to the SWMP

automatically vis RS232. If it was used at Network

last time, a ‘Network Timeout’ error message will be shown on screen and users need to set up as

below for RS232 connection in the software

•Choose ‘UART’ instead of ‘Network’

•Select the COM port from the Port dropdown menu

•Press ‘Disconnected’ button to connect

The software will check all the parts of the device. A ‘Read data succeeded’ dialog box will be shown

on screen when finished.

4.1.2. Connect to the SWMP via Network

The default IP address for SWMP matrix switcher is 192.168.0.247,Users need to change the IP

address of the control PC to the same network segment as the SWMP.

•Change the ‘Obtain an IP address automatically’ to ‘Use the following IP address’ to set up

a static IP address of TCP/IPv4 in Ethernet Properties

➢IP address: any address between 192.168.0.2 and 192.168.0.254 except the address which has

been taken by the SWMP

➢Subnet mask: 255.255.255.0, Default Gateway: 192.168.0.1

Connect the SWMP with a CAT cable to the

control PC (cable included in the package)

If the software was connected via Network

last time, software will connect to the SWMP

automatically via network. If it was used at

serial port last time, a ‘Please select COM

port’ error message will be shown on screen and users need to set up as below for Network connection

in the software

•Choose ‘Network’ instead of ‘UART’

•Press ‘Search Device’ button to find the SWMP on the network

•Highlight the device Press ‘Disconnected’ button to connect

4.1.3. Matrix Switch Routing

Users can switch and assign different inputs to the

selected outputs in the matrix. The name of the

input/output can also be changed by selecting the

default name –Input1/Output1 and replacing it

with the chosen name. Users need to disable the

video wall mode (Cancel the splicing, see 4.5.2) to

enable the matrix switcher mode.

SWMP Matrix Switcher User Guide

4.1.4. Allset, Recall, Save As, Reset, EDID and Switch UI

•The Allset dropdown menu helps the users select a single input to be displayed on all the

screens

•Recall: Recall a matrix switching preset layout. The device supports maximum 25 layouts.

•SaveAs: Save up to 25 preset layouts for matrix switching (same as video wall layouts, 4.5.3)

•Reset: Reset the unit to default factory configuration.

•EDID: Users can read the EDID from the output (from the receive device, such as screen) and

apply it to the input port

✓Read: read the EDID of the selected output

✓Save: save the displayed EDID after ‘Read’

✓Open: open an EDID from previous saved EDID

✓Write: write the current displayed EDID onto selected input

to customized input EDID

•Switch UI: users can switch UI style in this section to choose the best suitable UI for themselves.

SWMP Matrix Switcher User Guide

4.2. Signal setting

In the Signal Settings tab, users can use the ‘Read All’function button to recognize the type and

resolution automatically. Additionally, you can also manually read one Input/output at a time –

pressing the Read button next to the selected input will only read that input alone.

I. Input Type Shows the input video sources type (HDMI or DVI)

II. Input Format Shows the resolution of the input video sources

III. Audio Select

Auto: HDMI output embedded audio and analog audio output will get the

audio from the embedded audio of the HDMI input to be displayed on the

output channel. If the input source is DVI, the output system will get the

audio from the input analog audio

External: HDMI output embedded audio and analog audio output will get

the audio from the corresponding analog audio of the HDMI input to be displayed on the output

channel

IV. Output Type

Users can choose different output formats for certain output cards (e.g.,

HDMI output card can be used as DVI or HDMI, DVI output card can be used

as both digital and analog)

V. Output Format

Users can manually change the output resolution here to match the

requirement of the receiving side

Andere Handbücher für SWMP

Inhaltsverzeichnis

Andere Seada Matrix-Umschalter Handbücher

Seada

Seada MS-HDM88 Bedienungsanleitung

Seada

Seada SWM Series Bedienungsanleitung

Seada

Seada MS-HBT44B70 Bedienungsanleitung

Seada

Seada MS-HBTB66C70 KIT Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

Kramer

Kramer XL 3216VS Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

Kramer

Kramer VP-2x2 Bedienungsanleitung

Kramer

Kramer Sierra Video 6432V5xl Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte