SEH myUTN-54 Bedienungsanleitung
Quick Installation Guide 1
Monday - Thursday
Friday
8:00 a.m. to 4:45 p.m. and
8:00 a.m. to 3:15 p.m. (CET)
℡+49 (0)521 94226-44
USB Device Server
myUTN-54
Quick Installation Guide
Overview [en]
This Quick Installation Guide provides
a description of the installation of the
myUTN-54. It contains the following
information:
General Information
Safety Regulations
Hardware Installation
Software Installation
Getting Started
Configuring the UTN Server
UTN Server in the WLAN
Please note the table of contents on
page 3. Should you have any further
questions, please contact our support
hotline.
Überblick [de]
Dieser Quick Installation Guide beinhaltet
eine Beschreibung der Installation des
myUTN-54. Sie erhalten die folgenden
Informationen:
Allgemeine Information
Sicherheitsvorschriften
Hardware-Installation
Software-Installation
Erste Schritte
UTN-Server konfigurieren
UTN-Server im WLAN
Beachten Sie das Inhaltsverzeichnis auf
Seite 19. Falls Sie noch Fragen haben,
kontaktieren Sie unsere Support-
Hotline.
2 Quick Installation Guide
Date of Manufacture
The serial number includes the date of manufacture.
The serial number can be found on the type plate.
Quick Installation Guide [en] 3
2 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Scope of Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2 Safety Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2 Getting Started: SEH UTN Manager . . . . . . . . . . . . . . . . 9
Starting the SEH UTN Manager . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Assigning an IP Address to the UTN Server . . . . . . . . . . . . . . 11
Adding the UTN Server to the Selection List . . . . . . . . . . . . . 12
Connecting the USB Device to the Client . . . . . . . . . . . . . . . . 13
2 Configuring the UTN Server . . . . . . . . . . . . . . . . . . . . . . 14
2 UTN Server in the Wireless Network . . . . . . . . . . . . . . 15
Operating the UTN Server in the Wireless Network. . . . . . . 16
Connecting the UTN Server to the Wired Network . . . . . . . 16
Table of Contents
4 [en] Quick Installation Guide
General Information
Purpose
The myUTN-54 allows you to access non-network-ready USB devices (e.g. hard
disks, etc.) in the network. For this purpose, the USB devices will be connected to
the USB ports of the myUTN-54. The software tool SEH UTN Manager handles the
access of the USB devices.
The SEH UTN Manager is installed on all clients that are intended to access a USB
device in the network. The SEH UTN Manager shows the availability of all USB
devices in the network and establishes a connection between the client and the
USB device.
Scope of Supply
Please check the package content before getting started:
UTN server USB Device Server (myUTN-54)
Quick
Installation
Guide
The Quick Installation Guide provides a brief
description of the installation of the myUTN-54.
(This document)
Power pack External power pack
Quick Installation Guide [en] 5
Technical Data
Properties Values
Device connection - 4 x USB 2.0 HS
Network connection logical:
physical:
- IEEE 802.3
- IEEE 802.11g
- IEEE 802.11b
- RJ-45 (STP Cat. 5)
- WLAN module
Operating environment - Ambient temperature: 5 - 40 °C
- Relative humidity: 20 - 80 %
Dimensions - Length: 117 mm
- Width: 70 mm
- Height: 151 mm
- Weight: 220 g (+ 209 g power pack)
Current input - 350 mA @ 12 VDC (without load)
- 1650 mA @ 12 VDC (full load on the USB ports)
1) Reset button
2) Network connector (RJ-45)
for 100BaseTX and 10BaseT
3) USB Port 4
4) USB Port 3
5) USB Port 2
6) USB Port 1
7) Connector for the included
power pack.
8) Link LED (green)
9) Activity LED (yellow):
The LED indicates the
reception of data packets
from the network.
10) Status LED (green):
The LED indicates that the
device is operational.
6 [en] Quick Installation Guide
Safety Regulations
UTN servers are network devices for use in office environments. They are
designed for the integration of USB devices into networks.
Before starting the initial setup procedure and during the operation of the UTN
server, please note the following safety regulations. Their purpose is to protect
yourself and others from personal injuries, and avoid damage to the equipment.
Read the documentation and make sure that your system meets the
requirements listed therein.
Avoid contact with humidity or liquids.
The device must only be connected and operated if it is in perfect condition.
Make sure that no-one steps on or stumbles over the cables.
Do not connect a telephone cable to the RJ-45 connector. The RJ-45
connector may only be connected to SELV voltages. For the connection to the
RJ-45 connector only STP cabling (category 5 or better) may be used. The
shielding must fit flushly to the connector.
Warning! This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
The device must only be operated using the power pack included in the
package.
Do not remove or replace the WLAN module.
Observe the national restrictions which apply for the use of WLAN devices. For
more information, please consult your retailer.
Only use a certified USB Hi-Speed cable for the connection to the UTN server.
You will find a list of certified cables at www.usb.org.
Quick Installation Guide [en] 7
Hardware Installation
You can directly connect four USB devices to the UTN server (myUTN-54).
Clients with the software tool ’SEH UTN Manager‘
Proceed as follows:
1. Connect the UTN server and the USB device to the USB data
cable. (Repeat this step if you want to connect more than one
USB device.)
2. Connect the network cable (RJ-45) to the UTN server.
Note: Even if you want to use the UTN server in a WLAN you
must follow this step in order to carry out the initial
configuration of the UTN server.
3. Connect the power cord to the UTN server.
8 [en] Quick Installation Guide
Software Installation
The software tool ’SEH UTN Manager’ organizes the access of the USB devices.
The SEH UTN Manager is installed on all clients that are intended to access a USB
device in the network.
The SEH UTN Manager is available in two versions:
Single-User Version (SEH UTN Manager)
Multi-User Version (SEH UTN Manager + SEH UTN Service)
A major difference between the single-user version and the multi-user version is
the Windows service ’SEH UTN Service’. A detailed description can be found in the
myUTN User Manual.
Make sure that:
- The installation of the SEH UTN Manager is suitable for Windows XP and
later.
- The installation can only be carried out by Windows users with
administrative rights.
First, you have to download the installation file for the SEH UTN Manager from
the homepage of SEH Computertechnik GmbH:
http://www.seh-technology.com/products/usb-device-servers/products/
myutn-54-downloads.html
Scan this QR code using your smart phone to get direct access to the homepage.
Proceed as follows:
1. Start the installation file.
2. Follow the installation routine.
The SEH UTN Manager is installed on your client.
Quick Installation Guide [en] 9
Getting Started: SEH UTN Manager
After the SEH UTN Manager is started, the network will be scanned for connected
UTN servers. The network range to be scanned is freely definable.
After the network scan all UTN servers found – together with the connected
devices – will be shown in the 'network list'. The preferred devices will be selected
and added to the 'selection list'. The devices in the selection list can be connected
to the client.
This chapter describes the first steps with the program.
’Starting the SEH UTN Manager’ 10
’Assigning an IP Address to the UTN Server’ 11
’Adding the UTN Server to the Selection List’ 12
’Connecting the USB Device to the Client’ 13
Client and UTN server communicate via the UTN port 9200. This port must not be
blocked by a firewall. If necessary, you can change the port number and/or use a
secure UTN SSL port.
A detailed description can be found in the myUTN User
Manual.
Detailed information on how to use the SEH UTN Manager can be found
in the Online Help. To start the Online Help, select Help – Online Help
from the menu bar.
10 [en] Quick Installation Guide
Starting the SEH UTN Manager
Start the SEH UTN Manager on your client via the Windows start menu.
(Start --> Programs --> SEH Computertechnik GmbH --> SEH UTN Manager)
During the initial configuration, client and UTN server must be assigned to the
same local network segment.
Inhaltsverzeichnis
Sprachen:
Andere SEH Server Handbücher
SEH
SEH myUTN-250 Bedienungsanleitung
SEH
SEH myUTN-50a Bedienungsanleitung
SEH
SEH myUTN-50 Bedienungsanleitung
SEH
SEH myUTN-52 Bedienungsanleitung
SEH
SEH dongleserver Pro Bedienungsanleitung
SEH
SEH myUTN-120 Bedienungsanleitung
SEH
SEH myUTN-50 Bedienungsanleitung
SEH
SEH myUTN-80 Bedienungsanleitung
SEH
SEH Mac OS 8 Bedienungsanleitung
SEH
SEH myUTN Bedienungsanleitung
SEH
SEH ProMAX Bedienungsanleitung
SEH
SEH myUTN-50a Bedienungsanleitung
SEH
SEH mySND-120 Bedienungsanleitung
SEH
SEH INU-100 Handbuch
SEH
SEH Dongleserver myUTN-800 Bedienungsanleitung
SEH
SEH myUTN-50 Bedienungsanleitung
SEH
SEH myUTN-80 Bedienungsanleitung
SEH
SEH myUTN-50a Bedienungsanleitung
SEH
SEH myUTN utnserver Pro Bedienungsanleitung
SEH
SEH utnserver Pro Bedienungsanleitung
Beliebte Server Handbücher anderer Marken
iRobo
iRobo IPC2U Bedienungsanleitung
Nortel
Nortel 1000 Con?guration guide Bedienungsanleitung
Asus
Asus AP7500 Bedienungs- und Wartungshandbuch
Avid Technology
Avid Technology AirSpeed 5000 Bedienungsanleitung
HP
HP Integrity rx2600 Installationsanleitung
Milestone
Milestone Husky IVO 350T Bedienungsanleitung