Secure SCS317 Bedienungsanleitung
SCS317
User Instructions
SCS317 7 Day Wireless Programmable
Room Thermostat
Programmable room thermostats are widely recognised as one
of the best ways in which to control central heating. The SCS317
programmable room thermostat has a large display and intuitive
user interface, making it easy to set up and use. SCS317 uses a
sophisticated time proportional integral (TPI) algorithm for
accurate temperature control and energy efficiency.
1
Actual Room
Temperature
Day of
Week
Time of
Day
Until (Time)
Then (Temp)
Enter
Button
+ Button- ButtonBack
Button
Set
Temperature
DISPLAY
SCS317
2
DISPLAY
Actual Room Temperature This is the actual room temperature
measured by the SCS317
Set Temperature This is the temperature that the SCS317
will allow the room to reach. The
temperature range can be set between
5°C and 30°C
When the temperature shown in the
display is achieved the SCS317 will
switch the heating OFF.
If the temperature in the room falls below
the setting the SCS317 will switch the
heating ON.
Until (time) This is the time that the next
temperature setting is due to operate
Then (temp) This is the temperature setting that is
due to operate next
Day of the week It is important that the correct day of the
week shows in the display
Time of day This is the current time of day
Setting Buttons Press any button to illuminate the
display.
The message 'To override press -/+ To
see menu press ENTER' will appear
No Radio waves Wireless connection not set up
Solid Radio Antenna Z-Wave communication present
– Flashing Radio Antenna – Temporary
loss of Z-Wave communication
ACTIVATING THE BACK-LIT DISPLAY
Press any button to illuminate the display. This will remain illuminated for
10 seconds
GENERAL INFORMATION
During programming please note that the display will return to its normal
operating screen if the last button press exceeds 10 seconds. 3
TEMPORARY OVERRIDE
A temporary temperature change can be made at any time. It is
also possible to extend how long this temperature override is in
operation.
The temperature will revert to its normal programmed setting at
the next timed temperature change
TEMPORARY OVERRIDE WITH TIME EXTENSION
(Maximum of 4 hours)
The temperature will revert to its normal programmed setting
at the next timed temperature change.
Press ‘-’ or ‘+’ to
adjust temperature
New temperature
setting will be shown
on the display
Press ‘-’ or ‘+’ to
adjust temperature
New temperature
setting will be
shown on the
display
Press ENTER
Press ‘+’ to
adjust the time
Press ENTER The hours of
the UNTIL time
will flash
4
PERMANENT OVERRIDE
In the 'HOLD' position the temperature can be overridden by
pressing either the '-' or '+' buttons. This will then become the
new 'HOLD' temperature
PERMANENT OVERRIDE – CANCELLATION
Press ‘-’ or ‘+’ to
adjust temperature
New temperature
setting will be
shown on the
display
Press ENTER
The hours of
the UNTIL time
will flash
Press ENTER
Press the '+'
repeatedly until
HOLD appears in
the display
Message will
appear briefly
confirming
'Temperature set
until manual
release'
Press BACK Press ENTER
5
SETTING UP THE SCS317
Upon initial installation the SCS317 has the following factory
default settings
Settings – Monday to Friday
Time Target Temperature
Period 1 06:00 am 20 °C
Period 2 08:30 am 18 °C
Period 3 11:30 am 20 °C
Period 4 01:30 pm 18 °C
Period 5 05:00 pm 21 °C
Period 6 10:00 pm 15 °C
Settings – Saturday and Sunday
Time Target Temperature
Period 1 07:00 am 20 °C
Period 2 10:00 am 19 °C
Period 3 11:30 am 21 °C
Period 4 01:30 pm 18 °C
Period 5 05:00 pm 21 °C
Period 6 11:00 pm 15 °C
These can be changed by the installer or the end user at any
time by accessing the MAIN MENU
6
MAIN MENU
To access the MAIN MENU take the following steps:
MENU OPTIONS
Press ENTER twice Press '-' or '+' to
toggle between the
menu options
Programme This allows the user to adjust the different
time and temperature settings from the
factory default settings shown in the table on
page 6.
Up to six different temperature levels can be
set in any 24 hour period
Standby This puts the SCS317 into Frost protection or
Standby condition and allows the heating to
be permanently switched off but will activate
and switch the heating on if the temperature
in the house falls below the standby
temperature set.
All programme settings are overridden and
the unit will not return to normal operation
until the standby period has ended by
pressing the ENTER button.
Holiday This puts the SCS317 into a temporary
standby mode with a start and end date
which can be set to coincide with a holiday
period. At the end of the set period the
SCS317 will resume normal operation
Time / Date The SCS317 has a built in clock and
calendar. This will require setting on initial
installation. If this has not been set on
installation please go to Setting the TIME and
DATE section on page 12 before continuing
Set Up Enables the programming of various options
outlined in the SET UP MENU on page 13 of
these instructions – These should be set on
installation.
7
Setting the PROGRAMME
Six time and temperature settings are available in each 24 hour period.
Pressing BACK at any time in this process will return you to normal
operating mode.
If only two different temperature settings are required in 24 hours then set
the first time and temperature using programme one (P1) and the second
time and temperature setting using programme setting two (P2). The
remaining programmes (P3 to P6) should all be set to the same time and
temperature as P2.
This same method can be used if three, four or five temperature levels are
required, always using the first settings to provide the temperature change
commands with the remaining settings that are not required set to the same
time and temperature as the last required setting.
Press ENTER three
times
The day of the week
will flash
Press '-' or '+'
to select day to
programme
Press ENTER
Press ENTER
Time / Temperature
setting P1 will flash
Press '-' or '+' to
select time /
temperature period
you wish to set (P1
to P6)
Temperature will
flash, use the '-' or
'+' to select the
required
temperature
Press ENTER
The hours START
time will flash
Press '-' or '+' to
adjust the hours
then press ENTER.
The minutes will
then flash.
Press '-' or '+' to
adjust the minutes
then press ENTER.
If you require to set further periods for
the same day, the next period will now
automatically flash. Follow this process
again to programme as required
On completion of period 6
(P6) go to the copy
process on Page 9 of this
booklet
8
To copy the same programmes to other days of the week,
please follow the process below
Setting the STANDBY
To exit STANDBY mode, press ENTER TWICE
When you have set
P6 the message 'To
Copy press ENTER'
will appear.
Press '-' or '+' to select the
days you wish to copy the
set programmes. Pressing
ENTER after each day to
confirm
The next
sequential day
will now flash.
When complete press BACK
to return to normal operating
mode
Press ENTER
To programme remaining
days please go to the start of
the process 'Setting the
PROGRAMME'
Press ENTER Twice
The words STANDBY and
Standby Enabled will appear
on the display
Press ENTER
After a short period Standby
Enabled will disappear from
the display
Press '-' or '+' until
STANDBY
appears on the
display
9
Setting the HOLIDAY programme
Pressing BACK at any time in this process will return you to
normal operating mode
Press ENTER twice
The START date
will now flash
Press ENTER
Press the '-' or '+' to
adjust to the date you
wish the holiday
programme to start.
Pressing ENTER to
change between Day,
Month and Year
Press '-' or '+' until
HOLIDAY appears
on the display
The BACK date
will now flash
Again, Press the '-' or '+' to
adjust to the date you wish
the holiday programme to
end. Pressing ENTER to
change between Day,
Month and Year
HOLIDAY
programme is now
set
10
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Secure Thermostat Handbücher
Secure
Secure C1727 Bedienungsanleitung
Secure
Secure STP328 Bedienungsanleitung
Secure
Secure SRT321 Betriebsanleitung
Secure
Secure H3747 Bedienungsanleitung
Secure
Secure ThermoPlus AS1 Betriebsanleitung
Secure
Secure SEC_SRT321 Gebrauchsanweisung
Secure
Secure SCS311 Bedienungsanleitung
Secure
Secure SRT323 Betriebsanleitung
Secure
Secure SRT322 Betriebsanleitung
Secure
Secure C1727 Bedienungsanleitung
Beliebte Thermostat Handbücher anderer Marken
EWELLY
EWELLY EW-181 Bedienungsanleitung
Prolon
Prolon T1100 Montageanleitung
Computherm
Computherm Q20 Bedienungsanleitung
Heatmiser
Heatmiser neoStat Bedienungsanleitung
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung
