Sealey VS400 Bedienungsanleitung

INSTRUCTIONS FOR:

VACUUM SYSTEM TEST KIT

Model No: VS400

3Familiarise yourself with the applications and limitations, as well as any potential hazards, of the kit.

3Keep this product in good working order and condition (take immediate action to repair or replace damaged parts).

3Use approved parts only (unapproved parts may be dangerous and will invalidate the warranty).

3Wear approved eye protection. Contact your Sealey dealer for details.

3Keep children and unauthorised persons away from the work area.

3Keep work area clean and tidy and free from unrelated materials.

3Ensure the work area has adequate lighting.

7DO NOT use the kit to perform a task for which it is not designed.

7DO NOT allow untrained persons to use the kit.

7DO NOT use whilst under the influence of drugs, alcohol or intoxicating medication.

3After use, clean equipment, place in case and store in a cool, dry, childproof area.

3Dispose of waste liquids in accordance with local authority regulations.

pWARNING! DO NOT pollute the environment by allowing uncontrolled discharge of fluids.

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

IMPORTANT! PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS

AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE

TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.

2. CONTENT

1. SAFETY INSTRUCTIONS

Check the contents of the case against the list below. If any item is missing or damaged contact your supplier immediately.

A - Vacuum Gun and Gauge E - Sealing Lid (container) I - Tube End Cones x 6

B - Vented Cap F - Extension Tubes, 1/4ID x 2, 1/8ID x 2 J - Gun Cones x 2

C - 24 x !/4ID Tubing x2 G - Bleed Nipple Adaptors x 3 K - Tube Adaptor

D - Fluid Container H - Suction Cup L - Hose Cone

VS400 - 0021 - (1) - 181000

VS400 - 0021 - (!) - 181000

3. INTRODUCTION

The VS400 vacuum gun is capable of maintaining depressions of up to 25in(64cm)Hg and has a displacement of 1in3(16ml) per stroke.

Accessories are supplied to allow single handed brake and clutch bleeding, the testing of vacuum actuated switches and modulators and many

other applications.

4. APPLICATIONS

WARNING! Before use, ensure you read, understand and apply safety

instructions in Section 1.

Note:These instructions are of a general nature only. Always follow the specific

instructions in the vehicle manufacturers, or a proprietary, manual.

4.1. Vacuum gun

4.1.1. When using gun with outlet port ( fig.1.2) unconnected, protect it with vented cap (fig.1.B)

to prevent ingress of dirt.

4.1.2. At any time during use of the gun the vacuum generated may be released by pulling

trigger (fig.1.3).

4.2. Bleeding

WARNING! Familiarise yourself with the hazards of brake fluid - read manufacturers

instructions on container.

4.2.1. Fit appropriately sized adaptor (G) to the bleed nipple of the wheel brake (or clutch

actuating) cylinder.

4.2.2. Connect the adaptor to the vacuum port (fig.1.1) of the gun using tubing provided.

4.2.3. Connect outlet port (fig.1.2) of the gun to top of fluid container (port marked Pump)

with second length of tubing provided.

4.2.4. Ensure master cylinder reservoir level is above minimum and then unscrew bleed nipple

approx. 1/4 turn.

4.2.5. Operate vacuum gun to draw brake fluid through system and into fluid container.

DO NOT allow level in reservoir to fall below minimum. Check frequently and

refill as necessary with new fluid.

4.2.6. Continue until fluid entering container is clean and bubble-free. Retighten bleed nipple

and then remove adaptor.

4.2.7. After bleeding brakes always check that brake pedal feels firm and that brakes operate

normally, before going onto public roads.

4.3. General applications

Because the gun creates a partial vacuum it can be use to:

a) test the operation and calibration of any item which responds to a vacuum during normal operation e.g. ignition vacuum advance/retard mechanism.

b) check systems (fuel, air con., heating, brake servo etc.) for leakage.

c) test 2-stroke engines for crankcase seal leaks.

d) test pressure switches etc. if the vacuum pump can be connected to the atmospheric side of the component.

fig. 1

01284 757500 E-mail: sales@sealey.co.uk

01284 703534

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our catalogue and promotions call 01284 757525 and leave your full name and address, including postcode.

Sole UK Distributor,

Sealey Group, Bury St. Edmunds, Suffolk.

Inhaltsverzeichnis

Andere Sealey Prüfgeräte Handbücher

Sealey

Sealey HBS97.V2 Bedienungsanleitung

Sealey

Sealey BT91/7.V4 Bedienungsanleitung

Sealey

Sealey BT2014 Bedienungsanleitung

Sealey

Sealey BT01 Bedienungsanleitung

Sealey

Sealey VS0014 Bedienungsanleitung

Sealey

Sealey VS027.V2 Bedienungsanleitung

Sealey

Sealey VS001.V3 Bedienungsanleitung

Sealey

Sealey VSE2020.V3 Bedienungsanleitung

Sealey

Sealey BT91/10.V3 Bedienungsanleitung

Sealey

Sealey TA319 Bedienungsanleitung

Sealey

Sealey VSE2020.V2 Bedienungsanleitung

Sealey

Sealey VS0012 Bedienungsanleitung

Sealey

Sealey BT91/11 Bedienungsanleitung

Sealey

Sealey Auto Service VS0271 Bedienungsanleitung

Sealey

Sealey VS2058.V3 Bedienungsanleitung

Sealey

Sealey TA131 Bedienungsanleitung

Sealey

Sealey BT103 Bedienungsanleitung

Sealey

Sealey VSE300D Bedienungsanleitung

Sealey

Sealey Auto Service BT91D.V2 Bedienungsanleitung

Sealey

Sealey CV0011 Bedienungsanleitung

Sealey

Sealey VS2058.V2 Bedienungsanleitung

Sealey

Sealey BT2101 Bedienungsanleitung

Sealey

Sealey Auto Service Line VS2030 Bedienungsanleitung

Sealey

Sealey VS2030.V2 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung