Seiko V195A Kurzanleitung

PARTS LIST /TECHNICAL GUIDE

ANALOGUE SOLAR Cal. V195A

[SPECIFICATIONS]

1/24

Item Cal. No. V195A

Power reserve

Driving system

Additional function

Crown operation

Loss/Gain

Regulation system

Number of jewels

Normal position

1st click position

Current consumption

Gate time for rate measurement

Power

supply

Motion of the second hand

Coil resistance

Power generator

Rechargeable battery

Operating voltage range

2nd click position

One-second intervals

Stepping motor 4 pieces

Diameter: Outside 27.6 mm

Casing 27.0 mm

Height: 4.4 mm

3 hands (hour, minute, small second hands)

Calendar display

Stopwatch (second, hour, minute)

Small alarm display (hour, minute)

Energy depletion forewarning function (The second hand moves at two-

second intervals.)

Overcharge prevention function

Power reserve indicator

Electronic circuit reset function

Second hand stop function

Daily alarm

Instant setting device for calendar

System reset function

World time function

Stopwatch function..........60-minute stopwatch in 1/5-second increments

(Auto stop measuring at 60 minutes)

Accumulated elapsed time measurement

Split time measurement

Single-time alarm function

Stopwatch hand position adjustment

Stopwatch, Power reserve display

Time setting, Setting “0” of stopwatch hand, System reset

Monthly rate:less than 15 seconds (worn on the wrist at temperature range

between 5 to 35 degrees Centigrade)

Use 10-second gate

Nil

Solar power generation system

Movement: less than 0.95 μA Circuit block: less than 0.30 μA

4002 567 1.40 - 1.80 kΩ

(COIL BLOCK) (COIL BLOCK FOR CHRONOGRAPH 1/5 - SECOND)

4002 568 1.30 - 1.70 kΩ

(COIL BLOCK FOR INDICATOR) (COIL BLOCK FOR ALARM)

MT920 Manganese titanium-lithium rechargeable battery

0.90V - 2.10V

From full charge to stoppage: Approximately 6 months

Nil

Time setting of alarm, Calendar setting

SPECIFICATIONS

2/24

Cal. V195A

FEATURES

The Cal. V195A is a solar alarm chronograph epuipped with a calendar function.

l Solar power generation system

The watch operates while charging electricity by converting light received on the dial to

electrical energy. It lasts for 6 months after full charge.

l Energy depletion forewarning function

When the energy stored in the rechargeable battery is reduced to an extremely low level, the

second hand starts moving at 2-second intervals instead of the normal 1-second intervals.

l Guideline of charging time

Environment/Light source Illumination

(lux)

Time required

for full charge

Time required

for steady

operation

Time to charge

1 day of power

General ofﬁces/ Fluorescent

Light

700 -60 hours 150 minutes

30W 20cm/Fluorescent light 3,000 110 hours 13 hours 33 minutes

30W 3cm/ Fluorescent light 10,000 30 hours 3.5 hours 9 minutes

Cloudy weather/Sunlight 10,000 30 hours 3.5 hours 9 minutes

Fair weather/Sunlight 100,000 5 hours 0.6 hours 2 minutes

The above table provides only a general guideline.

It is recommended that the watch be charged for as long as the charging time according to the

column "Time required for steady operation" in this table in order to assure the stable movement

of the watch.

l Caution for charging

When charging the watch, do not place it too close to a photo ﬂash light, spotlight, incandescent

light or other light sources as the watch temperature will become extremely high, causing damage

to the parts inside the watch.

When exposing the watch to sunlight to charge it, do not leave it on the dashboard of a car, etc.

for a long time, as the watch temperature becomes extremely high.

While charging the watch, make sure the watch temperature does not exceed 60 °C.

Order of disassembly: 1

Order of assembly:　　　1

Lubricating:

Types of oil Oil quantity

AO-3 Normal quantity

AO-2

Piezoelectric Element 4589 801

Case Back

Case Back Gasket

Hour, Minute

and Small

Second Hands,

Chronograph

Hands (Hour,

Minute and 1/5

Second), Mode

Indicator Hand

Dial

Spacer for Solar Cell

4453 500

Solar Cell

4025 569

Holding Ring for Dial

0866 ***

Contact Point Spring

2pcs.

4281 516

Crown

Case

Movement

Anti Magnetic

Shield Plate B

4259 519

PARTS LIST Cal. V195A

3/24

Guide Plate Fixing Pin for

Calendar Correction

0027 973

Guide Plate for Calendar

Correction

4288 500

3rd Intermediate Wheel for

Calendar Correction

0962 504

2nd Intermediate Wheel for

Calendar Correction

0962 504

1st Intermeidate Wheel for

Calendar Correction

0962 580

Date Dial Guard

Screw (2pcs.)

0012 354

Date Dial Guard

0808 523

Date Dial

0878 ***

Date Dial Guide Plate Screw

0012 354

Guide Plate for Date Dial

0712 507

Date Corrector Setting Wheel

0737 505

Date Driving Wheel

0802 580

24-Hour Wheel for Alarm

0278 503

Hour Wheel

0271 636

Cal. V195A

PARTS LIST

4/24

Battery Clamp Screw（3 pcs.）

0022 230

Friction Spring for Second

Counting

0396 580

Buzzer Lead

Terminal

4246 527

Rechargeable Battery Clamp

4225 677

Rechargeable Battery Block

3023 24D

Circuit Block Cover Screw（3 pcs.）

0022 459

Circuit Block Cover

4461 599

Conducting Plate

4224 525

Circuit Block

4000 970

PARTS LIST Cal. V195A

5/24

Indicator Wheel

0902 502

Minute Wheel for Alarm

0264 580

Intermediate Wheel for

Indicator

0950 590

First Intermediate

Wheel for 1/5- Second

0885 590

Pin for Train Wheel

Bridge

0027 974

Train Wheel Bridge

0125 527

1/5-Second Counting Wheel

0888 501

Fourth Wheel and Pinion

0241 583

Third Wheel and Pinion

0231 580

Second Intermediate Wheel

for 1/5-Second

0885 591

Minute Wheel

0261 580

Center Wheel for Alarm

0902 502

Small Second Wheel

0240 521

Intermediate Wheel for

Alarm

0950 590

Fifth Wheel and Pinion

0701 581

Cal. V195A

PARTS LIST

6/24

Chronograph 1/5-Second

Rotor

4146 710

Coil Block for

Indicator

4002 568

Coil Block

4002 567

Coil Block for Chronograph

1/5-Second

4002 567

Step Rotor

4146 710

Indicator Rotor

4146 710

Setting Wheel

0281 580

Clutch Wheel

0282 585

Spacer for Center

Wheel and Pinion

4283 581

Rotor Stator

4239 710

Rotor Stator for

Chronograph

1/5-Second

4239 711

Rotor Stator for Indicator

4239 713

Coil Block for Alarm

4002 568

Alarm Rotor

4146 710

Switch Lever A

4450 703

Setting Lever

0383 592

Yoke

0384 583

Setting Stem

0351 586

Train Wheel Setting Lever

0391 591

Center Wheel and Pinion

0221 604

Rotor Stator for Alarm

4239 713

Switch Lever B

4450 701

Main Plate

0100 579

PARTS LIST Cal. V195A

7/24

GUIDE PLATE FIXING PIN FOR CALENDAR CORRECTION 0027 973

PIN FOR TRAIN WHEEL BRIDGE 0027 974

15 0027 973 30 0027 974

Cal. V195A

PARTS LIST

8/24

l

How to ﬁnd the correct parts, if not determined by 4 digit caliber number

Following parts are determined based on the design of watches, such as hands height, dial color,

and design of cases. Please refer to the SEIKO WATCH PARTS CATALOGUE in order to choose

the corresponding parts.

5HOLDING RING FOR DIAL 0866 ***

9DATE DIAL 0878 ***

SETTING STEM 0351 586

The type of HOLDING RING FOR DIAL is determined based on the design of cases.

Check the case number and refer to the "SEIKO WATCH PARTS CATALOGUE" to choose the

corresponding parts.

l

How to ﬁnd the correct pins

Please choose the corresponding pins.

Refer to the following ﬁgures.

4 SOLAR CELL 4025 556

Cal. Parts Number

V198A 4025 556

V195A 4025 569

28 CIRCUIT BLOCK 4000 970

Make sure to hole position on a CIRCUIT BLOCK for V195A in order to distinguish from others.

Cal. V195A

Cal. V198A

No hole

Hole

Note: Sollar cell differs according

to each caliber.

No hole

PARTS LIST Cal. V195A

9/24

lTools and consumables required for disassembling/reassembling

•Movement holder

UNIVERSAL MOVEMENT HOLDER (S-682)

• Watch oils

SEIKO watch oils (AO-3 and AO-2) and SEIKO watch grease S-6

AO-3 AO-2

S-6

TECHNICAL GUIDE Cal. V195A

10/24

REMARKS ON DISASSEMBLING AND REASSEMBLING

Set the notched portions of the dial to the guide posts (4 posts)

of the HOLDING RING FOR DIAL, and check that the dial is ﬁxed

in position.

• How to install

1HANDS

• How to install

2DIAL

* Match the polarity of the ROTORs for stopwatch and alarm,

and then install the hands.

Check that the voltage of rechargeable battery exceeds 1.2 V

and the watch is working.

*Crown position: normal position.

Short-circuit in touching the AC pattern and the Rechargeable

Battery Clamp with tweezers (refer to the Fig. 1).

In order to match the polarity of the ROTORs, pull out the crown

to the second position, then short-circuit in touching the Pattern

A and the Rechargeable Battery Clamp with tweezers (refer to

the Fig. 2).

Install the Mode indicator hand at “E” position and the Alarm

(hour / minute) hands at “12” position.

Install the Small second hand, the Hour hand, the Minute hand

and the Chronograph second hand at “0” position.

Fig. 1

Fig. 2

3SPACER FOR SOLAR CELL

Set the notched portions of the SPACER FOR SOLAR CELL to

the guide posts (5 posts) of the HOLDING RING FOR DIAL, and

check that the dial is ﬁxed in position.

• How to install

pattern A

Inhaltsverzeichnis

Andere Seiko Betrachten Handbücher

Seiko

Seiko Cal. 8L35 Bedienungsanleitung

Seiko

Seiko 6N76A Kurzanleitung

Seiko

Seiko S252 Bedienungsanleitung

Seiko

Seiko C-20 Bedienungsanleitung

Seiko

Seiko V172A Kurzanleitung

Seiko

Seiko Prospex SJE085J Bedienungsanleitung

Seiko

Seiko Essentials SSB333 Bedienungsanleitung

Seiko

Seiko 4R36 Bedienungsanleitung

Seiko

Seiko Astron 3X22 Bedienungsanleitung

Seiko

Seiko 7T52B Kurzanleitung

Seiko

Seiko DH33A Installationshandbuch

Seiko

Seiko Analog Quartz 7T32 Bedienungsanleitung

Seiko

Seiko 8X53 Series Bedienungsanleitung

Seiko

Seiko Pulsar Y182 Bedienungsanleitung

Seiko

Seiko S06 Bedienungsanleitung

Seiko

Seiko 6M25 Bedienungsanleitung

Seiko

Seiko Alarm Chrono 7T32 Betriebsanleitung

Seiko

Seiko 5Y19A Kurzanleitung

Seiko

Seiko S141A Installationshandbuch

Seiko

Seiko MOMENTUS CC238 Bedienungsanleitung

Seiko

Seiko Astron 8X82 Bedienungsanleitung

Seiko

Seiko 6R51 Bedienungsanleitung

Seiko

Seiko PJN103P1 Bedienungsanleitung

Seiko

Seiko Grand 3F81 Bedienungsanleitung

Beliebte Betrachten Handbücher anderer Marken

Pandora

Pandora WATCH2 Bedienungsanleitung

Casio

Casio QW-4343 Bedienungsanleitung

Suunto

Suunto X6 Bedienungsanleitung

MotionX

MotionX 365 Bedienungsanleitung

Garmin

Garmin VENU SQ 2 Bedienungsanleitung

QCY

QCY Watch GTC Bedienungsanleitung

Canyon

Canyon Cindy CNE-KW41WP Bedienungsanleitung

Esq

Esq Watches Installationsanleitung

Crane

Crane AA5-CDSM-3A Bedienungsanleitung

Timex

Timex W-214 Bedienungsanleitung

DETOMASO

DETOMASO MATERA Bedienungsanleitung

Geemarc

Geemarc Watch N Shake Bedienungsanleitung

LORUS

LORUS W590 Bedienungsanleitung

STENLILLE

STENLILLE Actío Bedienungsanleitung

Casio

Casio 5594 Bedienungsanleitung

Sinn

Sinn HUNTER'S WATCH 3. Edition Bedienungsanleitung

Slazenger

Slazenger SLZ800 Bedienungsanleitung

iTOUCH

iTOUCH 3360 Bedienungsanleitung