Sealey AP12600 Bedienungsanleitung

INSTRUCTIONS FOR:

1.2 METRE WORKBENCH WITH DRAWER

MODEL:AP12600

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

2. CONTENTS

1.1 GENERAL SAFETY

!WARNING! Ensure Health & Safety, local authority, and general workshop practice

regulations are adhered to when using this bench.

"Locate bench in a suitable work area.

"Keep the work area clean, uncluttered and ensure there is adequate lighting.

!WARNING! Use bench on level and solid ground, preferably concrete.

"Keep the bench clean and tidy in accordance with good workshop practice.

"Keep children and unauthorised persons away from the work area.

#DO NOT use the bench for any purpose other than that for which it is designed.

#DO NOT undertake work on the bench without the workpiece being adequately secured. Use

clamps or a vice (not included) to secure the workpiece. Available from your Sealey dealer.

#DO NOT use the bench outdoors.

#DO NOT get the bench wet or use in damp or wet locations or areas where there is

condensation.

#DO NOT clean the bench with any solvents which may damage the surface or the protective

coating on the worktop.

2.1 Carefully unpack the product and check the contents against the diagrams below. Should any items be missing or damaged make

immediate contact with your Sealey dealer.

Please Note: These numbers relate to the parts

as packed in the box.

A. Bottom plate (1200 x 600 x 9mm)

B. Table top (1200 x 600 x 18mm)

C. Holed plate (1200 x 606 x 6mm)

D. Top plate (1196 x 220 x 6mm)

1. Bolt M6 x 15mm (x6)

2. Bolt M6 x 10mm (x54)

3. Nut M6 (x60)

4. Washer M6 (x120)

5. Wood screw (x4)

6. Tool hooks for holed plate (x30)

10. Top rail 1198mm (x1)

11. Cross member 1200mm (x5)

12. Left holed plate support (x1)

13. Right holed plate support (x1)

14. Left top cantilever arm 220mm (x1)

15. Right top cantilever arm 220mm (x1)

16. Side rail 600mm (x4)

17. Left rear leg 1000mm (x1)

18. Right rear leg 1000mm (x1)

19. Left front leg 900mm (x1)

20. Right front leg 900mm (x1)

21. Left guide rail 602mm (x1)

22. Right guide rail 602mm (x1)

23. Drawer 450mm x 1115mm (x1)

AP12600 - 2 - 161006

3. ASSEMBLY

STEP 1. Place the left and right plate supports (12 and 13) on a level surface

and then mount a cross member (11) across the top of these keeping the

ledge to the top, using only one M6 10mm bolt per side in the top holes.

STEP 2. Mount the holed plate (C) inside this frame and secure at the

top using one M6 15mm bolt per side.

STEP 3. Position and fix the left and right cantilever arms (14 and 15) to the

corners at the top of the frame.

STEP 4. Mount the top rail (10) between the two cantilever arms with the

smaller ledge towards the top.

AP12600 - 2 - 161006

Please note: Unless otherwise stated in the following instructions, use M6 x 10mm bolts (Part No.2), two M6 washers (4) per bolt and one

M6 nut (3) per bolt.

STEP 5. Mount the top plate (D) onto this framework, securing using the four

wood screws (5) through the cantilever arms.

STEP 6. Place the left and right rear legs (17 and 18) on a level surface

and attach two cross members (11) between them.

5 6

7 8

STEP 7. Attach the four side rails (16) to the rear legs. STEP 8. Mount the left and right guide rails (21 and 22) onto the rear

legs.

STEP 9. Mount and fix the left and right front legs (19 and 20) onto the

side rails.

STEP 11. Attach and fix the last cross member (11) between the front legs. STEP 12. Place the workbench upright onto its legs. Slide the pre-

assembled drawer into place along the guide rails.

STEP 10. Mount a cross member (11) between the top of the front legs

keeping the small ledge towards the top of the bench.

STEP 13. Place the bottom plate (A) onto the lower part of the workbench

and table top (B) onto the top of the workbench.

STEP 14. Position the assembled tool plate from STEP 6, inside the rear

brackets and attach onto the workbench by using four M6 x 15mm bolts

through the holed plate at the back and four M6 x 10mm bolts through the

side holes.

AP12600 - 2 - 161006

01284 757500

01284 703534 sales@sealey.co.uk

Sole UK Distributor

Sealey Group,

Bury St. Edmunds, Suffolk.

www.sealey.co.uk

Web

11 12

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.

Andere Sealey Werkzeugaufbewahrung Handbücher

Sealey

Sealey AP1640 Bedienungsanleitung

Sealey

Sealey PTB104008 Bedienungsanleitung

Sealey

Sealey AP2020BB Bedienungsanleitung

Sealey

Sealey AP1200MW Bedienungsanleitung

Sealey

Sealey AP6310 Bedienungsanleitung

Sealey

Sealey AP6310BE Bedienungsanleitung

Sealey

Sealey AP5520SS Bedienungsanleitung

Sealey

Sealey AP12160 Bedienungsanleitung

Sealey

Sealey PTB660TR Bedienungsanleitung

Sealey

Sealey AP26059TBRG Bedienungsanleitung

Sealey

Sealey APMS20 Bedienungsanleitung

Sealey

Sealey API1500 Bedienungsanleitung

Sealey

Sealey AP1520 Bedienungsanleitung

Sealey

Sealey AP28104 Bedienungsanleitung

Sealey

Sealey AP1205 Bedienungsanleitung

Sealey

Sealey AP2416.V2 Bedienungsanleitung

Sealey

Sealey AP28102BR Bedienungsanleitung

Sealey

Sealey AP2513B.V3 Bedienungsanleitung

Sealey

Sealey APMS60 Bedienungsanleitung

Sealey

Sealey AP1100M Bedienungsanleitung

Sealey

Sealey AP1248SS Bedienungsanleitung

Sealey

Sealey AP4206BE Bedienungsanleitung

Sealey

Sealey APLHT Bedienungsanleitung

Sealey

Sealey AP4804SS Bedienungsanleitung

Beliebte Werkzeugaufbewahrung Handbücher anderer Marken

Ryobi

Ryobi RWB03 Bedienungsanleitung

Husky

Husky H27CH5TR4BGK Bedienungsanleitung

Scheppach

Scheppach ts 2100 Bedienungsanleitung

Cornwell Tools

Cornwell Tools CTB360AKBK Bedienungsanleitung

DIVERSIFIED WOODCRAFTS

DIVERSIFIED WOODCRAFTS SHAIN GSB-6024 Bedienungsanleitung

Cassese

Cassese CS200 CART Bedienungsanleitung

Kendall Howard

Kendall Howard ESDW-9630-1000 Bedienungsanleitung

Lista

Lista Align Montageanleitung

Workzone

Workzone 99609 Bedienungsanleitung

Stanley

Stanley STST83800-1 Bedienungsanleitung

Homak

Homak PROFESSIONAL Series Systemhandbuch

Perel

Perel ROLLER SHUTTER STORAGE CABINET Bedienungsanleitung

Husky

Husky H5CH2R Bedienungsanleitung

BGS technic

BGS technic 4107 Bedienungsanleitung

Clarke

Clarke CWB1250 Bedienungsanleitung

Ryobi

Ryobi RWB02 Bedienungsanleitung

Husky

Husky H52CH6HDV3WHT Bedienungsanleitung

General International

General International Excalibur 40-100 Stücklistenhandbuch