Sega World Series Baseball Super Major League Bedienungsanleitung

1ST PRINTING MAY 01

MANUAL NO. 999-1288

Owner’s Manual

SEGA ENTERPRISES, INC. USA

Upright Version

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies

that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workman-

ship or materials under normal operating conditions. This also certifies that all Interactive Control

Assemblies are to be free from defects in workmanship and materials under normal operating condi-

tions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to

replace or repair the defective part during the warranty period. For Warranty claims, contact your

Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Ne-

glect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other dam-

ages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other

warranties expressed or implied. Under no circumstance shall it extend beyond the period of time

listed above.

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:

To maintain the safety:

To ensure the safe usage of the product, be sure to read the following before using the product. The following

instructions are intended for the users, operators and the personnel in charge of the operation of the product.

After carefully reading and sufficiently understanding the warning displays and cautions, handle the product

appropriately. Be sure to keep this manual nearby the product or elsewhere convenient for referring to it

when necessary.

Herein, explanations which require special attention are enclosed with dual lines. Depending on the poten-

tially hazardous degrees, the terms of WARNING, CAUTION, etc. are used. Be sure to understand the

contents of the displays before reading the text.

Indicates that mishandling the

product by disregarding this

warning will cause a potentially

hazardous situation which can

result in death or serious injury.

Indicates that mishandling the product

by disregarding this caution will cause

a slight hazardous situation which can

result in personal injury and or material

damage.

For the sage usage of the product, the following pictographs are used:

Indicates “HANDLE WITH CARE.” In order to protect the human body an equipment, this

display is attached to places where the Owner’s Manual and or Service Manual should be referred

to.

Perform work in accordance with the instructions herein stated.

Instructions for work are explained by paying attention to the aspect of accident prevention. Failing to

perform work as per the instructions can cause accidents. In the case where only those who have techni-

cal expertise should perform the work to avoid hazardous situation, the instructions herein state that the

serviceman should perform such work.

Be sure to turn off power before working on the machine.

To prevent electric shock, be sure to turn off power before starting the work in which the worker touches

the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual

herein always states to that effect.

Be sure to ground the Earth Terminal (this, however, is not required in the case where a power cord

with earth is used).

This product is equipped with the Earth Terminal. When installing the product, Connect the Earth Termi-

nal to the “accurately grounded indoor earth terminal” by using an earth wire. Unless the product is

grounded appropriately, the user can be subject to electric shock. After performing repair, etc. for the

Control equipment, ensure that the Earth Wire is firmly connected to the Control equipment.

Ensure that the Power Supply used is equipped with an Earth Leakage Breaker.

This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not

equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs.

Be sure to use fuses which meet the specified rating. (only for the machines which use fuses).

Using fuses exceeding the specified rating can cause a fire and electric shock.

Specification changes (removal of equipment, conversion and addition) not designated by SEGA

are not allowed.

The parts of the product include warning labels for safety, covers for personal protection, etc. It is very

hazardous to operate the product by removing parts and or modifying the circuits. Should doors, lids

and protective parts be damaged or lost, refrain from operating the product, and contact where the

product was purchased from or the office herein stated. SEGA shall not be held responsible for any

accidents, compensation for damage to a third party, resulting from the specifications not designated by

SEGA.

Ensure that the product meets the requirements of appropriate Electrical Specifications.

Before installing the product, check for Electrical Specifications. SEGA products have a nameplate on

which Electrical Specifications are described. Ensure that the product is compatible with the power

supply voltage and frequency requirements of the location. Using any Electrical Specifications different

from the designated Specifications can cause a fire and electric shock.

Install and operate the product in places where appropriate lighting is available, allowing warning

labels to be clearly read.

To ensure safety for the customers, labels and printed instructions describing potentially hazardous

situation are applied to places where accidents can be caused. Ensure that where the product is operated

has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again imme-

diately. Please place an order with where the product was purchased from or the office herein stated.

When handling the Monitor, be very careful. (Applies only to the product w/monitor.)

Some of the monitor (TV) parts are subject to high tension voltage. Even after running off power, some

portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be

performed only be those technical personnel who have knowledge of electricity and technical expertise.

Be sure to adjust the monitor (projector) properly. (Applies only to the product w/monitor.)

Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the

monitor not properly adjusted may cause dizziness or a headache to an operator, a player, or the custom-

ers.

When transporting or reselling this product, be sure to attach this manual to the product.

In the case where commercially available monitors and printers are used in this product, only the

contents relating to this product are explained herein. Some commercially available equipment has

functions and reactions not stated in this manual. Read this manual together with the specific Instruc-

tion Manual of such equipment.

Descriptions herein contained may be subject to improvement changes without notice.

The contents described herein are fully prepared with due care. However, should any question arise or

errors be found, please contact SEGA.

•

INSPECTIONS IMMEDIATELYAFTER TRANSPORTING THE PRODUCT TO THE LOCATION.

Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after

transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before

turning on power, check the following points to ensure that the product has been transported in a satisfac-

tory status.

Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet?

Are Casters and Adjusters, damaged?

Do the power supply voltage and frequency requirements meet with those of the location?

Are all wiring connectors correctly and securely connected? Unless connected in the correct direction,

connector connections can not be made accurately. Do not insert connectors forcibly.

Do power cords have cuts and dents?

Do the fuses used meet specified rating? Is the Circuit Protector in an energized status?

Are all accessories available?

Can all Doors and Lids be opened with the Accessory keys? Can Doors and Lids be firmly closed?

When using the cabinet that shares the coin chute between 1P and

2P (such as the NAOMI CABINET, B AST CITY, etc.), change

the setting of the COIN CHUTE TYPE item in the COIN

ASSIGNMENTS screen, from INDIVIDUA to COMMON.

Using these cabinets with the setting of INDIVIDUA disables to

play from the 2P side.

For more information about the COIN ASSIGNMENTS screen,

see the NAOMI Service Manual.

When having connected the power for the first time, open the

SYSTEM MENU - GAME TEST MODE - INPUT TEST screen

and test the input devices; thereby make sure that they can

function normally.

This game is available only with the NAOMI GD-ROM system. It

is not available with other hardware.

TABLE OF CONTENTS

Use of this product is unlikely to cause physical injuries or damages to

property. However, where special attention is required this is indicated by a

thick line, the word "IMPORTANT" and its sign in this manual.

Indicates that mishandling the product by disregarding this

display can cause the product's intrinsic performance not to be

obtained, resulting in malfunctioning.

STOP

IMPORTANT

STOP

IMPORTANT

BEFORE USING THE PRODUCT, BE SURE TO READ THE FO OWING:

1. HAND ING PRECAUTIONS ............................................................................ 2

2. SPECIFICATIONS .............................................................................................. 3 - 4

3. CONTENTS OF GAME ...................................................................................... 5 - 10

4. TEST MODE ........................................................................................................ 11 - 19

A.SYSTEM MENU

B.GAME TEST MODE

a.INPUT TEST

Switch input test is performed.

b.GAME ASSIGNMENTS

Various settings such as game difficulty, etc. can be set.

c.VO UME SETTING

This page allows you to adjust the volume settings used for

the ANA OG STICKS and BAT MECHA.

d.BOOKKEEPING

Allows for checking data such as operation time,

game time, etc.

e.BACKUP DATA C EAR

Clears the contents of BOOKKEEPING.

5. GAME BOARD ................................................................................................... 20 - 21

6. SOFT KIT............................................................................................................. 22 - 23

7. COIN SE ECTOR ............................................................................................... 24 - 27

8. DESIGN RE ATED PARTS ............................................................................... 28

9. PARTS IST (CONTRO PANE ) .................................................................... 29 - 35

10. WIRE CO OR CODE TAB E.......................................................................... 36

11. WIRING DIAGRAM (CONTRO PANE ) ..................................................... 37

To prevent electric shock or IC Board malfunctioning, be sure to turn

off the power for the cabinet when installing or removing the IC Board.

Extraneous matter such as dust on the IC Board can cause the IC Board

to generate heat and result in a fire due to short circuit, etc. Ensure the

IC Board surfaces are always kept clean.

Use NAOMI for the cabinets compatible with JVS. Using NAOMI for

the cabinet other than those compatible with JVS can cause generation

of heat and a fire.

Be sure to connect the IC Board and connectors completely.

Insufficient insertion can damage IC Board, etc.

For the IC Board circuit inspection, only the use of ogic Tester is

permitted.

The use of ordinary testers is not permitted as these can damage the IC

Board.

Do not subject the IC Board to static electricity when installing the IC

Board in the cabinet or when connecting wire harness connectors to the

IC Board.

When soldering buttons, etc. to the wire harnesses, be sure to remove

the wire harnesses from the IC Board so as not to subject the IC Board

to heat.

Using NAOMI without the Shield Case can cause electric wave trouble.

Be sure to use NAOMI together with the accessory Shield Case.

The monitor frequency corresponding to NAOMI is 15kHz or 31kHz.

NAOMI can not be used for the cabinet incorporating a monitor or

projector not corresponding to 15kHz or 31kHz.

1. HANDLING PRECAUTIONS

STOP

IMPORTANT

Concerning the display of JAMMA VIDEO STANDARD:

JAMMA VIDEO STANDARD adopted by NAOMI is referred to as JVS. As

against this Standard, the conventional JAMMA STANDARD which employs

56P Edge Connectors adopted by ST-V, etc. is displayed as Old JAMMA

STANDARD.

The specific Manual attached to each game sometimes displays JVS as JV

STANDARD, New JAMMA STANDARD, or JAMMA 2 STANDARD against

O D JAMMA STANDARD as JAMMA STANDARD, JS, etc.

The contents herein described are subject to change without notice.

2. SPECIFICATIONS

MONITOR

Horizontal Synchronous Frequency

15/31 kHz

CONTRO PANE

NEW ASTRO CITY, NAOMI CABINET, NET CITY, B AST CITY

(PART NO. HOT-20011 or NOA-20010-01)

ANA OG EVER: Move cursor (for throwing, batting); Specify base (for

defense, base running)

A BUTTON: Throw (for defense); Steal base (for batting); Advance to

next base (for base running)

Enter command (within command acceptance time)

B BUTTON: Check runner (for throwing); Move between bases (for

defense); Return to base (for running)

Enter command (within command acceptance time)

BAT MECHA: Swing

START: Start game; Time out (for throwing, batting)

The analog input on the I/O board uses the following channels:

CH0 : 1P ANA OG EVER VO UME VERTICA UP(FFH) DOWN(00H)

CH1 : 1P ANA OG EVER VO UME HORIZONTA EFT(FFH)

RIGHT(00H)

CH2 : 1P BAT MECHA VO UME STANDARD POS.(00H) MAX(FFH)

CH3 : (RESERVE)

CH4 : 2P ANA OG EVER VO UME VERTICA UP(FFH) DOWN(00H)

CH5 : 2P ANA OG EVER VO UME HORIZONTA EFT(FFH)

RIGHT(00H)

CH6 : 2P BAT MECHA VO UME STANDARD POS.(00H) MAX(FFH)

CH7 : (RESERVE)

HORIZONTAL

Monitor Position

FFH

START

1P 2P

00H ABUTTON

BBUTTON

FFH 00H

FFH

00H

FFH

00HABUTTON

BBUTTON

FFH 00H

FFH

00H

ANALOG

LEVER BAT MECHAANALOG

LEVER BAT MECHA

PLAYER 1 PLAYER 2

Minimum DIMM Memory Capacity

256 MB

Removing and Attaching the BAT MECHA

If you need to remove the BAT MECHA as in the case of a failure, open the

control panel base and remove the BAT MECHA through the following

procedure.

To reinstall the BAT MECHA, reverse the removing procedure, being certain that

the BAT MECHA is faced in the correct direction.

For instructions on opening the control panel base, refer to the Instruction Manual

of the cabinet.

To prevent electric shock, be sure to turn off the power for the cabinet when

removing or attaching the BAT MECHA.

The above figure does not show the wiring of the volume and its connector (AMP

3P, white).

Remove the wiring connector (AMP 3P, white) located near the volume.

Remove the tamperproof screw clamping the bat center axis on the front side of

the control panel.

Tightening/loosening of the tamperproof screw should use the tamperproof screw

M4 wrench (540-0006-01) that is included as an accessory for the NAOMI

CABINET, NET CITY, and NEW ASTRO CITY cabinet.

The tamperproof screw M4 wrench is not included with the following cabinets:

Versus CITY, New VERSUS CITY, and B AST CITY.

If the wrench is not available, please order the following part numbers:

• Wrench type (M4): 540-0006-01

• Screwdriver type (M4): 540-0018

Remove the four flange nuts clamping the BAT MECHA body on the back side of

the control panel.

BAT MECHA Part number: 610-0409

Part name: ASSY BAT MECHA

123

3. CONTENTS OF GAME

• This is a sports action game where the Major eague Baseball in the United States

of America was taken as a subject matter.

• In this game, the following teams appear: 14 American and 16 National teams,

and two all-star teams from the two leagues.

• The number of players appearing in the game is over 700. All of the 30 really

existing ballparks also appear there.

• The game player or players operate their favorite teams to participate in the

baseball game, aiming at the win.

• The following play modes are available: Player vs. CPU, Player vs. Player, and

Game of Intrusion.

• First select your favorite from the 32 teams.

Use the lever to designate the selected team, and use the A Button for

determination. This applies also to all the subsequent operations.

• Next select the desired one from the 30 ballparks.

• Then select the starting pitcher. You can select the desired pitcher from the five

candidates appearing on the screen.

• Finally select one of three levels: Easy, Standard, and Hard. The fielding strategy

you use depends on the level you selected.

EGEND - HARD -: Hard.

Both catching and throwing the ball are operated by the

player. The speed of the pitched ball, i.e., pace, is the

maximum.

VETERAN - MEDIUM -: Standard.

Both catching and throwing the ball are operated by the

player. The pace is the standard.

ROOKIE - EASY -: Easy.

All the operations to catching the ball are made by the

CPU. All the subsequent operations are made by the

player.

The pace is the minimum.

• The game start.

The shortest way to the win is to take advantage of the strong points of the

individual baseball players to play the game.

• Apart from the score of the actual baseball game, game points may increase or

decrease, depending on the contents of the baseball game.

If the resulting number of game points is listed at an upper rank when the game is

cleared, your name is included in the entry.

• In the Player vs. CPU or Player vs. Player mode, the game is cleared if the play

continues until the entire baseball game ends, and if you have won, you see the

ending.

• If the difference in score reaches the preset value during the progress of the game,

the game is immediately treated as a called game, resulting in Game Over.

HOW TO P AY THE GAME

Pitching & Batting Screen

Batter's (Batting) Team

By operating the lever,

select the direction of the

Pitch Type Marker arrow

to select the expected

pitch type.

Pull the batting switch

toward you and keep it

there until the pitcher

pitches the ball.

Pitcher's (Fielding) Team

By operating the lever,

select the pitch type by the

direction of the Pitch Type

Marker arrow.

Press the A Button to

initiate the pitch.

The pitching gauge

appears next to the pitcher

on the screen.

1P 123000080 RECORD 200378000 2P 8921000

ABC

XYZ

The baseball player and ball

positions on the ground.

Information in Game

Game Points

(Differs from the actual score

of the baseball game.)

First Base Window

Third Base Window Pitch Type Marker

• The settings in GAME ASSIGNMENTS in the Test Mode control how the game

ends:

EXTRA INNING: If this is ON, the extra part of the baseball game continues to

a maximum of 12th innings.

If this is OFF, the baseball game ends when the bottom of the

ninth inning ends (even if the score is even, i.e., the game is

drawn).

CA ED GAME: Can be set in the 5 to 10 range.

When the difference in score reaches the setting, the baseball

game ends (even if the bottom of that inning is not yet

completed).

• If the game play begins at the other seat while a player is in progress at either 1P

or 2P seat, you enter the Game of Intrusion Mode.

For any play in the Game of Intrusion Mode, the starting inning varies with the

GAME ASSIGNMENTS settings.

INNINGS: For 1 inning, the game begins at the top of the ninth inning.

For 2 innings, the game begins at the top of the eighth inning.

For 3 innings, the game begins at the top of the seventh inning.

For all innings, the game begins at the top of the first inning.

In the Game of Intrusion Mode, the game may continue to up to the bottom of the

ninth inning. The winner can subsequently continue the play in the Player vs.

CPU Mode.

If a draw results from a baseball game in the Game of Intrusion Mode, Game

Over results for both of the players.

GAME SCREEN

Inhaltsverzeichnis

Andere Sega Arcade-Spielautomat Handbücher

Sega

Sega Snakes & Ladders Bedienungsanleitung

Sega

Sega Club Kart Prize Bedienungsanleitung

Sega

Sega Grid 42 Bedienungsanleitung

Sega

Sega MISSION: IMPOSSIBLE Bedienungsanleitung

Sega

Sega House Of The Dead Scarlet Dawn Bedienungsanleitung

Sega

Sega House Of The Dead 3 DELUXE Bedienungsanleitung

Sega

Sega House of the Dead Bedienungsanleitung

Sega

Sega AFTER BURNER CLIMAX Bedienungsanleitung

Sega

Sega OUTRUN 2 SPECIAL TOURS SDX Bedienungsanleitung

Sega

Sega Cows Might Fly Bedienungsanleitung

Sega

Sega Lindbergh Universal Bedienungsanleitung

Sega

Sega Virtua Cop 3 Deluxe Type Bedienungsanleitung

Sega

Sega Luigi's Mansion Arcade Anwendungshandbuch

Sega

Sega Rally 2 DX Bedienungsanleitung

Sega

Sega F355 Challenge Montage- und Bedienungsanleitung

Sega

Sega The House Of The Dead 4 29"STD Bedienungsanleitung

Sega

Sega ALL AIR TRIX DLX Referenzhandbuch

Sega

Sega Ford Racing Full Blown Deluxe Bedienungsanleitung

Sega

Sega The House of the Dead 4 Bedienungsanleitung

Sega

Sega Sonic Allstarts Kids Basketball Bedienungsanleitung

Sega

Sega Sonic Sports Air Hockey 2P Bedienungsanleitung

Sega

Sega House Of The Dead Scarlet Dawn Bedienungsanleitung

Sega

Sega Olle King Bedienungsanleitung

Sega

Sega NAOMI Bedienungsanleitung

Beliebte Arcade-Spielautomat Handbücher anderer Marken

Universal Space

Universal Space COCONUT BASH Bedienungsanleitung

Bay-Tek

Bay-Tek EVOLVE Bedienungsanleitung

Global VR

Global VR America's Army Montage- und Bedienungsanleitung

Atronic

Atronic Cashline Bedienungsanleitung

Universal Space

Universal Space Checky Monkey Bedienungsanleitung

Bay-Tek

Bay-Tek Skee Ball 1908 Alley Bedienungsanleitung

Aristocrat Technologies

Aristocrat Technologies Mars X Upright Bedienungsanleitung

Family Fun Companies

Family Fun Companies Reactor Kurzanleitung

Universal Space

Universal Space FRUIT MANIA Extreme Bedienungsanleitung

falgas

falgas CARRUSEL FIESTA Bedienungsanleitung

Konami

Konami DanceDanceRevolution Bedienungsanleitung

Bay-Tek

Bay-Tek quik drop Bedienungsanleitung

Bandai Namco

Bandai Namco PAC-MAN BATTLE ROYALE CHOMPIONSHIP DELUXE Bedienungsanleitung

Adrenaline

Adrenaline Flying Tickets Montage- und Bedienungsanleitung

Swinks

Swinks Stern Pinball Ghostbusters Bedienungsanleitung

Innovative Concepts in Entertainment

Innovative Concepts in Entertainment MONOPOLY ROLL-N-GO Bedienungsanleitung

jakar

jakar SPEED CARS Bedienungsanleitung

Carmelli

Carmelli HAT TRICK NG1015H Bedienungsanleitung