SECO-LARM Enforcer E-941SA-80Q Bedienungsanleitung

ELECTROMAGNETIC LOCK Installation ManualELECTROMAGNETIC LOCK Installation Manual

SECO-LARM U.S.A., Inc.

When power is applied to the electromagnetic lock, it turns on the unit's

powerful built-in electromagnet. This electromagnet is attracted to the steel

armature plate which is mounted on a door, holding the door fast against

unauthorized entry. When power to the magnetic lock is turned off, the

electromagnet releases the armature plate, allowing the door to open.

SPECIFICATIONS

80-LB. MINIATURE

ELECTROMAGNETIC LOCKS

12~24VDC

23/4x 11/4x 13/16 in. (70 x 31 x 20 mm)

23/8x 11/4x 23/64 in. (60 x 31 x 9 mm)

80 lb. (36kg.) @ 12VDC

110lb.(51Kg.) @ 24VDC

85mA@12VDC

165mA@24VDC

± 10%

Aluminum

14°F to 131°F (-10°C to 55°C)

0.90 lb. (410 grams)

HOW THEY WORK

Installation Manual

E-941SA-80Q

Also available:

E-941SA-1200

1200-lb. electromagnetic lock

E-941SA-600

600-lb. electromagnetic lock

E-941SA-300

300-lb. electromagnetic lock

E-941SA-1K2PD

1200-lb. electromagnetic lock with status LED status sensor & delay timer

E-941DA-1K2P

Double-Door 1200-lb. electromagnetic lock with status LEDs & status sensors

E-942SA-1300

1300-lb. water-resistant gate lock

E-942SA-600

600-lb. water-resistant gate lock

Page 4

Power

MagnetSize

ArmatureSize

HoldingForce

CurrentDrain

VoltageTolerance

Housing

Temperature

Weight

PITLW1

Filename:MIE941SA-80_056.PMD

REGULAR MAINTENANCE

• Clean the contact surfaces of the electromagnet or armature plate with a soft cloth and non-

abrasive, non-corrosive cleaner.

• Apply a light coat of a silicon lubricant and wipe away the excess to prevent rust.

• Check that the armature plate is securely attached to the door, yet can pivot slightly around the

armature screw.

• Check that the electromagnet is securely attached to the door frame.

TROUBLESHOOTING

Problem:

Door does not lock

Door locks, but can be easily

forced open

Delay in door releasing

Possible cause:

No power

Poor contact between

electromagnet and

armature plate

Insufficient voltage

A secondary diode was

installed across the

electromagnet

Solutions:

• Check to make sure the wires are connected

properly.

• Check that the power supply is connected and

operating

• Make sure the lock switch is wired correctly

• Make sure the electromagnet and armature plate

are properly aligned

• Make sure the contact surfaces of the

electromagnet and armature plate are clean and

free from rust

• Check the power leads with a meter, and make

sure power is supplied between 12~24VDC.

• The electromagnet is fitted with a metal oxide

varistor to prevent interference, so do not install a

secondary diode

NOTICE

The information and specifications printed in this manual are current at the time of publication.

However, the SECO-LARM policy is one of continual development and improvement. For this

reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is

also not responsible for misprints or typographical errors.

reproduced or copied, in whole or in part, without the written permission of SECO-LARM.

SECO-LARM®U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326

Website:www.seco-larm.com

E-mail:sales

seco-larm.com

WARRANTY: ENFORCER Electromagnetic Locks are warranted against defects in

material and workmanship while used in normal service for a period of one (1) year from the

date of sale to the original customer. Our obligation is limited to the repair or replacement of

any defective part if the unit is returned, transportation pre-paid, to SECO-LARM.

SECO-LARM U.S.A., Inc.

E-941SA-80 Installation Manual

E-941SA-80

Installation Manual

Page 2 Page 3

A. Drill holes for the mounting plate and

armature plate (see fig. 1 and 2) by

doing the following:

1. Fold the mounting template along

the dotted line

2. Close the door. Find a mounting

location on the door frame near the

upper free-moving corner of the

door, as close to the corner of the

door frame as possible.

3. Place the template against the door

and frame.

4. Drill two holes in the door frame for

the mounting plate and three holes

in the door as indicated on

template.

5. Only from the sexnut bolt side of the

door, enlarge the 5mm hole to

9mm.

B. Mount the armature plate to the door

using the two steel and one rubber

washer (fig. 2):

NOTE — Actual installation varies

according to door style.

1. Secure the two guidepins into the

two side holes of the armature

plate.

2. Insert the armature screw into the

armature plate, then put the rubber

washer between two steel washers,

and place them over the armature

screw between the armature plate

and the door. This will allow the

armature plate to pivot slightly

around the armature screw in order

to compensate for door

misalignment.

2. Insert the sexnut bolt into the 9mm

hole, then tighten the sexnut bolt and

the armature screw, just enough so the

armature plate can withstand the force

of someone attempting to break down

MOUNTING THE E-941SA-80Q

the door while the electromagnet is

engaged.

3. Do not tighten the armature plate

against the door. The plate must be

able to pivot around the armature

screw.

C. Screw the mounting plate to the door

frame:

1. Remove the L-shaped mounting

plate from the magnet.

2. Insert the provided two 1

/8" x 1"

(4 x 25.4 mm) screws into the

L-shaped mounting plate and

screw it to the door frame. The

armature plate and the mounting

plate must be concentric or align

with each other.

D. Drill the power cable access hole.

E. Mount the electromagnet to the door

frame (fig. 1) — Use the Allen wrench

to screw the socket-head mounting

screws through the bottom of the

electromagnet into the mounting

bracket.

F. Connect the power leads (fig. 3):

1. Run two power leads from the

power supply through the power

cable access hole into the

electromagnet.

2. Connect the power leads to the red

and black power input wires of the

unit. Observe correct polarity, red

for positive and black for negative.

G. Test the unit.

123456789

12345

Sexnut

bolt

This side drill

9mm only

Drill a 5mm

hole thru door

Armature

Screw

Steel and

Rubber

washers

(as

needed)

Armature

HOLLOW METAL DOOR

Drill an 5mm hole thru door. From sexnut

bolt side only, enlarge the 5mm hole to

9mm.

Drill an 5mm hole thru door. From sexnut

bolt side of door, drill 9mm (

23/64

") hole,

25mm in depth.

Drill a 3.5mm dia. hole and tap for

M5 x 0.8 thread.

Sexnut

bolt

Drill 9mm

(23/64") Drill a 5mm

hole thru door

Armature

Screw

Armature

SOLID CORE DOOR

Armature Screw

Tap M5 x 0.8 Thread

REINFORCED DOOR

Armature

FIG.1 Standard Mounting

FIG. 2 Types of armature plate mounting

FIG. 3 Wiring diagram

123456

Steel and

Rubber washers

(as needed)

Steel and

Rubber washers

(as needed)

Power wires to

electromagnet Control

Device

Red

Black

12~24VDC

Power

Supply

L-shaped

Maounting

bracket

Magnet

Sexnut

bolt

Armature Plate

Steel and Rubber washers

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SECO-LARM Sperren Handbücher

SECO-LARM

SECO-LARM SD-997C-GCQ Bedienungsanleitung

SECO-LARM

SECO-LARM E-941SA-80Q Bedienungsanleitung

SECO-LARM

SECO-LARM E-942FC-1300 Bedienungsanleitung

SECO-LARM

SECO-LARM Enforcer E-941SA-300 Bedienungsanleitung

SECO-LARM

SECO-LARM E-941DA-600Q Bedienungsanleitung

SECO-LARM

SECO-LARM SD-996C-NUVQ Bedienungsanleitung

SECO-LARM

SECO-LARM SLI ENFORCER 1200-lb Electromagnetic Lock... Bedienungsanleitung

SECO-LARM

SECO-LARM SLI E-942FC-1K3SQ Bedienungsanleitung

SECO-LARM

SECO-LARM CL-210M-U3BQ Bedienungsanleitung

SECO-LARM

SECO-LARM E-941SA-1K2PD Bedienungsanleitung

SECO-LARM

SECO-LARM SD-995C-D3Q Bedienungsanleitung

SECO-LARM

SECO-LARM E-941S 600DPSQ Series Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER SD-961A-36 Bedienungsanleitung

SECO-LARM

SECO-LARM E-941DA-600Q Bedienungsanleitung

SECO-LARM

SECO-LARM SD-993B-SS Bedienungsanleitung

SECO-LARM

SECO-LARM SD-997A-GBQ Bedienungsanleitung

SECO-LARM

SECO-LARM E-941SA-600 Bedienungsanleitung

SECO-LARM

SECO-LARM Enforcer E-941DA-1K2P Bedienungsanleitung

SECO-LARM

SECO-LARM E-941S 600 Series Bedienungsanleitung

SECO-LARM

SECO-LARM E-941SA-1K2PD Bedienungsanleitung

SECO-LARM

SECO-LARM SD-231-ND1Q Bedienungsanleitung

SECO-LARM

SECO-LARM SD-997B-1SQ Bedienungsanleitung

SECO-LARM

SECO-LARM SD-995A-D3Q Bedienungsanleitung

SECO-LARM

SECO-LARM E-946FC-600Q Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung