SeaLevel DIO-32.PCIe Bedienungsanleitung

DIO-32.PCIe

User Manual | 8004e

Contents

CONTENTS...........................................................................................................................................................2

BEFORE YOU GET STARTED ...............................................................................................................................3

INTRODUCTION ................................................................................................................................................... 4

ELECTRICAL SPECIFICATIONS...........................................................................................................................6

TECHNICAL SPECIFICATIONS............................................................................................................................7

HARDWARE INSTALLATION ...............................................................................................................................8

PROGRAMMING THE DIO-32.PCI .....................................................................................................................11

EXAMPLE CIRCUITS ..........................................................................................................................................19

SOFTWARE INSTALLATION..............................................................................................................................20

APPENDIX A – HANDLING INSTRUCTIONS ....................................................................................................23

APPENDIX B – TROUBLESHOOTING................................................................................................................24

APPENDIX C – HOW TO GET ASSISTANCE.....................................................................................................27

APPENDIX D – DRAWING..................................................................................................................................28

APPENDIX E – COMPLIANCE NOTICES...........................................................................................................29

WARRANTY ........................................................................................................................................................30

Before You Get Started

What’s Included

The 8004e is shipped with the following items. If any of these items are missing or damaged, please contact

Sealevel for replacement.

•8004e - DIO-32.PCIe Digital I/O Adapter

o8004e – Board with 3-13 inputs

o8004He – Board with 10-30V inputs

•DB78 Maes to D37 Male and DB37 Female V-cable (Item# CA165)

Advisory Conventions

Warning

The highest level of importance used to stress a condition where damage could result to the

product, or the user could suffer serious injury.

Important

The middle level of importance used to highlight information that might not seem obvious or a

situation that could cause the product to fail.

Note

The lowest level of importance used to provide background information, additional tips, or other

non-critical facts that will not affect the use of the product.

Introduction

Overview

The DIO-32.PCIe digital I/O interface provides 16 optically isolated inputs and 16 reed relay outputs. The

inputs protect the PC and other sensitive equipment from spikes and ground loop current that can be

generated in industrial environments, while the outputs provide high quality, long life, low current (10 Watt

maximum), dry contact switch closures. Reed relays are well suited for low current applications. The relays

are normally open, and close when energized.

The SeaI/O Classic software drivers and utilities can be obtained from the Sealevel web site. They make

installation and operation easy using Windows 7, Vista, and XP operating systems. The SeaI/O API

(Application Programmer Interface) provides a variety of useful high-level function calls implemented as a

Windows dynamic link library (DLL) and as a Linux kernel module and library. SeaI/O also includes sample

code and utilities to simplify software development.

The inputs on the 8004e are rated for 3-13V. The inputs on the 8004He are rated for 10-30V.

Features

•PCI Express X1 compliant

•16 optically isolated inputs

•Socketed dip resistor allows user configurable input range up to +30V

•16 Reed relay outputs (SPST)

•Highly reliable 10VA Reed relays

•Power (+5V and +12V) and ground provided on DB78 board connector

•Includes 72” cable with DB78 Male connector to DB37 Male and DB37 Female connectors (Item#

CA165)

•SeaI/O Classic software supports Windows 7, Vista, and XP operating systems

•Software support for Linux available

Optional Items

Depending upon your application, you are likely to find one or more of the following items useful with the

8004e. All items can be purchased from our website (www.sealevel.com)by calling our sales team at (864)

843-4343.

Cables

DB37 Male to DB37 Female Extension Cable (Item# CA112)

This cable provides a 6’ extension to the CA165. It has one

DB37 Male connector and one DB37 Female connector.

DB78 Male to DB78 Female Extension Cable (Item# CA233)

This cable provides a 6’ extension to the DB78 board

connector on the 8004e. It has one DB78 Male connector and

one DB78 Female connector.

DB78M to DB37 Female and DB37 Male, for 3093 (Item# CA378)

The CA378 is designed specifically for customers using the

3093 ISA digital I/O board that need to upgrade to the 8004e

PCIe board while preserving existing infrastructure wiring. The

CA378 connects to the 8004e and provides an identical pin out

to the 3093.

Terminal Blocks

DB37 Terminal Block (Item# TB02)

Break out serial and digital connectors to screw terminals for

easy field connection. The TB02 terminal block is designed

with both DB37 male and female connectors for interfacing

the inputs or outputs.

Electrical Specifications

Features

•2 sets SPST relays with each having 8 relays

•2 eight bit input ports

•DB-37 Male connector for relay outputs

•DB-37 Female connector for optically isolated inputs

•Highly reliable 10 VA reed relays

•Multiple adapters can reside in same computer

Input Ports

Turn On Current 3mA

Isolator Diode Drop 1.1 VDC

Resistor Power Max .25 W

Maximum Input Range 3 – 13 VDC/VAC

Maximum Input Current 50 mA

Output Relays

Contact Max Power Rating 10 W

Contact Voltage Maximum 60 VDC (or peak VAC)

Contact Current Maximum .5A AC/DC RMS

Contact Resistance, Initial .15

Ω

Rated Life

Low Load 200 Million Closures

Maximum Load 100 Million Closures

Contact Speed

Operate .5 mS

Release .5 mS

Bounce .5 mS

Maximum Operating Speed 600 Hz

Technical Specifications

Physical Dimensions

Board length 6.5 inches (16.5 cm)

Board height 4.2 inches (10.7 cm)

Environmental Specifications

Specification Operating Storage

Temperature Range 0º to 70º C (32º to 158º F) -50º to 105º C (-58º to 221º F)

Humidity Range 10 to 90% R.H. Non-Condensing 10 to 90% R.H. Non-Condensing

Manufacturing

All Sealevel Systems Printed Circuit boards are built to UL 94V0 rating and are 100% electrically tested.

These printed circuit boards are solder mask over bare copper or solder mask over tin nickel.

Hardware Installation

Do not install the PCI Express board until the software has been fully installed.

The DIO-32.PCIe does not need to be configured prior to installation.

Once you have installed the SeaI/O Classic software, install the board into an available PCI Express slot

and boot the computer. The Found New Hardware wizard will appear. The drivers that were installed

during the software installation process will automatically be used to configure the adapter.

The following instructions are applicable to the Windows XP operating system and may vary depending

on your version of Windows.

1. After the software installation is complete, install the ISO-16.PCIe into an available PCI Express

slot and boot the computer.

2. A ‘Found New Hardware’ alert will appear above the system tray.

3. When the ‘Found New Hardware’ alert informs you that your hardware is installed and ready to use,

you can proceed with verifying the installation to check functionality if necessary.

Verifying Installation

To confirm that the digital I/O card has been successfully installed and recognized by your operating

system, look in the Windows Device Manager.

To access Device Manager, follow the steps below:

1. Right click on ‘My Computer’ icon on your desktop or in the Start menu.

2. Click ‘Manage’ in the fly out menu to launch the ‘Computer Management’ console window.

3. In the left pane under ‘System Tools’, click ‘Device Manager’.

4. In right pane near the bottom, expand the ‘SeaI/O Device’ section by clicking the ‘+’ symbol. This

shows the parent device is installed correctly.

5. You should see the card assignment listed as ‘SeaI/O 8004e’ with the card number in parentheses.

The card number will increment for each additional SeaI/O device installed.

The DIO-32.PCIe is now ready for use.

Digital I/O Interface

The DIO-32.PCIe provides four parallel input/output (I/O) ports. The ports are organized as ports A, B, C,

and D. Port A and B are input ports interfaced to optically-isolated inputs, while ports C and D are reed relay

output ports. Assuming an I/O address of 4000 Hex the following table shows the Port Addresses.

Base Address Hex Decimal Mode

Port A Address 4000 16384

Port B Address 4001 16385

Optically Isolated Input Port

Port C Address 4002 16386

Port D Address 4003 16387

Reed Relay Output Port

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SeaLevel Computerhardware Handbücher

SeaLevel

SeaLevel ACB-ULTRA.LPCI Bedienungsanleitung

SeaLevel

SeaLevel SeaISO ISO-1 Bedienungsanleitung

SeaLevel

SeaLevel SeaLINK DIN Rail USB Series Bedienungsanleitung

SeaLevel

SeaLevel 7406e Bedienungsanleitung

SeaLevel

SeaLevel PIO-48.PCI Bedienungsanleitung

SeaLevel

SeaLevel DuoCom Bedienungsanleitung

SeaLevel

SeaLevel SIO-104 Bedienungsanleitung

SeaLevel

SeaLevel SeaPORT REL-16 Bedienungsanleitung

SeaLevel

SeaLevel ULTRA COMM+8.PCIe Bedienungsanleitung

SeaLevel

SeaLevel SIO-104+2 Series Bedienungsanleitung

SeaLevel

SeaLevel SeaLINK+232.PC Bedienungsanleitung

SeaLevel

SeaLevel ACB-104 Bedienungsanleitung

SeaLevel

SeaLevel ISO COMM2.cPCI Bedienungsanleitung

SeaLevel

SeaLevel DIO-16.LPCIe Bedienungsanleitung

SeaLevel

SeaLevel ISO-16.PCI Bedienungsanleitung

SeaLevel

SeaLevel ACB-II/EX Bedienungsanleitung

SeaLevel

SeaLevel DIO-32B Bedienungsanleitung

SeaLevel

SeaLevel SEAI/OUSBSERIAL Bedienungsanleitung

SeaLevel

SeaLevel Ultra-SIO 3089 Bedienungsanleitung

SeaLevel

SeaLevel COMM+232.PCIe Bedienungsanleitung

SeaLevel

SeaLevel ISO-COMM Bedienungsanleitung

SeaLevel

SeaLevel SeaLINK+16/USB Bedienungsanleitung

SeaLevel

SeaLevel COMM+2 Bedienungsanleitung

SeaLevel

SeaLevel PCIO 4035 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung