SeeMeCNC Rostock MAX v2 Bedienungsanleitung

SeeMeCNC Guides

Rostock MAX v2 RTP User Guide

This How-To will get you started with your new Factory Assembled Rostock Max v2 3D Printer

from SeeMeCNC. It will cover: Unpackaging and Setup, Software Install, Setup, and How to

Operate your new 3D Printer, and Getting Connected.

Written By: JJ Johnson

Rostock MAX v2 RTP User Guide

Step 1 — Unpackaging and Setup

Your machine was fully assembled, calibrated and printed successfully before it left our factory.

We have done some things to make sure the machine does not get damaged while shipping the

printer. Please complete the following steps



Carefully remove all shrink wrap from the printer. Be careful not to cut the machine if you are using

a knife.



The arms have been inverted to prevent the hot end nozzle from striking the glass print surface

during shipping. To invert the arms from shipping position to printing position, place your hand on

ONE of the carriages and slowly move this carriage upward toward the top of the printer.



Next select one of the two remaining carriages and repeat.

Do the same operation with the final carriage.

Remove the BLUE calibration print from the print bed. (we leave that on there for you to see that

your printer has been calibrated and printed on and is ready for printing)



Rostock MAX v2 RTP User Guide

Step 2 — Unpackaging and Setup Continued

The spool holder has been removed from the machine and you will need to reinstall it. Locate the

spool holder and insert the 3 nylon lock nuts as shown in the second image.



Finally, position the spool holder on the top of the machine as shown in the third image. Use the (3)

6-32 x 1” machine screws to secure the spool holder to the top plate.



Step 3 — Unpackaging and Setup Continued

Install the spool holder arms as

shown in the image.



Rostock MAX v2 RTP User Guide

Step 4 — Unpackaging and Setup Continued

Install the AC power cord

Install the USB cable (Note: the front left piece of acrylic has been removed in the image to make

the location of the USB port more easily recognized. You can easily gain access to this location by

removing the front LCD Controller Module. This module is fastened to the machine with (2) nylon

thumb screws.)



Rostock MAX v2 RTP User Guide

Step 5 — Software Install, Setup, and How to Operate your new 3D Printer

Download: Rostock Max v2 User Manual

Familiarize yourself with the READ ME FIRST section on page 2

Perform the driver installation as instructed on pages 5-6

YOU DO NOT NEED TO PERFORM THE STEPS ON PAGES 7-12. THE PRINTER'S FIRMWARE

IS ALREADY LOADED ONTO THE RAMBO BOARD.



Familiarize yourself with the LCD and Front Panel Controls on pages 13-15

Install and configure MatterControl as directed on pages 17-22

YOU DO NOT NEED TO PERFORM THE INITIAL FUNCTION TESTS ON PAGES 23-35. YOUR

PRINTER IS ALREADY FULLY CONFIGURED AND CALIBRATED



Get some practice printing! Pages 36-42 in the manual will teach you how to print a fan shroud on

your new printer. This part is already installed on your printer, however this will be good practice

for learning how to operate the software and printer.



Rostock MAX v2 RTP User Guide

Step 6 — Software Operation

Read through the remainder of the

manual about:



MatterControl Basics: Slicing

(pages 53-62)



MatterControl Basics: Loading

and Printing Objects (pages 63 -

68)



Advanced MatterControl:

Configuration (pages 69 - 82)



Advanced MatterControl: Settings

- Filament (pages 83 - 86)



Advanced MatterControl: Settings

- Printer (pages 87 - 89)



Using the 3D and Layer Views

(pages 90 - 98)



A Strategy for Successful (and

Great!) Prints (pages 99 - 112)



Rostock MAX v2 RTP User Guide

This document was last generated on 2017-06-18 10:31:06 PM.

Step 7 — Getting Connected

Join our community of 3D Printing enthusiasts by visiting www.forum.seemecnc.com

Should you need any customer support, please visit SeeMeCNC and submit a support ticket.

Chat with live technicians Monday - Friday 8am - 4pm EST.

Rostock MAX v2 RTP User Guide

Andere Handbücher für Rostock MAX v2

Inhaltsverzeichnis

Andere SeeMeCNC 3D-Drucker Handbücher

SeeMeCNC

SeeMeCNC orion delta Bedienungsanleitung

SeeMeCNC

SeeMeCNC Artemis Bedienungsanleitung

SeeMeCNC

SeeMeCNC rostock max v2.0 Bedienungsanleitung

SeeMeCNC

SeeMeCNC Rostock MAX v2 Bedienungsanleitung

SeeMeCNC

SeeMeCNC DropLit Bedienungsanleitung

SeeMeCNC

SeeMeCNC Artemis 300 Bedienungsanleitung

SeeMeCNC

SeeMeCNC ERIS DELTA Bedienungsanleitung

SeeMeCNC

SeeMeCNC orion delta Bedienungsanleitung

SeeMeCNC

SeeMeCNC Rostock Max Bedienungsanleitung

SeeMeCNC

SeeMeCNC Rostock MAX v2 Bedienungsanleitung

SeeMeCNC

SeeMeCNC Rostock Max v3 Bedienungsanleitung

SeeMeCNC

SeeMeCNC orion delta Bedienungsanleitung

SeeMeCNC

SeeMeCNC Delta Bedienungsanleitung

SeeMeCNC

SeeMeCNC Rostock MAX v2 Bedienungsanleitung

SeeMeCNC

SeeMeCNC Rostock Max v3 Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch