SeeMeCNC Orion delta Bedienungsanleitung

SeeMeCNC Guides

Orion Delta RTP User Guide

Written By: JJ Johnson

Orion Delta RTP User Guide

INTRODUCTION

Congrats on your new Factory Assembled Orion Delta! This guide will help you in getting started with

your new machine.

Your machine was fully assembled, calibrated and printed successfully before it left our factory.

Please make sure there are no damages to your new Orion Delta. Inspect it carefully for any broken

parts. If you find any damages please STOP and contact the company that you purchased it from

immediately. Please include your order number when contacting them as it helps to speed up the

process.

Your machine was fully assembled, calibrated and printed successfully before it left our factory. We

have done some things to make sure the machine does not get damaged while shipping the printer.

Please complete the following steps:

Orion Delta RTP User Guide

Step 1 — READ ME FIRST!

Please thoroughly read the Introduction - Read Me First

Want to download this guide as a PDF? Click on the PDF link just above the image and save as

PDF.



Step 2 — Remove Shipping Packaging

Remove the tape and staples from the top of the Orion box. be careful after removing the staples

as they can be sharp!



Inside the top of the box, you will find your getting started instruction sheet.

Lift the Orion straight up out of the box. You can do so by grasping the aluminum extrusions (noted

in the 3rd image with blue arrows) Just let the packaging fall away as you lift the printer out of the

box



Orion Delta RTP User Guide

Step 3 — Remove Packaging

Remove the plastic bag that the printer is protected by.

Remove the shrink wrap on the top of the printer. These wrap is retaining the bag of accessories

that come with the printer.



Gently list up on each of the three carriages a little at a time until they are all above the spool of

filament attached to the build plate.



Orion Delta RTP User Guide

Step 4 — Remove Filament

Remove the 6 bed clips holding the filament and glass plate in place.

Remove the filament and glass plate from the print area.

Carefully cut away the shrink wrap holding it all together. Be very careful not to drop the glass

plate.



Try to hold the glass plate by the edges not touching the surface of the glass plate. Oils on the

glass plate will make it more difficult for prints to stick.



The final item in this bundle is a print removal tool. This assists in getting prints up and off the bed

when they are completed.



Orion Delta RTP User Guide

Step 5 — Install the Glass Plate

Re-install the glass plate on the print bed.

Try to hold the glass plate by the edges not touching the surface of the glass plate. Oils on the

glass plate will make it more difficult for prints to stick.



Secure the glass plate using the supplied binder clips that you originally removed. Position them as

shown.



Slowly and carefully move each of the 3 carriages down to the top of the base assembly.

Step 6 — Inverting the Arms

Slowly and carefully raise the carriages, one at a time until they are all three in printing position. Be

sure to look at all three images before beginning.



Orion Delta RTP User Guide

Step 7 — Accessories

Remove the accessories from the white pouch (originally shrink wrapped to the top of the printer).

Install the power cable where shown.

Install the spool holder arms as shown.

Install the USB cable on the opposite side of the machine as the power cable. (not shown)

Step 8 — Accessories

Remove the protective covering from the front of the LCD screen.

Insert the SD card into the side of the LCD assembly. Note the orientation of the SD card, the

metal contact should be facing you.



Orion Delta RTP User Guide

Step 9 — Loading Filament

Remove the filament from the packaging.

Set the filament spool on the spool holder arms with the filament coming off of the top of the spool.

Route the filament through the two guides in the back of the printer.

Bring the filament to the bottom of the extruder. The extruder is the part on the side of the printer

with the blue "star"



Observe the filament path on the bottom of the extruder. While pressing the red release lever with

your first finger and thumb, insert the filament into that path and feed it upwards until you see it

appear in the bowden tube (clear tube).



Continue feeding the filament up through the bowden tube (clear tube) until you see it reach the hot

end. You can feed filament by either turning the blue stepper motor knob, or by pressing the red

lever and manually feeding the it.



Orion Delta RTP User Guide

This document was last generated on 2017-06-22 12:13:47 AM.

Step 10 — Power On!

The power switch is located above the LCD screen (note the position in the image). Power the

printer on.



You should see an initial splash screen that shows the printer model and firmware version and

compilation date.



Your next step is to download and check out the MatterControl User Manual It will guide you

through setting up MatterControl and running your first print!



You can also check out: Setup and User Guides to find other helpful resources such using the

advanced calibration, changing filament, exporting GCODE to the SD card, and more. It would be a

good idea to bookmark that page.



Orion Delta RTP User Guide

Andere Handbücher für orion delta

Inhaltsverzeichnis

Andere SeeMeCNC 3D-Drucker Handbücher

SeeMeCNC

SeeMeCNC Rostock MAX v2 Bedienungsanleitung

SeeMeCNC

SeeMeCNC Rostock MAX v2 Bedienungsanleitung

SeeMeCNC

SeeMeCNC orion delta Bedienungsanleitung

SeeMeCNC

SeeMeCNC Rostock Max v3 Bedienungsanleitung

SeeMeCNC

SeeMeCNC Delta Bedienungsanleitung

SeeMeCNC

SeeMeCNC ERIS DELTA Bedienungsanleitung

SeeMeCNC

SeeMeCNC Rostock Max Bedienungsanleitung

SeeMeCNC

SeeMeCNC Rostock MAX v2 Bedienungsanleitung

SeeMeCNC

SeeMeCNC Rostock Max v3 Bedienungsanleitung

SeeMeCNC

SeeMeCNC Artemis Bedienungsanleitung

SeeMeCNC

SeeMeCNC orion delta Bedienungsanleitung

SeeMeCNC

SeeMeCNC Rostock MAX v2 Bedienungsanleitung

SeeMeCNC

SeeMeCNC Artemis 300 Bedienungsanleitung

SeeMeCNC

SeeMeCNC rostock max v2.0 Bedienungsanleitung

SeeMeCNC

SeeMeCNC DropLit Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch