Sealey MES01 Bedienungsanleitung
INSTRUCTIONS FOR
MOTORCYCLE ENGINE STAND -
SINGLE/TWIN CYLINDER
MODEL NO: MES01
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to when using this
equipment.
8DO NOT use unit if damaged.
9Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9Keep the stand clean for best and safest performance.
9Locate the stand in a suitable work area. Keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
9Use on a firm, level surface capable of sustaining the stand and the load.
9Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9Ensure all non-essential persons keep a safe distance whilst the stand is in use.
9Lock ratchet in position with locking pin before fixing a load and ensure the engine is centred and securely mounted.
9Ensure the stand and load are stable.
9DO NOT allow untrained persons to use the stand.
8DO NOT exceed the rated capacity of 30kg.
8DO NOT use the stand for purposes other than those for which it is designed.
9When not in use store stand in a safe, dry, childproof area.
2. INTRODUCTION
Suitable for a wide variety of engines and transmissions. Model no. MES01 is suitable for lower capacity single and twin cylinder engines
(maximum weight 30kg) and includes a utility/drip tray.
3. SPECIFICATION
Model no: .................................................................. MES01
Maximum capacity: ........................................................ 30kg
Height: ....................................................................... 375mm
Width:......................................................................... 320mm
Length:....................................................................... 535mm
Engine support span: .......................................... 200-375mm
ASSEMBLY
MES01 | Issue 1 03/12/15
Original Language Version
© Jack Sealey Limited
Refer to
Instruction
Manual
4. ASSEMBLY
4.1. Insertpost(24)intoxedframe(20),usebolt(22),
washer (11) and nut (23) to secure each end.
4.2. Fitmovableframe(2)toxedframe(20).
Fitratchetset(17)toxedframe(20).Usenut(19)and
nut (18) inside frame.
Usebolt(16)andsleeve(15)betweenxedframe(20)and
moveable frame (2), washer (14) and nut (13) at the ratchet
set end.
At the other end use bolt (21), sleeve (15) between the
two frames, washer (14) and nut (13).
4.3. Fitenginecradle(4)tomoveableframe(2)usingscrew(9)
washer (11) and nut (10).
Fit screw (5) into the other end of the engine cradle (4).
Use two nylock nuts (3) either side of the engine cradle.
Screw support tube (7) onto this. Use rod (8) through the
end, to tighten.
Fit screw (6) through the moveable frame in the same way
asscrew(5)wasxed.Screwonsupporttube(7).
4.4. Slide in oil plate (25).
4.5. Check all fasteners are secure.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Sole UK Distributor, Sealey Group.
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk.
IP32 7AR
www.sealey.co.uk
sales@sealey.co.uk
01284 757500
01284 703534
Web
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
MES01 | Issue 1 03/12/15
Original Language Version
© Jack Sealey Limited
Inhaltsverzeichnis
Andere Sealey Rack & Stand Handbücher
Sealey
Sealey AP6350.V3 Bedienungsanleitung
Sealey
Sealey ES900F.V2 Bedienungsanleitung
Sealey
Sealey ES750.V3 Bedienungsanleitung
Sealey
Sealey ES900F.V2 Bedienungsanleitung
Sealey
Sealey AS12.V2 Bedienungsanleitung
Sealey
Sealey APWSR01 Bedienungsanleitung
Sealey
Sealey RE55.V6 Bedienungsanleitung
Sealey
Sealey MES03 Bedienungsanleitung
Sealey
Sealey DRP15.V2 Bedienungsanleitung
Sealey
Sealey APTT Bedienungsanleitung
Sealey
Sealey VS301 Bedienungsanleitung
Sealey
Sealey AS10 Bedienungsanleitung
Sealey
Sealey AS6.V2 Series Bedienungsanleitung
Sealey
Sealey RE55.V6 Bedienungsanleitung
Sealey
Sealey API10 Bedienungsanleitung
Sealey
Sealey STR004.V3 Bedienungsanleitung
Sealey
Sealey AS2000F.V2 Bedienungsanleitung
Sealey
Sealey LC800ST Bedienungsanleitung
Sealey
Sealey VS2002.V4 Bedienungsanleitung
Sealey
Sealey AS15000 Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
