Seco SANTOKA 10.1 BX PCT IPS Bedienungsanleitung

Product Manual

SANTOKA 10.1 BX PCT IPS

Arm®Cortex®-A9 Panel Mount

PRODUCT MANUAL

SANTOKA

Document Revision History

The information in this document is subject to change without prior notice in order to improve reliability, design and

function and does not represent a commitment on the part of the manufacturer.

Online support on edge.seco.com

Revision Date Author Description

V 1 21.09.2017 CG Initial Release

V 2 15.03.2018 CG Page 18 New Picture RS485 Pin 6 to 11

V 3 12.09.2019 CG Change address

V 4 17.12.2021 bmy SECO CI Update 2022

PRODUCT MANUAL

SANTOKA

Table of Contents

1. Introduction .........................................................................................4

2. Safety Hints .........................................................................................5

3. Product Introduction ..........................................................................7

3.1 Type Plate and Device Information ..............................................................7

3.2 Product names and variants.........................................................................8

3.3 Related Documents and Online Support....................................................9

4. Technical Data .....................................................................................10

4.1 Block Diagram SBC .......................................................................................12

4.2 Connectors......................................................................................................13

5. Installation and Start Up.....................................................................15

5.1 Connection Scheme ......................................................................................15

6. Internal and External Interfaces.........................................................16

6.1 Wi-Fi and Bluetooth Antenna Connectors ..................................................16

6.2 Ethernet (X117) (1+2)....................................................................................16

6.3 Power (X1).......................................................................................................17

6.4 CAN/RS-485 Interface (X39)........................................................................18

6.5 USB Host (X34) ..............................................................................................19

6.6 USB Host (X113)............................................................................................19

6.7 Speaker (X9)...................................................................................................19

6.8 HDMI (X111) ...................................................................................................20

6.9 RS-232/RS-232 (X13)....................................................................................21

6.10 USB OTG (X20) ..............................................................................................22

6.11 SD Card Slot (X31) ........................................................................................22

6.12 Power LED (D30)............................................................................................23

6.13 Bootselect Switch (SW2) ..............................................................................23

6.14 Reset Switch (SW1) .......................................................................................23

6.15 Battery-Holder (X125) ...................................................................................24

6.16 BatterySpecications....................................................................................25

6.17 Replacement of the Internal Battery ...........................................................26

Annex A: Technical Drawing...............................................................................27

Annex B: Quality and Incoming Inspections .....................................................28

B-1 Display and Touch..........................................................................................28

Annex C: Evaluation criteria of standard display module ................................29

Annex D: Hardware Revision Information .........................................................30

Annex E: Assembly Options ...............................................................................31

E-1 Wi-Fi / Bluetooth .............................................................................................31

Annex F: Guidelines and Standards .................................................................32

F-1 RoHS Declaration...........................................................................................32

F-2 Supplier Declaration – Directive EG 1907/2006 REACH..........................32

F-3 ULCertication...............................................................................................32

F-4 SECO Northern Europe Conformity Statement.........................................33

Annex G: Common Documentation....................................................................34

G-1 Warranty hints.................................................................................................34

G-2 Field of Application.........................................................................................35

Annex H: Technical Support ..............................................................................36

Annex I: General Information............................................................................37

* alternative assembly upon request

PRODUCT MANUAL

SANTOKA

1. Introduction

Thank you very much for purchasing a SECO Northern Europe product. Our products are dedicated to professional

use and therefore we suppose extended technical knowledge and practice in working with such products.

The information in this manual is subject to technical changes, particularly as a result of continuous

product upgrades. Thus this manual only reflects the technical status of the products at the time

of printing. Before design-in the device into your or your customer’s product, please verify that this

document and the therein described specication is the latest revision and matches to the PCB

version. We highly recommend contacting our technical sales team prior to any activity of that kind.

The attached documentation does not entail any guarantee on the part of SECO Northern Europe

GmbH with respect to technical processes described in the manual or any product characteristics

set out in the manual. We do not accept any liability for any printing errors or other inaccuracies in

the manual unless it can be proven that we are aware of such errors or inaccuracies or that we are

unaware of these as a result of gross negligence and

SECO Northern Europe has failed to eliminate these errors or inaccuracies for this reason.

SECO Northern Europe GmbH expressly informs that this manual only contains a general

description of technical processes and instructions which may not be applicable in every individual

case. In cases of doubt, please contact our technical sales team.

In no event, SECO Northern Europe is liable for any direct, indirect, special, incidental or

consequential damages arising out of use or resulting from non-compliancy of therein conditions

and precautions, even if advised of the possibility of such damages.

Before using a device covered by this document, please carefully read

Annex „G-1 Warranty hints“

Annex „G-2 Field of Application“

Embedded systems are complex and sensitive electronic products. Please act carefully and ensure

that only qualied personnel will handle and use the device at the stage of development. In the

event of damage to the device caused by failure to observe the hints in this manual and on the

device (especially the safety instructions), SECO Northern Europe shall not be required to honour

the warranty even during the warranty period and shall be exempted from the statutory accident

liability obligation. Attempting to repair or modify the product also voids all warranty claims.

PRODUCT MANUAL

SANTOKA

2. Safety Hints

Please read this section carefully and observe the instructions for your own safety and correct use of the device.

Observe the warnings and instructions on the device and in the manual. SECO Northern Europe embedded

systems have been built and tested by us and left the company in a perfectly safe condition.In order to maintain this

condition and ensure safe operation, the user must observe the instructions and warnings contained in this manual.

I. General Handling

Don’t drop or strike the unit: The PCB, display and/or other parts might be damaged.

Keep away from water and other liquids, the unit is not protected against.

Operate the unit under electrical and environmental conditions according to the technical

specication.

The electrical installations in the room must correspond to the requirements of the local (country-

specic) regulations.

Take care that there are no cables, particularly power cables, in areas where persons can trip over

them.

Do not place the device in direct sunlight, near heat sources or in a damp place.

All plugs on the connection cables must be screwed or locked to the housing.

Repairs may only be carried out by qualied specialist personnel authorized by

SECO Northern Europe GmbH or their local distributors.

Maintenance or repair on the open device may only be carried out by qualied personnel

authorized by SECO Northern Europe GmbH which is aware of with the associated dangers.

II. Electricity

The embedded systems may only be opened in accordance with the description in this user’s

manual for

- replacing of the (rechargeable, where applicable) lithium battery and/or

- conguration of interfaces, where applicable

These procedures have to be carried-out only by qualied specialist personnel.

When accessing internal components the device must be switched off and disconnected from the

power source.

When purchased core or basic versions without protecting back cover, don’t touch the PCB directly

with your ngers. Especially these products need to be handled very carefully.

Don’t operate or handle the unit without typical ESD protection measures, such as ground

earthing.

Operate the unit according to the technical specication only.

III. Damage or Permanent Malfunction

It must be assumed that a safe operation is no longer possible, in case

-the device has visible damage or

-the display is dark or shows strange pattern for longer period

-the device doesn’t react after a reset

In these cases the device must be shut down and secured against further use

PRODUCT MANUAL

SANTOKA

IV. Approvals

The SANTOKA may be equipped with a certied transmitting module.

The internal / external antenna(s) used for this module must provide a separation distance of at

least 2 cm from all persons and must not be co-located or operating in conjunction with any other

antenna or transmitter.

The outside of nal products containing the SANTOKA module must display in a user accessible

area a label referring to the enclosed transmitting module. This exterior label can use wording

such as the following12: “Contains Transmitter Module FCC ID:

(insert the modules FCC ID)

” or

“Contains FCC ID:

(insert the modules FCC ID)

”.

Approved antennas list: For the WLAN/Bluetooth module WPEA-152GN(BT) a dipole antenna with

2 dBi (peak) gain is approved

V. FCC

To comply with FCC and Industry Canada RF exposure limits for general population /

uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a

separation distance of at least 2 cm from all persons and operating in conjunction with any other

antenna or transmitter, except in accordance with FCC multi-transmitter product procedures

Position of Typelabel

SECO Northern Europe article number

Product name and conguration

Power ratings

Production date (week/year)

Placeholder for additional test marks and approvals

UL approval

Manufakturer name and address

Serial number

(Exemplary Illustration (cutout) backside)

PRODUCT MANUAL

SANTOKA

3. Product Introduction

This document is applicable for hardware revisions 1.0 or later of the SANTOKA series.

Please nd the hardware version grid in „Annex D: Hardware Revision Information“:

SANTOKA is an Embedded System to be used as human machine interface (HMI) in various applications. Please

refer to Annex „G-2 Field of Application“ for further information. The system is equipped with a large number of

industrial interfaces. A wide variety of options is available as well.

3.1 Type Plate and Device Information

For service and later identication of the device, the type plate contains important information.

PRODUCT MANUAL

SANTOKA

3.2 Product names and variants

Product name denition:

SANTOKA <CPU> <7.0> <BX> <PCT> <IPS> <additional description> <Vx.y.z>

Explanation:

SANTOKA Product family name (invariable)

<CPU> x1, x2, x2l, x4, x4P (number of cores inside the i.MX6 processor)

<7.0> Display size in inch

<BX>, <SG>, <OF> mechanical design of enclosure

<PCT>, <RES> projected capacitive touch; if blank: 4-wire resistive / resistive touch

<IPS> Display technology “in-plane switching”, (option)

<additional description> contains variants which are important to sales product description, i.e.

without or with WLAN/Bluetooth module (“W/B”)

untreated glass surface or including antiglare treatment (“AG”)

front frame made from die-cast zinc or aluminium (“Alu”)

different memory capacities for RAM and/or eMMC

customer-specic reduced assembly

etc.

<Vx.y.z> revision of PCB layout

<x> describes major changes in form t and functions

<y> describes variants that are different in PCB layout and could affect the list of

critical components (UL LoCC).

<z> describes minor changes to PCB layout due to production optimization like

solder resist mask or drilling diameters.

Also minor changes in assembly of PCB and/or device which do NOT affect the

list of critical components (UL LoCC) due to unlisted components or declared

“interchangeable”.

Flash-N-Go

https://bit.ly/3xPzoHy

Contains information about the usage of the G&F Flash-N-Go solution

which consists of three submodules:

Flash-N-Go Boot (A tiny boot loader)

Flash-N-Go System (A maintenance os)

Flash-N-Go Update (A GUI based update solution for all os)

Linux Yocto Jethro

https://bit.ly/3lwp6an

Contains information about Linux BSP with development environment

Linux Embedded System Yocto (Codename: Jethro, Version 3.0) includes

rst information about the bootloader Flash-N-Go

Linux Yocto Rocko

https://bit.ly/3puByZA

Android 7.1

https://bit.ly/32XoCni

PRODUCT MANUAL

SANTOKA

3.3 Related Documents and Online Support

This document contains operating system specic information. The following additional documentations are

available:

OPERATING SYSTEMS

UPDATE / BOOT / SYSTEM

CPU x1 x2 x4 x4P

CPU Type i.MX6Solo i.MX6Dual i.MX6Quad i.MX6QuadPlus

Core Class Arm®Cortex®-A9

Core Clock 1 GHz

Features

NEON for SIMD media acceleration and VFP operations; Multi-format HD 1080p video decoder and HD

720p video encoder hardware engine; L1 cache, 32 KB for instruction, 32 KB for data

512 KB L2 cache 1 MB L2 cache

HW Accelerators OpenGL ES 2.0, OpenVG 1.1

RTC Accuracy: +/- 30 ppm at 25°C

Memory

eMMC Flash 4 GB MLC eMMC 8 GB MLC eMMC

RAM Standard 1 GB 32 bit DDR3L 1 GB 64 bit DDR3L 4 GB 64 bit DDR3L

SD Card Slot 4 bit MMC/SDIO/SD/SDHC

Operating Systems

Supported OS Linux Yocto Jethro

Communication Interfaces

Network 2x 10/100 Mbit/s Ethernet (RJ-45)

USB 2.0 2x 480 Mbit/s Host (Type A)

1x 480 Mbit/s OTG (Type Micro-AB) 1

CAN Fieldbus / RS-485 1x CAN (ISO/DIS 11898) +

1x RS-485 1x CAN (ISO/DIS 11898) + 1x RS-485 galvanic isolated

RS-232 2x RS-232 (RX/TX/CTS/RTS)

MDB 2/1x MDB (Master / Slave optional) 3instead of 2nd external RS-232

Synchronous

Serial Interfaces SPI up to 12 chip selects; I²C; Matrix keypad up to 8 x 8

Wireless Communication

Wireless WLAN 802.11 b/g/n; Bluetooth 4.0 LE / available as optional mPCIe card

Video

Video output Full HD HDMI

Audio

Speaker output 1x speaker (connector), 1.5 W RMS (8Ω)

PRODUCT MANUAL

SANTOKA

4. Technical Data

1Mechanically the Micro-USB interface has not been designed for frequent contact operations. Please use an

adapter cable with a strain relief.

2Option

3The selection of a variant eliminates the other.

Audio Internal 1x speaker 0.3 W RMS (8Ω)

Display and Touch

Size 10.1 inch / 256.54 mm

Resolution 1280 x 800 pixel

Brightness Typ. 420 cd/m2

Backlight Lifetime Typ. 50.000 h

Viewing Angle 85°, 85°, 85°, 85°(UDRL)

Color 24 bit (16.7 Mio. colors)

Touch projected capacitive multitouch

Inhaltsverzeichnis

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-521 Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung