Secu SELO-C Bedienungsanleitung

Subject to modifications -- page 1 --

SELO-C-Standard-Betriebsanleitung-englisch.p65 Date: 12.06

Operating instructions - Basic functions

of electronic lock SELO-C (Version 1.0)

Fully redundant electronic lock model SELO-C allows you to open the lock after entering the valid 7- or 8-digit secret code. The

maximum number of codes for clearing the lock is 10.

A) GENERAL

- The opening procedure consists of two operations: CLEARING and UNBLOCKING.

- To start the opening procedure, check that the input unit is in the vertical end position.

- All accepted key strokes will produce a response on the display.

- Ifthecodenumberiskeyedinbymistake,returntothestartingpositionofthelockbypressingtheOn/Enterkey,andstart

over.

- Afterenteringthewrongsecretcodethreetimesinarow,thelockwillautomaticallyblockallfurtherentriesfor5minutes.

If, after waiting for 5 minutes, the wrong code is entered again, the lock will block itself for a further 20 minutes

(manipulationresistance). Duringthis time,the remainingdelay isdepicted onthe displayand noteven thevalid number

code will open the lock.

- If more than 30 seconds lapse between pressing any two keys, the lock automatically switches itself off for safety reasons.

The opening procedure has to be started over.

- Once data have been stored (numerical codes, time frame and user entries), not even a power failure will delete them.

- Thelockisoffullyredundantdesign.Thismeansthatallelectricalcomponentswhicharecrucialtotheproperfunctioning

of the lock come in pairs. In the unlikely event of the primary system breaking down, the lock can, therefore, always be

opened undamaged using the secondary or backup system.

3 lines for entering codes and

displaying messages

1 line for displaying battery

condition and key functions

Function key for correcting data

input and selecting menu

functions

On/Enter-key to switch on the

unit, select functions and to set

the lock to its starting position

Rotary handle for unblocking

the lock

Multifunction keys „2“ , „4“, „5“,

„6" and „8“ for moving the cursor

and entering the code

Keys „0“ - „9“ for entering

numbers and plain text

- Battery condition „1/3 full"

- Key marked „Function“ to return

to next higher menu level

- Keys „1“ and „2“ to navigate

through the menu

- Battery condition „full“

- Key marked „Function“ to select

the desired menu from the

setting mode

- Battery condition „2/3 full"

- Key marked „Function“ for

deleting the figure entered last

- Battery condition „almost empty"

Multifunction keys „1“ and „2“

for entering figures and words,

and for menu navigation

C) CHANGING THE NUMERICAL CODE

TEST – TO BE PERFORMED WITHOUT FAIL!!

Forsafetyreasons,onlyreprogramthelockwiththesafedooropenandblockedintheopenposition.Onlyafteryouareabsolutely

certainthatthelockhasbeenreprogrammedsuccessfullyandthatthelockcanbeelectricallyclearedandmechanicallyunblocked

using the new settings, should the door be closed.

B) OPERATION

Code entering procedure

The procedure by which individual code entries are made is cursor-controlled. Before entering a figure, one of the 10 numbers on the

display will show up as a blinking black rectangle. The lock selects the space for the first figure at random. To move the cursor, use

direction keys “2” (up), “4” (left), “6” (right), “8” (down). When, at the end of the movement, the cursor blinks in the position of

the figure to be entered, complete entering of the figure by pressing “5”.

The following example shows one possibility of entering the figure 2 when the random starting position of the blinking black cursor

rectangle happens to be on the figure 6:

1. Presscursordirectionkey“4” oncetomovethecursor

to the left from the 6 to the 5.

2. Presscursordirectionkey“2” oncetomovethecursor

up from the 5 to the 2.

3. Press code entering key “5” once to complete select-

ing the figure 2 as one of the figures of the secret code.

Clearing the lock

1. Press On/Enter. When the lock is ready for operation, you will be asked to enter the code eight seconds after the status of the

opening counter is displayed. You can abort the opening counter indication by pressing any number key.

2. Now enter the 7- or 8-digit numerical code (factory setting: administrator code 1 2 3 4 5 6 7). Each successfully entered figure

willbeconfirmedby a starappearing underneaththe wordCODE:.After enteringthelast digit,the code isvalidated bythelock.

3. If the lock is able to match the entry with a previously programmed code, it will prompt the operator for five seconds to turn the

round input unit and to start unblocking the lock.

Unblocking the lock - relocking and securing the lock

1. To unblock the lock during the five second readiness for opening, turn the round input unit clockwise through a half turn from

itsendposition.Pleasenotethattheinputunitcanbeturnedaquarterturnatanytime,butthatthisdistanceisnotenoughtounblock

the lock.

2. If the input unit is turned back to its starting position in anti-clockwise direction after the five-second ready-for-opening period,

the lock will return to the blocked position and can only be unblocked after renewed clearing and re-entry of a valid code.

-- page 2 --

-- page 3 --

SELO-C-Standard-Betriebsanleitung-englisch.p65

Enter the setting mode to change one of the codes

ONLYCHANGETHELOCKSETTINGSWITHTHESAFEDOOROPENANDBLOCKED. DONOTMAKEUP

NUMBER CODE OF PERSONAL DATES (i.e. no wedding anniversaries, birthdays etc.)

1. PressOn/Enterkey.Whenthelockisreadyforoperation,thewelcomingphraseonthedisplayisfollowedaftereight

seconds by a message prompting the operator to enter a valid code. The black rectangular cursor symbol will blink

inthepositionofthefirstrandomfigureofthecodeentryrangeandthecapitalletter“M”appearsabovetheFunction

key.

2. By pressingtheFunction key, themenusof the settingmodeappear.In this mode,thesymbols above keys“1”and

“2”serveasoperatingsymbolstonavigatethroughthemenu(upordown).ThefirstmenutoappearisCodechange.

Use keys “1” and “2” to activate the other options on the menu.

Changing the administrator code (factory setting 1 2 3 4 5 6 7)

1. Assoonasyouenterthesettingmode,thecursorwillautomaticallygotoCodechange.Toselect,presstheOn/Enter

key.

2. Next,theadministratorandthevarioususersaredepictedonthedisplaywiththeadministratorinfirstplace.Toselect

the administrator, press On/Enter.

3. Thelockwillnowask youto entertheoldcodeusedthusfar bydisplaying thewordCODE.O:. Key-intheoldcode

(when taking the lock into operation the first time, enter the factory setting 1 2 3 4 5 6 7) and confirm with the On/

Enterkey.

4. Next, the lock prompts the operator to enter the new code by displaying the word CODE.N:. Key-in the new code

andconfirmbypressingOn/Enter.Asasafetyfeature, thelockpromptstheoperatortoenterthenewcodeasecond

time by displaying the word CODE.R:. Confirm once more by pressing the On/Enter key.

5. The lock confirms the successful change of the administrator code by means of the message Code change

completed!;iftheoperationwasnotsuccessful,themessagewillreadCodechangeerror!.Youcanleavetheactive

menufieldinthesetting modebypressingtheFunctionkeywhenever yousee thesymbol“<“abovethekey.After

leaving the setting mode, the lock is again ready for clearing. The operator is prompted to enter a valid secret code.

Changing an existing user code

1. Assoonasyouenterthesettingmode,thecursorwillautomaticallygotoCodechange.Toselect,presstheOn/Enter

key.

2. Next, the administrator and the various users are depicted on the display with the administrator in first place. In the

setting mode, the symbols above keys “1” and “2” serve as operating symbols to navigate through the menue (up

or down). Using keys “1” und “2”, go to the user whose code is to be changed. Select the desired user by pessing

On/Enter.

3. Thelocknowpromptstheoperatortokey-intheuser’soldcodefarbydisplayingthewordCODE.O:.Enteroldcode

and confirm by pressing On/Enter.

4. Next, the lock prompts the operator to key-in the user’s new code far by displaying the word CODE.N:. Enter new

code and confirm by pressing On/ Enter. As a safety measure, the lock prompts the operator to enter the new code

a second time far by displaying the word CODE.R:. Enter code and confirm once more by pressing the On/Enter

key.

5. The lock confirms the successful change of the user code by means of the message Codechangecompleted!; if the

operation was not successful, the message will read Code change error!. You can leave the active menue field in

the setting mode by pressing the Function key whenever you see the symbol “<“ above the key. After leaving the

setting mode, the lock is again ready for clearing. The operator is prompted to enter a valid secret code.

D) CHANGING THE LANGUAGE

Entering the setting mode to change the language setting

1. PressOn/Enterkey.Whenthelockisreadyforoperation,thewelcomingphraseonthedisplayisfollowedaftereight

seconds by a message prompting the operator to enter a valid code. The black rectangular cursor symbol will blink

inthepositionofthefirstrandomfigureofthecodeentryrangeandthecapitalletter“M”appearsabovetheFunction

key.

2. By pressing the Function key, the menue of the setting mode appears. In this mode, keys “1” and “2” serve as

operatingsymbolsformenuenavigation(upordown).ThefirstmenuetoappearisCodechange.Usethesamekeys

“1” and “2” to address the other options on the menue.

-- page 4 --

E) REPLACING THE BATTERIES

As soon as the symbol depicting the battery condi-

tion indicates „almost empty“, the operator is also

warnedPleasereplacebatteries!eachtimethelock

is operated. We recommend you heed the advice

and change the batteries! The lock can only be

unblockedafurther,approximately,50times.Please

notethatnoneofthe number codes canbechanged

until a set of fresh batteries has been fitted. To

changethebatteries,liftoff thecoverof thebattery

compartmentwiththetipofascrewdriver.Fitthree

leak-proof,typeMignon LR6,AA,alkaline batter-

ies, paying attention to the correct polarity. Dispose of the old batteries in accordance with anti-pollution legislation!

G) ADDITIONAL LOCK SETTINGS

For detailed information about the additional lock functions, please check the CD-ROM supplied with the lock. These

functions cover:

- Timefunctions----------------- Set time

- Set date

- Administratorfunctions - Define number of digits of secret codes

- Reorganize

- Assignment and administration of user codes

- Read out list of operations

- Display lock information

F) BACKUP MODE

The advantage of the fully redundant design is that the lock can be switched over from standard to backup mode in case

of a failure of the standard lock system. To open the lock after switching to backup mode, enter the code previously

assignedinthebackupmode.However,untilthesystemadministratorhaschangedthefactory-setadministratorcodefor

the backup mode, i.e. 1 2 3 4 5 6 7, to the secret code of his choice, the lock will send out the warning Backup cde still

factory setting whenever it is switched on.

IMPORTANT SAFETY ISSUE !

When preparing the lock for operation for the first time, change the factory-set administrator code 1 2 3 4 5 6 7

of the backup system to the secret code of your choice. Failing this, the lock can be opened by anybody knowing

the factory setting whenever it is in backup mode.

Opening the lock backup mode

1. Press On/Enter. Next, press Function key to enter the menu of the setting mode. Above the “1” and “2” keys you

will see the symbols for navigating through the menu (up or down). The first item to appear is the menu for Code

change.

2. Using keys “1” and “2”, go to Mode select. To select, press On/Enter.

3. Using keys “1” and “2”, go to sub-item Reserve mode. To select, press On/Enter. Using the Function key, return

to the point where you are requested to enter a code. After keying in any code entered in the backup mode, the lock

is now ready for opening (the next time the lock is started up normally will automatically be in the standard mode).

Selecting a different language

1. Having entered the setting mode, use keys “1” and “2” to go to the field Language/Sprache in the menue (factory

setting when the lock is installed the first time is German (deutsch).Select by pressing the On/Enter key.

2. Use keys “1” and “2” to go to the language of your choice. Select the new language by pressing the On/Enter key.

Fromnowon,allmessageswillappearinthelanguageofyourchoice.Toleavethepresentmenuefieldinthesetting

mode, press the Functionkey whenever you see the symbol “<“above the key. After leaving the setting mode, the

lockisagainreadyforclearing.Theoperatoris promptedto entera validsecretcodeinthelanguageoftheirchoice.

Andere Secu Sperren Handbücher

Secu

Secu E4000R Bedienungsanleitung

Secu

Secu E2000 Bedienungsanleitung

Secu

Secu S2700U Bedienungsanleitung

Secu

Secu S6500 Bedienungsanleitung

Secu

Secu SELO-B Bedienungsanleitung

Secu

Secu E4500 Bedienungsanleitung

Secu

Secu SELO-B 2 Bedienungsanleitung

Secu

Secu Selo - B V.2 FP Bedienungsanleitung

Secu

Secu Selo-B V.2 Bedienungsanleitung

Secu

Secu SELO-BR Bedienungsanleitung

Secu

Secu E4000R Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung