Seko Maxima MPG Bedienungsanleitung

Maxima MPG Cod. EM00136006 rev. 1.1 1

MAXIMA

MPG

Contents:

1 First of all 3

2 Installation 9

3 Setting and operation 12

4 Maintenance 32

5 Troubleshooting 33

6 How to contact us 34

Maxima MPG Cod. EM00136006 rev. 1.1 2

1 FIRST OF ALL

1.1 WELCOME

Thank you for buying a Seko product.

This dosage pump is made up of a control part that houses the electronics and the magnet and

a hydraulic part that is always in contact with the liquid to be dosed.

The parts that come into contact with the liquid are chosen to guarantee full compatibility with

most chemical products, normally used. Due to the variety of chemical products on the market,

we recommend checking chemical compatibility between the product dosed and the materials in

contact with it. The materials that make up the pump are listed in Paragraph 1.3.1, while all

membranes are made of PTFE.

Pay particular attention to the warnings and precautions indicated in this manual.

1.2 COMPOSITION OF THE SYSTEM

1 Control Panel

2 Head

3 Knob for adjusting the stroke

4 Delivery connector

5 Suction connector

6 Priming valve

7 Support for sides and base.

Maxima MPG Cod. EM00136006 rev. 1.1 3

1.3 PACK CONTENTS

MAXIMA MPG

Complete pump

Foot filter (Fig. 1)

Injection fitting(Fig. 2)

4 m of PVC hose (transparent and soft) for suction and for connecting

the bleeding valve up for manual priming (Fig. 3)

2 m of PE pipe (opaque and rigid) for connecting the pump’s outlet to

the injection point (Fig. 3)

Anchors for securing the pump.

Support for wall mounting (Fig. 4)

Instruction Manual

Fig. 1: Foot filter

Fig. 2: Injection fitting

Fig. 3: Hoses (suction, delivery,

bleeding)

Fig. 4: Support

Fig. 5: Fitting the support to the tank

Fig. 6: Fitting the pump onto the support

Maxima MPG Cod. EM00136006 rev. 1.1 4

WARNINGS

CAREFUL HANDLING, INSTALLATION AND COMMISSIONING OF THE PUMP HELPS TO

PROVIDE A TROUBLE-FREE INSTALLATION.

 READ THE FOLLOWING WARNINGS BEFORE PROCEEDING TO INSTALL OR DO

MAINTENANCE WORK ON THE PUMP.

− All our pumps are tested using water. To dose chemical products that may react with the water (e.g.

H2SO4= Sulphuric Acid) all the internal parts of the hydraulic section must be dried. To do

so:

a Switch the power to the pump on and run it at maximum frequency with the delivery valve facing

downwards.

b After it has run for a few minutes check that no more water is coming out.

− Install the pump in a place where the temperature does not exceed 40°C and the relative humidity is

below 90%. This pump has a protection level of IP65 and so can be installed outdoors. This pump

must never be immersed in liquid. To prevent overheating do not install the pump in direct sunlight.

− Install the pump in such a way that inspection and maintenance are easy, and then secure the pump

well to prevent vibrations.

− Check that the power supply voltage fed to the plant is as indicated in the label on the pump.

 WARNING: BEFORE DOING ANY WORK ON THE PUMP, ALWAYS FIRST DISCONNECT

THE POWER SUPPLY CABLE.

− When handling the pump after it has been used to dose chemical products, remember to use

protective clothing and gloves and to provide suitable protection for your eyes.

− If you are dosing using pressurised piping, before starting the pump always check that the pressure in

the plant does not exceed the maximum working pressure shown on the dosage pump label.

Maxima MPG Cod. EM00136006 rev. 1.1 5

1.4 TECHNICAL CHARACTERISTICS

 Check the main characteristics of you pump on the plate.

MAXIMA 240 Spm

Type bar lit/h Gph Psi

10 8.5 2.25 145

6 9.8 2.59 87

2 11 2.91 29

MPG912

230VAC

50/60 Hz

40 W

Fuse 2 A L

Code MPG912ASC0M00 Serial N°

XXXXXX

Your pump is one of the family of pumps listed in the table below:

Pressure

Flow Rate

Connections

(mm)

Weight

Model

bar lit/h

cc/stroke

IN / OUT

Strokes/min

10 1.80 0.13

6 2.00 0.14

611 3 2.20 0.15

4 / 6 240 1,7

7 5 0.35

4 5.5 0.38

612 1 8.4 0.58

4 / 6 240 1,7

18 4.5 0.31

16 5 0.35

911 11 5.6 0.39

4 / 6 240 3,1

10 8.5 0.59

6 9.8 0.68

912 2 11 0.76

4 / 6 240 3,1

5 15 1.39

4 18 1.67

913 3 20 1.85

8 / 12 180 3,2

2 35 2.43

1 44 3.06

914 0 63 4.38

8 / 12 240 3,2

Maxima MPG Cod. EM00136006 rev. 1.1 6

1.5 WARNINGS

 Check the model of the equipment bought, when using the dosage calibration

references indicated in this manual.

 ATTENTION – Stroke adjustment

The knob must not be rotated when the pump is not working; otherwise the adjustment

shaft could become deformed thus causing a flow rate loss.

 WARNING: Always follow the necessary safety procedures, including the use of

adequate protection for the eyes, face, hands, and clothing.

 WARNING: When installing or carrying out maintenance on this equipment, always

disconnect it from the power supply.

Seko is constantly striving to perfect all its products, and we therefore reserve the right to

make changes at any time without notice.

Failure to abide by the standards laid down in this manual could result in damage to

property or people, as well as damaging the equipment or compromising its operation.

Maxima MPG Cod. EM00136006 rev. 1.1 7

2 INSTALLATION

 WARNING: Before proceeding to install the pump, read all the paragraphs referring to it carefully.

This pump must be installed in a position that makes connecting it to the chemical product tank and

the injection point easy.

This pump has a protection level of IP65 and so can be used outdoors. This pump must never be

installed in positions in which it may be submerged. It must also not be installed where the

temperature exceeds 40°C for long periods of time.

2.1 RECOMMENDED INSTALLATION LAYOUTS

Fig. 7: Wall-mounted with bracket

Fig. 8: On the tank with a support

Fig. 9: Under a head with a

support

Fig. 10: On a meter

Maxima MPG Cod. EM00136006 rev. 1.1 8

2.2 OVERALL DIMENSIONS AND DRILLING TEMPLATE

Fig. 11: Overall dimensions – 610 series

Fig. 12: Overall dimensions – 910 series

Fig. 14: Drilling template for 610 series

Fig. 13: Drilling template for support

Fig. 15: Drilling template for 910 series

Maxima MPG Cod. EM00136006 rev. 1.1 9

2.3 PLUMBING CONNECTIONS

1) Injection point

2) Injection fitting

3) PVDF gasket

4) Washer holder

5) Pipe clamp

6) Ring nut

7) Delivery pipe (opaque and rigid)

8) Delivery fitting

9) Pump casing

10) Manual bleeding valve

11) Suction coupling

12) Suction hose (soft and transparent)

13) Foot filter

When forming the plumbing connections, follow these instructions:

− The FOOT FILTER must be installed in such a way that it is always 5-10 cm from the bottom to prevent any

deposits clogging it and damaging the hydraulic part of the pump.

− Installing the pump under a head is always best and is recommended for pumps with a very low flow rate as it

solves all priming problems. Installation under a head is specifically recommended when dosing

sodium hypochlorite (NaOCl) and hydrazine (N2H2) or any other product that tends to develop gas.

− Pumps are supplied standard with entry and exit pipes that are sized to suit the pump’s hydraulic

characteristics. Should you need to use longer pipes, it is important to use pipes with the same internal and

outside diameter as those supplied with the pump.

− For outdoor applications, where the DELIVERY PIPE may be exposed to direct sunlight, we recommend

using black piping that is resistant to ultraviolet rays.

− It is advisable to position the INJECTION POINT towards the top of the pump or the tank. In all cases, to

guarantee the pump’s performance, always use the INJECTION VALVE supplied with the pump.

− THE INJECTION VALVE MUST ALWAYS BE INSTALLED AT THE END OF THE DELIVERY LINE FOR

THE DOSAGE FLOW.

Maxima MPG Cod. EM00136006 rev. 1.1 10

2.4 ELECTRICAL CONNECTIONS

The pump must be connected to a power supply that is as indicate don the label on the side of

the pump. Failure to respect the limits indicated may result in the pump being damaged.

The MAXIMA range of pumps do not need to be earthed as they are made using components

and technology that ensures that all electronic components are double insulated.

The pumps are designed to absorb small extra voltages, but to avoid the pump being damaged

it is always preferable to avoid using a power supply in common with electrical equipment that

generates other voltages.

The connection with the 380V three-phase line is formed exclusively between phase and

neutral. No phase-earth connections are to be formed. (Fig. 16 and Fig 17)

380V

230V

Fig. 16: CORRECT CONNECTION

380V

230V

Fig. 17: WRONG CONNECTION

Inhaltsverzeichnis

Andere Seko Wasserpumpe Handbücher

Seko

Seko KOMPACT DPT Bedienungsanleitung

Seko

Seko KRONOS 50 Bedienungsanleitung

Seko

Seko OPL BASIC Bedienungsanleitung

Seko

Seko AKTUA ATR-05S Handbuch

Seko

Seko Tekna Evo TPG series Bedienungsanleitung

Seko

Seko KOMPACT AMC Bedienungsanleitung

Seko

Seko OPL Mini L Handbuch

Seko

Seko TEKNA EVO TPG Bedienungsanleitung

Seko

Seko KOMPACT AMC 200 Bedienungsanleitung

Seko

Seko SAM 5-ME Benutzerhandbuch

Seko

Seko TDS Series Bedienungsanleitung

Seko

Seko PoolMatch pH Bedienungsanleitung

Seko

Seko MSA Series Bedienungsanleitung

Seko

Seko PULV Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung