Seneca Z201 Bedienungsanleitung
MI00065-3-EN INSTALLATION MANUAL 1/4
INSTALLATION MANUAL
SENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY; Tel. +39.049.8705359 - Fax +39.049.8706287
WARNING: The full content of this manual must be read before any operation. The module must only be used by
qualied electricians. Specic documentation is available via QR-CODE shown on page 1.
Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling).
The symbol on the product or its packaging shows the product must be surrendered to a collection centre
authorized to recycle electrical and electronic waste.
The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to
electrostatic discharges. Take appropriate measures during any operation.
PRELIMINARY WARNINGS
The word WARNING preceded by the symbol indicates conditions or actions that put the user's safety at risk.
The word ATTENTION preceded by the symbol indicates conditions or actions that might damage the
instrument or the connected equipment. The warranty shall become null and void in the event of improper use or
tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if
the instructions contained in this manual are not followed.
CONTACT INFORMATION
This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised.
The content of this document corresponds to the described products and technologies.
Stated data may be modied or supplemented for technical and/or sales purposes.
DOCUMENTATION
Z201
Z201
MI00065-3-EN INSTALLATION MANUAL 2/4
MODULE LAYOUT
SIGNALS VIA LED ON FRONT PANEL
LED STATUS LED meaning
PWR On Device powered
Off Device not powered
Dimensions LxHxD: 17.5 x 102.5 x 111 mm; Weight: 110 g; Enclosure: PA6, black
SW1
111 mm
17.5 mm
102.5 mm
TECHNICAL SPECIFICATIONS
CERTIFICATIONS
https://www.seneca.it/products/z201/doc/CE_declaration
POWER SUPPLY Voltage: 19
÷
40 Vdc; 19
÷
28 Vac 50
÷
60 Hz, max.: 2.5W
INPUT Current: 0
÷
5 AaC or 0
÷
10 AaC settable by terminal panel.
Insulation 3700 Vac.
OUTPUT
Current 0
÷
20 or 4
÷
20 mA, maximum load 600 Ohm;
Voltage 0
÷
10 or 0
÷
5 Vdc, 2
÷
10 or 1
÷
5 Vdc.
Minimum load 2500 Ohm.
ENVIRONMENTAL
CONDITIONS
Operating temperature:
from -20°C to +55°C
Humidity: 10% ÷ 90% non condensing.
Storage temperature: from -30°C to +85°C
Protection rating: IP20
RESPONSE TIME < 200 ms
PERMISSIBLE
OVERLOAD 12A continuative, 30A for 1 s.
POWER
SUPPLY/OUTPUT
PROTECTION
against impulse voltage overload 400W/ms.
INSTALLATION
CLASS
III, it can be applied on a three-phase network of up to 500 Vac phase-phase,
300Vac phase-ground.
1 2 3
4 5 6
7 8 9
10 11 12
MI00065-3-EN INSTALLATION MANUAL 3/4
ERRORS REGARD FIELD OF INPUT MEASUREMENT AND WITH INPUT > 10% OF THE SCALE.
Frequency band
Calibration error
Thermal coefcient Linearity error Other
20
÷
400Hz sinus. 0.3% 0.02%/°C 0.1% 1% max for EMC
400
÷
1000Hz sinus. 0.5% 0.02%/°C 0.2% 1% max for EMC
SETTING THE DIP-SWITCHES
On the side of the module there are dip switches that can be used to select the desired functions. To select these
functions, set the DIP switches as shown in the tables:
SW1 DIP-SWITCH SETTINGS
DIP 1 DI2
ON 4..20mA / 1..5V / 2..10V ON 0..10V / 2..20V
OFF 0..20mA / 0..5V / 0..10V OFF 0..5V / 1..5V
INSTALLATION REGULATIONS
The module has been designed for vertical installation on a DIN 46277 rail. For optimal operation and long life,
adequate ventilation must be provided. Avoid positioning ducting or other objects that obstruct the ventilation slots.
Avoid mounting modules over heat-generating equipment. Installation in the bottom part of the electrical panel is
recommended.
MI00065-3-EN INSTALLATION MANUAL 4/4
ELECTRICAL CONNECTIONS
CAUTION
Switch the module off before connecting inputs and outputs.
To meet the electromagnetic immunity requirements:
- use shielded signal cables;
- connect the shield to a preferential instrumentation earth system;
- separate shielded cables from other cables used for power installations (transformers, inverters, motors, etc...).
INPUT
OUTPUT
Voltage Applied current External power supply current
POWER SUPPLY
The upper power supply limits must not be exceeded, as this might
cause serious damage to the module.
The power supply source must be protected from any failures in the
module by means of a suitably sized fuse.
When connected to a T.A.
one of the wires must be
grounded.
7
8
9
7
8
9
Input for In < 10A Input for In < 5A
V
+
3
2
1
6
5
4
+
A
+
3
2
1
6
5
4
6
5
4A
+
3
2
1
Vac / Vdc
Vac / Vdc
Inhaltsverzeichnis
Andere Seneca Medienkonverter Handbücher
Seneca
Seneca S117P1 Bedienungsanleitung
Seneca
Seneca ZC-SG Bedienungsanleitung
Seneca
Seneca Z109REG-BP Bedienungsanleitung
Seneca
Seneca S107USB Bedienungsanleitung
Seneca
Seneca Z Series Bedienungsanleitung
Seneca
Seneca Z-SG3 Bedienungsanleitung
Seneca
Seneca Z111 Bedienungsanleitung
Seneca
Seneca Z-SG2-L Bedienungsanleitung
Seneca
Seneca S117P1 Bedienungsanleitung
Seneca
Seneca Z204-1 Bedienungsanleitung
Seneca
Seneca Z-SG3 Bedienungsanleitung
Seneca
Seneca Z201-H Bedienungsanleitung
Seneca
Seneca Z-4RTD2-SI Bedienungsanleitung
Seneca
Seneca Z-SG Bedienungsanleitung
Seneca
Seneca Z109REG-BP Bedienungsanleitung
Seneca
Seneca Z Series Bedienungsanleitung
Seneca
Seneca Z-SG Bedienungsanleitung
Seneca
Seneca EASY-USB Bedienungsanleitung
Seneca
Seneca Z-MBus Bedienungsanleitung
Seneca
Seneca K109S Bedienungsanleitung
