Select Engineered Systems Select Gate 1A Bedienungsanleitung

User/Installer

Guide

Select Entry Systems

This page intentionally blank.

.TABLE OF CONTENTS

1.0 INTRODUCTION TO SELECT GATE .............................................. 1

1.1 STANDARD FEATURES .................................................................. 2

1.2 SPECIAL FEATURES ...................................................................... 3

1.3 OPTIONS ....................................................................................... 3

1.4 ENVIRONMENTAL CONSIDERATIONS ......................................... 3

1.5 ELECTRICAL ................................................................................. 3

1.6 TECHNICAL DATA ......................................................................... 4

2.0 INSTALLATION INSTRUCTIONS .................................................... 5

3.0 WIRING HOOKUP CONNECTIONS ................................................ 6

3.1 INSTALLATION PROCEDURE ........................................................ 7

3.1.1 MOUNTING SELECT GATE ............................................................ 7

3.1.2 GROUNDING SELECT GATE .......................................................... 8

3.1.3 CONNECTING POWER TO SELECT GATE ................................... 9

3.1.4 TELEPHONE CABLES TO USE TO WIRE SELECT GATE............ 10

3.1.4.1 CONNECTING RJ-31X .......................................................... 11

3.1.4.2 CONNECTING TO HOMES WITH ALARM SYSTEM .......... 12

3.1.5 CONNECTING DEVICES TO CONTROL RELAY ........................... 13

3.1.6 REX INPUT ....................................................................................... 14

3.1.7 ADJUSTING SPEAKER VOLUME ................................................... 15

3.1.8 ADJUSTING MICROPHONE SENSITIVITY .................................... 16

3.1.9 CHANGING SELECT GATE LIGHT BULB ...................................... 17

4.0 INITIALIZATION AND PROGRAMMING ......................................... 18

4.1 CONFIGURING SELECT GATE ...................................................... 18

4.2 FACTORY DEFAULTS AND PROGRAMMING FUNCTIONS ......... 19

4.2.1 PIN CODES .................................................................................... 20

4.2.2 PHONE CODES ............................................................................. 20

4.2.3 RELAY 1 UNLOCK TONE ............................................................... 21

4.2.4 RELAY 1 LATCH TONE.................................................................... 21

4.2.5 RELAY 1 ONE HOUR TONE ...... .................................................... 21

4.2.6 RELAY 1 OPEN TIME ..................................................................... 21

4.2.7 STRIKE OUT COUNT ..................................................................... 22

4.2.8 LOCK OUT TIME ........................................................................... 22

4.2.9 RELAY 2 UNLOCK TONE ............................................................... 22

4.2.10 RELAY 2 LATCH TONE ................................................................. 23

4.2.11 RELAY 2 ONE HOUR TONE ........................................................... 23

4.2.12 RELAY 2 OPEN TIME .................................................................... 23

TABLE OF CONTENTS

4.2.13 RING TYPE ........................................................................... 24

4.2.14 RING COUNT ........................................................................ 24

4.2.15 CALL WAITING TYPE .......................................................... 25

4.2.16 RING DETECT ....................................................................... 25

4.2.17 BACK BEEP ........................................................................... 25

4.2.18 TALK TIME ............................................................................ 26

4.2.19 KEYPAD ON .......................................................................... 26

4.2.20 PROGRAMMING PASSWORD ............................................. 26

4.2.21 CALL FORWARD TONE ........................................................ 26

4.4.22 CALL FORWARD TYPE ......................................................... 26

4.2.23 CALL FORWARD ON/OFF ..................................................... 27

4.2.24 CALL FORWARD NUMBER ................................................. 27

4.2.25 CLEAR ALL PHONES ........................................................... 27

4.2.26 CLEAR ALL PINS .................................................................. 27

4.2.27 PRESET ALL RELAYS .......................................................... 27

4.2.28 CLEAR ALL CALL FORWARD PARAMETERS ................... 28

4.2.29 PRESET ALL MEMORY ........................................................ 28

4.3 EXITING PROGRAMMING MODE ..................................................... 28

5.0 SELECT GATE OPERATION ........................................................... 29

5.1 SELECT GATE CALLING HOUSE .................................................. 29

5.2 SELECT GATE CALLING HOUSE WHEN PHONE IN USE .......... 30

5.3 SELECT GATE CALLING OUTSIDE PHONE ................................. 30

5.4 SELECT GATE USING PIN CODES ............................................... 31

5.5 CALLING SELECT GATE FROM HOUSE ...................................... 31

5.6 PROGRAMMING SELECT GATE FROM HOUSE .......................... 32

5.6.1 PROGRAMMING SELECT GATE FROM OUTSIDE PHONE ........ 32

5.6.2 EXITING PROGRAMMING MODE ................................................... 32

APPENDIX A SETUP INFORMATION ....................................................... 33 - 35

APPENDIX B QUICK PROGRAMMING GUIDE ....................................... 36

APPENDIX C SELECT GATE CONFIGURATION GUIDE........................... 37

SELECT GATE SG-1A V1.X

SELECT ENGINEERED SYSTEMS 11/01 1

1.0 INTRODUCTION TO SELECT GATE

The SelectGateisaproductthatactsasanintercomandaccesscontrolsystem. TheSelect

Gate, when started, intercepts a telephone company phone line and initiates a calling/ringing

sequence to the telephone set equipment (up to 5 phones of standard ringer equivalence) in the

house or residence. It then provides a voice communication channel from the Select Gate to the

telephone set.

If the telephone company line is in use at the time of activation, or if the Select Gate is

communicating toatelephonesetwhenanexternallygeneratedringsignalisdetected,anindicating

tone will be placed on the telephone set line at the house or residence. The access management

functions are controlled via DTMF (Touch-Tone™) signaling.

The Select Gate is activated by

pressing the call button or the "#" on the

keypad. Select Gate tones will be

provided to alert the caller of system

operation.

For dialing outside numbers

(other than the house or residence) the

Select Gate is a microprocessor based

device that will allow entering 1 digit. It

then automatically dials the phone

number that was programmed into

memory. The Select Gate provides a

relay output for controlling doors, gates,

or any device actuated by a contact

closure or contact opening. The Select Gate has programmable 1 to 9 minute talk-time limit, with

warning tones near the end of talk time.

APersonal Identification Number (PIN) is available. Entering a 4 digit PIN code, while the

Select Gate is on hook, will energize the maincontrol relay. (This assumes a valid PIN number has

been programmed into the Select Gate).

While the Select Gate is dialing, the speaker is disconnected, keeping the dialed phone

number confidential.

Calling the Select Gate from a Touch-Tone™ telephone will allow the user to control the 2

output relays. When the Select Gate is called, the Select Gate will ring, go offhookandsendaone

second tone. Enteringthepropertwodigitcontrolpasswordwillallowaccesstotheoutputrelaysand

allow timed,latch and one hour relay control functions. If the 4 digit program password is entered,

the Select Gate will enter Remote Programming mode.

SELECT GATE SG-1A V1.X INSTALLATION AND USER GUIDE

1.1 STANDARD FEATURES:

• Lighted front panel.

• Uses existing phones and phone lines.

• (Local) Call waiting and transfer.

• Latching relays by calling unit from any Touch-Tone™ phone. (Local or remote).

• 1 hour relay open function.

• Call forwarding function.

• Non-volatile EEPROM memory.

• 100 programmable entry codes (PINS), 4 digits.

• Postal lock input available.

• Request to exit input.

• Unlock time is programmable from 1 to 99 seconds.

• Weather resistant housing.

• Programmable without opening cabinet, from keypad or remote telephone.

• Talk time field programmable from 1 - 9 min.

• Tamper input.

• Crystal controlled tone detection for short burst 50 MS tone.

• Unit will mute tones in speaker during dialing.

• Entry code attempts (strike out) programmable from 0 - 9.

• Remote relay activation.

SELECT GATE SG-1A V1.X

SELECT ENGINEERED SYSTEMS 11/01 3

1.2 SPECIAL FEATURES

• Unit will not accept Touch-Tone™ signals through the microphone.

• (4) ring styles, programmable.

•Programmablebackground "beep"to indicateyou aretalking tothe gate,when SelectGate has

called an outside line.

• Keypad "Beep" feedback.

• Can call unit to activate speaker/microphone, local or remote.

• Ability to call off premises phone numbers, up to 10 (16) digit numbers.

• Remote Touch-Tone™ Programming (locally or off premises), password controlled.

• Multiple relay capability.

1.3 OPTIONS:

CCTV camera.

1.4 ENVIRONMENTAL CONSIDERATIONS

Indoor or Outdoor: ThestandardSelectGatehousingissuitableforoutdoorinstallations. Optional

pedestal mounts for curb (PST236), street (PST242), or slab mounting (PST1) are also available.

Dimensions: Select Gate's largest outside dimensions are 9½" W X 7" H X 4½" D.

1.5 ELECTRICAL

Power: TheSelectGateuses16voltac50/60Hz. A16vac20vatransformerissuppliedwitheach

purchaseinthe U.S.only. Theinstallermaychoosetoprovidetheirown12volt@2ampDCsupply.

Ground: TheSelectGatemustbeconnectedtoagoodearthgroundwithatleast#16ga.stranded

wire. This wire MUST be a minimum of 16 ga. connected to a ground rod or cold water pipe. The

maximum wire length is 50 feet. Surge damage protection built into Select Gate is diminished if

adequate earth ground is not provided.

Relay capabilities: 24 volts AC or DC at2 amp. Form "C" (N/O N/C) contacts are on the control

output relay for controlling devices.

Gate controllers: Some solid-state gate controllers react to the over-voltage protection devices

used on all SES products. This is a gate controller dependent problem. The symptom is an

intermittent gate open condition, or gate stuck open condition, sometimes occurring after using the

latching function. If this occurs, add an external relay controlled by the Select Gate output relay

contacts to your gate system. This will help isolate the contacts going to your solid state gate

controller.

SELECT GATE SG-1A V1.X INSTALLATION AND USER GUIDE

1.6 TECHNICAL DATA

• POWER INPUT: 16 VAC 20 VA UL LISTED TRANSFORMER (PROVIDED WITH UNIT).

• TELEPHONE LINE: RJ31X JACK.

• SHIPPING WEIGHT: APPROXIMATELY 8 LBS.

• CONSTRUCTION: FRONT PANEL: 16 GA. STAINLESS STEEL.

BACKBOX:PAINTED CHEMICALLY TREATED ALLOY ALUMINUM.

• OPERATING ENVIRONMENT:TEMPERATURE: -20EF TO +140EF.

RELATIVE HUMIDITY: 5% - 95% NON-CONDENSING.

• RELAY OUTPUT: 2 RELAYS: FORM C DRY CONTACT 24V @ 2 AMP.

• MOUNTING: SURFACE

• MEMORY TYPE: NON-VOLATILE.

• TONE DETECTION: CRYSTAL CONTROLLED, CAN DETECT SHORT BURST 50 MS TONE.

SELECT GATE SG-1A V1.X

SELECT ENGINEERED SYSTEMS 11/01 5

2.0 INSTALLATION INSTRUCTIONS

NOTE THE FOLLOWING BEFORE ATTEMPTING ANY INSTALLATION:

A. Never install telephone wiring during a lightning storm.

B. Never install telephone jacks in wet locations unless the jack is specifically designed for wet

locations.

C. Never touch uninsulated telephone wires or terminals unless the telephone line has been

disconnected at the network interface.

D. Use caution when installing or modifying telephone lines.

Installation of Select Gate requires co-ordination with your telephone company. It is

recommended that a Touch-Tone™ line be installed to allow much faster dialing.

The phone company may require the following information:

The ringer equivalence number.

The FCC registration number.

These numbers are on the label on the inside door of the Select Gate.

The desired location of the telephone jack must be given to the phone company at the time

the phone line is ordered, if required.

NOTE: TELEPHONE COMPANY REQUIRES ACCESS TO TELEPHONE LINE

ORIGINATION POINT. SES RECOMMENDS THAT RJ31X JACK BE

INSTALLED IN HOUSE OR MADE ACCESSIBLE TO TELEPHONE COMPANY

PERSONNEL.

SELECT GATE SG-1A V1.X INSTALLATION AND USER GUIDE

3.0 WIRING HOOKUP CONNECTIONS

Inhaltsverzeichnis

Andere Select Engineered Systems IP-Zugriffskontrollsysteme Handbücher

Select Engineered Systems

Select Engineered Systems TEC1A Series Montageanleitung

Select Engineered Systems

Select Engineered Systems SG2CL Montageanleitung

Beliebte IP-Zugriffskontrollsysteme Handbücher anderer Marken

ZKTeco

ZKTeco SpeedFace-V5L Bedienungsanleitung

Jantar

Jantar REX A-1-9 Bedienungsanleitung

2N Access Unit Merkblatt

Kedacom

Kedacom KSCA120 Series Bedienungsanleitung

H3C

H3C WX2880X Bedienungsanleitung

G4S

G4S S870-EX Leitfaden

PRASTEL

PRASTEL M2000PE Bedienungsanleitung

Allegion

Allegion interflex IF-281 Cylinder Bedienungsanleitung

TECOM

TECOM TS1067E Bedienungsanleitung

Fermax

Fermax Memokey 100C Benutzerhandbuch

Fermax

Fermax CITYLINE MEMOKEY Bedienungsanleitung

Software House

Software House iSTAR Pro 2U RM Bedienungsanleitung

AKCP

AKCP SP+ Bedienungsanleitung

Bpt

Bpt HNA/102 Bedienungsanleitung

Civintec

Civintec CV9601T-T-1F Bedienungsanleitung

BioMax

BioMax N-X90W Bedienungsanleitung

ZKTeco

ZKTeco OP-200 Bedienungsanleitung

FingerTec

FingerTec s-Kadex Bedienungsanleitung