Sealey AP2020BB Bedienungsanleitung

INSTRUCTIONS FOR:

HEAVY-DUTY WORKBENCH WITH 2 DRAWERS

BALL BEARING RUNNERS

MODEL No’s :AP2020BB

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

2. CONTENTS AND SPECIFICATION

1.1 GENERAL SAFETY

!WARNING! Ensure Health & Safety, local authority, and general workshop practice

regulations are adhered to when using this bench.

"Locate bench in a suitable working area.

"Keep the work area clean, uncluttered and ensure there is adequate lighting.

!WARNING! Use bench on level and solid ground, preferably concrete. Avoid tarmacadam

since the bench may sink into the surface.

"Keep the bench clean and tidy in accordance with good workshop practice.

"Keep children and unauthorised persons away from the working area.

#DO NOT use the bench for any purpose other than that for which it is designed.

#DO NOT exceed maximum capacity of workbench.

#DO NOT undertake work on the bench without the workpiece being adequately secured. Use

clamps or a vice (not included) to secure the workpiece. Available from your Sealey dealer.

#DO NOT use the bench out of doors.

#DO NOT get the bench wet or use in damp or wet locations or areas where there is

condensation.

#DO NOT clean the bench with any solvents which may damage the paint surface or the

protective coating on the wooden top.

!Maximum weight for each drawer is 25kg, full load for workbench is 250kg.

AP2020BB - 1 - 260407

2.1 Powder coated steel panels with 40mm wood laminate top. Two drawers, open storage space for larger items. Supplied flat packed.

2.2 Table Size (W x D): 1372 x 508mm

Working Height: 865mm

Capacity: 250kg

2.3 Carefully unpack the product and check the contents against the diagram below. Should any items be missing or damaged make

immediate contact with your Sealey dealer.

A . . . .SIDE PANEL G . . . .LEFT SIDE PANEL M . . . . .DRAWER R . . . . .RIGHT SlDE RUNNER

C . . . .BOTTOM RAIL H . . . .RIGHT SIDE PANEL O . . . . .CORNER BRACE S . . . . .SCREW (M5x12)

D . . . .TOP RAIL J . . . . .BACK PANEL P . . . . .WOODEN TOP T . . . . .ADJUSTABLE LEG LEVELLER

E . . . .CENTRE SUPPORT K . . . .SHELF Q. . . . .LEFT SIDE RUNNER U . . . . .HEX HEAD SCREW 5/8"

3. ASSEMBLY

STEP 2. Attach the outer slide to the corresponding left/right slide panel (G, H). Insert the tabs into the holes in the slide panel making sure that

the slider stop fits into the small hole.

AP2020BB - 1 - 260407

Ball bearing runner disassembly: Press the plastic lock spring up or down, and pull the inner

slide out. To put the runners back on, slot the inner slide into the middle slide and push all the

way in.

Step 1. As shown in the diagram attach the two large side panels (A), bottom rail (C) and centre support (E) together.

AP2020BB - 1 - 260407

STEP 5. Turn the workbench upside down and screw in the base

shelves (K). Also screw in the corner braces (O) as shown

in the diagram. At each corner attach the leg levellers (T).

STEP 4. Secure the back panel using 8 screws, 4 in each corner.

Step 3. Attach the side panels (G ,H) onto the main unit by screwing them to the front centre support (E) and side panels. Also screw

the top rails (D) onto the front and back.

STEP 6. Slide the workbench top (P) under the main unit and fix

with 4 hex head screws (U).

STEP 7. Attach the inner slide onto the drawer. Slot the

horizontal tab into the hole in the drawer and the vertical

tab into the other hole. Push down until the stop slots

into the small hole.

STEP 8. Pull the middle slide and the ball bearings out as far as possible. Hold the drawer and slot the inner slide on the drawer into the middle slide,

then push the drawer all the way in.

To remove drawer see Step 2.

66 7

AP2020BB - 1 - 260407

Inhaltsverzeichnis

Andere Sealey Werkzeugaufbewahrung Handbücher

Sealey

Sealey AP260613T Bedienungsanleitung

Sealey

Sealey AP4804SS Bedienungsanleitung

Sealey

Sealey AP1205 Bedienungsanleitung

Sealey

Sealey AP2405 Bedienungsanleitung

Sealey

Sealey PTB91508 Bedienungsanleitung

Sealey

Sealey PTB181510 Bedienungsanleitung

Sealey

Sealey AP22DFC Bedienungsanleitung

Sealey

Sealey APMS20 Bedienungsanleitung

Sealey

Sealey PTB66004SS Bedienungsanleitung

Sealey

Sealey AP1520 Bedienungsanleitung

Sealey

Sealey AP28102BR Bedienungsanleitung

Sealey

Sealey AP12600 Bedienungsanleitung

Sealey

Sealey AP223 Bedienungsanleitung

Sealey

Sealey P0618.V2 Bedienungsanleitung

Sealey

Sealey AP0618.V3 Bedienungsanleitung

Sealey

Sealey AP0615 Bedienungsanleitung

Sealey

Sealey PTB104008SS Bedienungsanleitung

Sealey

Sealey APLHT Bedienungsanleitung

Sealey

Sealey AP4206BE.V2 Bedienungsanleitung

Sealey

Sealey PCT1 Bedienungsanleitung

Sealey

Sealey AP2020 Bedienungsanleitung

Sealey

Sealey AP5520SS Bedienungsanleitung

Sealey

Sealey PTB66004 Bedienungsanleitung

Sealey

Sealey AP26479TBRG Bedienungsanleitung

Beliebte Werkzeugaufbewahrung Handbücher anderer Marken

Ryobi

Ryobi RWB03 Bedienungsanleitung

Husky

Husky H27CH5TR4BGK Bedienungsanleitung

Scheppach

Scheppach ts 2100 Bedienungsanleitung

DIVERSIFIED WOODCRAFTS

DIVERSIFIED WOODCRAFTS SHAIN GSB-6024 Bedienungsanleitung

Cassese

Cassese CS200 CART Bedienungsanleitung

Cornwell Tools

Cornwell Tools CTB360AKBK Bedienungsanleitung

Kendall Howard

Kendall Howard ESDW-9630-1000 Bedienungsanleitung

Lista

Lista Align Montageanleitung

Workzone

Workzone 99609 Bedienungsanleitung

Stanley

Stanley STST83800-1 Bedienungsanleitung

Homak

Homak PROFESSIONAL Series Systemhandbuch

Perel

Perel ROLLER SHUTTER STORAGE CABINET Bedienungsanleitung

Husky

Husky H5CH2R Bedienungsanleitung

BGS technic

BGS technic 4107 Bedienungsanleitung

Clarke

Clarke CWB1250 Bedienungsanleitung

Ryobi

Ryobi RWB02 Bedienungsanleitung

Husky

Husky H52CH6HDV3WHT Bedienungsanleitung

General International

General International Excalibur 40-100 Stücklistenhandbuch